Recommended locations for your thermostat.
To ensure that your thermostat provides accurate readings and controls effectively, it must be installed approximately 1.5 m above floor level on an inside wall, away from direct sunshine and any other sources of heat or cold such as radiators, cold draughts, etc.
MOUNTING OF WALL MOUTING PLATE
All wiring must be in accordance with IEE regulations. This product is for fixed wiring only.
OPTIMISATION EXPLAINED
Historically, most UK heating systems waste vast amounts of energy by firing unnecessarily early for most of the year. Homeowners tend to set their boiler on times based on when they wake up by guessing what time they feel that their boiler should fire in order to reach the requested target temperature; for example turning the boiler on at 6am in order to have a warm room/ home by their wake up time at 7am.
Dual function optimisation , priority to comfort or energy savings, the choice is yours:
Depending on various parameters: room inertia, ambient temperature, desired temperature, the thermostat calculates and optimizes the programming for each heating period whether set to Comfort or Savings (Eco):
In OPTI COMFORT mode, priority to comfort
In OPTI COMFORT mode, the thermostat’s inbuilt algorithm optimises in order to guarantee maximum comfort during the COMFORT programme.
In OPTI ECO mode, priority to energy savings
In OPTI ECO mode, the thermostat’s inbuilt algorithm optimises in order to guarantee maximum energy savings throughout the ECO programme.
PLEASE READ BEFORE PROGRAMMING THE THERMOSTAT
Instead of using a fixed start time, Optimum Start calculates how long the house will take to warm up depending on the temperature of the home, then fires the boiler automatically at the most efficient moment in order to reach your target temperature by your programmed time.
HOW DOES OPTIMUM START WORK?
Optimum Start works on a daily basis. You set the time that you want to be warm and Optimum Start will do the rest; for example – if you wake up at 7:30AM, then set your thermostat’s start time for 7:30AM. Optimum Start ensures that you are warm when you want to be (and not before), reducing wasted energy and saving money (up to 10% of energy costs). To change the optimisation type, refer to the installation instructions/ advanced installer settings.
Access
Move the mode slider to
Set 12/24 hours clock
Enable/disable automatic summer/winter change over
Set °C/°F temperature
Set calibration
Program lock
Select 2 points/TPI
The pre-set control algorithm is TPI.
Dual function optimization, priority to comfort or energy savings, the choice is yours:
Depending on various parameters: room inertia, ambient temperature, and desired temperature, the thermostat calculates and optimizes the programming for each heating period whether set to Comfort or Savings (Eco):
Optimization choice
Display disappears on thermostat.
The heating does not come on or does not go off.
You want to change the operating mode but when you move the mode slider nothing happens.
The thermostat is in Auto Mode but programs are not being executed by the boiler:
The thermostat does not control properly.
Note: It is recommended to replace annually as part of the normal system service and before leaving the property empty for a prolonged period.
Environment:
UKCA declaration of conformity: We, Neomitis Ltd, hereby declare under our sole responsibility that the products described in these instructions comply with statutory instruments 2016 No.1101 (Electrical Equipment safety Regulations), ), 2016 No.1091 (Electromagnetic Compatibility Regulations) , 2012 n°3032 (ROHS) and following designated standards:
Neomitis Ltd: 16 Great Queen Street, Covent Garden, London, WC2B 5AH UNITED KINGDOM – contactuk@neomitis.com
EU declaration of conformity
We, Imhotep Creation, hereby declare under our sole responsibility that the products described in these instructions comply with the provisions of Directives and harmonized standards listed below: –
Control class and energy contribution, according to ERP 2009/125/EC and related regulations
Class IV – PID Room Thermostat, for use with on/off heating devices. Electronic room thermostat that controls both the cycle time of the thermostat and the ratio between on and off periods during the same cycle of the heating device, depending on the room temperature. PID control reduces the average water temperature, improves the accuracy of room temperature control, and increases system efficiency. The symbol , affixed on the product indicates that you must dispose of it at the end of its useful life at a special recycling point, in accordance with European Directive WEEE 2012/19/EU. If you are replacing it, you can also return it to the retailer from which you buy the replacement equipment. Thus, it is not ordinary household waste. Recycling products enables us to protect the environment and to use less natural resources.
NEOMITIS
DOWNLOAD MANUAL
Neomitis RTE7D WIRED PROGRAMMABLE ROOM THERMOSTAT Instruction Manual
OTHER MANUALS:
Neomitis RTE7D WIRED PROGRAMMABLE ROOM THERMOSTAT operating instructions
Neomitis RTE7D WIRED PROGRAMMABLE ROOM THERMOSTAT Product Specifications Guide
Neomitis RTE7D WIRED PROGRAMMABLE ROOM THERMOSTAT Instruction Manual
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…