Hotowell HTW-WF06-FC Smart Touch Screen Thermostat
General
HTW-WF06-FC series Smart Wifi fan coil thermostat is widely used in this environment like Homes, Residential buildings, Schools, Hotels, Hospitals, Offices and etc. to main an ideal room temperature purpose.
Features
- 17 Mainstreaming Languages synchronize in APP(English, Spanish, Russian, Hungarian, Turkey, Hebrew, German,
- Italian, Japanese, French, Poland, simplified Chinese, traditional Chinese, Holland, Portuguese, Vietnamese, Arabic, Korean)
- Snap-In Easy Installation
- Fit for EU & Standard Junction Electric Box
- Easily Work with Amazon Alexa, Google Assistant, IFTTT
- Group Control in 1 App
- Fashion Sense of Science and Technology
Ordering Guide
Typical Wiring
- A=HTW-WF06-FC-2
- 2 pipe(tube) system
- 3-speed fan
- NO/NC valve
- B= HTW-WF06-FC-4
- 4 pipe(tube) system
- 3-speed fan
- 2 NO/NC valve
- C=HTW-WF06-FC-MN
- 3-Speed fan output
- 1 a load of Modulating 0~10V output
- Modbus Communication
Specification
- Power Supply 95~240Vac, 50/60Hz
- Current Load Fan Relay 5A(3A-inductive)
- Storage Temp. -5 ~ 45 °C
- Power Consumption < 1.5W
- Housing Material PC +ABS ( Fireproof)
- Wires on Terminals Wire 2 x 1.5 mm2 or 1 x 2.5 mm2
- Protection Class IP20
- Sensor NTC3950, 10K
- Temperature Accuracy ±0.5°C or ±1℉
- Set-Point Range 5~35°C
- Display Temp. Range 5 ~ 99°C
- Timing Error < 1%
- Installation Box EU or Standard Electric Box
- Operating Buttons Capacitive Touch Buttons
Installation
- Make sure the power is OFF! Try turning ON your heating/cooling system by changing the temperature.
- If you can’t get the system to turn ON in 5 minutes, you’ll know the power is OFF.
- Take off the installation faceplate by rotating and gently pulling, then connect voltage supply/load output/external sensor(if with) wires respectively to appropriate terminals.
- Fix the installation plate onto the electric junction box with screws packed in the box.
- Fasten the thermostat display part and the installation faceplate through the groove.(Installation process completed)
Dimensions
Display
Operation
Installer Set-UP Process (ISU)
- The installation personnel with non-professional training shall not perform this operation! During the thermostat power off, Press these 2 buttons M & simultaneously, and hold for 5 seconds to enter
- ISU process. Press to adjust the configurable parameter value, and press M to switch to the next parameters.
- The ISU process will automatically exit and be confirmed after 5 seconds with no operation.
Wifi Connection
Step 1- Download and Install APP
- Use your smartphone or tablet PC to scan the QR code below or Search “SMART LIFE” in the app store /Google Play to download and install the APP.
Step 2- Register your account
- Open the “SMART LIFE” application, click “Allow” on the pop-up notification dialog
- Press the “register” button on the register page
- Select your region and type in your phone No. or email then you may get a verification code.
- Type in your password and confirm to complete your registration.
- If you already have an account, please just log in.
Step 3- Connect App with Thermostat
On the thermostat
During power-off status, press and hold the arrow icon for 8 sec until the connecting icon appears on the thermostat screen and flashes once a sec.
On the App
- Press the “+” on the upper right corner of the page or “Add Device” to add “Thermostat”.
- Click “Confirm indicator rapidly blink” then select your network and back to your App to enter the password of your wireless router and confirm.
- The App will connect with the thermostat successfully. The connecting process takes 5~90 sec, the thermostat name can be editable once connected
Alternative AP mode Connection
- If the thermostat has already been connected under above steps, please ignore this process.***
- This SMART LIFE App is only supported on 2.4GHz Wi-Fi channels.
- If the router does not be supported, or the wi-fi signal is weak or thermostat can not be connected as above steps, please try this AP mode connection process.
On the thermostat
- During power off status, press and hold the arrow icon for 8 sec until the connecting iconappears on the thermostat screen and flashes once a sec.
- press and hold the arrow icon for 8 sec again, the icon will flash once per 3 sec
- indicating connecting from normal router mode.
- Indicates connecting from AP mode.
On the App
- Click “Confirm indicator slowly blink” then select your network and back to your app to enter the password of your wireless router and confirm.
- The app will go into the page
- Press “Connect now” to select the wifi signal Smart life-XXXX from the thermostat
- This AP mode connection process may typically take approx. 5~90 seconds to complete.
- The thermostat name can be edited after the connection
Operation Icons on APP
Programmable Schedule Setting
When the thermostat runs in programmable mode, click the “schedule setting” to switch to the schedule page, where you can simply configure the weekly programmable 5+2 schedule up to 6-period each day. (Workdays=Monday~Friday, Weekend=Saturday and Sunday) Click “Complete” to save the configuration.
Group Control and Info. Modify
- Press the menu button, then click “Create Group”. Select all the rooms you want and confirm, edit the group name or ungroup
- Group Control allows to control all thermostats(+∞ units) configuration in the group at the same time
Share Thermostat with Others
- Method 1: Click “Share with Family”
- Method 2: Click “Profile”>” Sent”>” Add”>Switch on the device>” Share with New Member”>Type in the telephone number you would like to share with.
- Method 3:Home page of the device>Menu>” Device Sharing”>” Add”>>Type in the telephone number you would like to share with.
Work with 3rd party Echo Control
Click “Profile”>” Integration”>Select amazon echo/Google Home/IFTTT>” Use Now”
Customize Scene
- This process is to customize your own personal scenes to suit your needs, for example, set your home temperature automatically when you come back home.
- There are 4 scenes in the default setting, and can be added/deleted at will.
- Here set an example of a specific scene: “leave home for holiday” and turn on the thermostat when the temperature is lower than 5°C
- Scenes>+>Enter a name for the scene>Add a condition(Below 5°C)>Add a Task>Save
Trouble Shooting
Warranty
Products are warranted for 2 full years (checking and repairing services) from the date of purchase which products are not being damaged by any man-made factors.
- Service outwith the warranty period may incur an extra charge.
- For more details please contact Hotowell directly.
REFERENCE:
DOWNLOAD MANUALS:
Hotowell HTW-WF06-FC Smart Touch Screen Thermostat User Manual
Hotowell HTW-WF06-FC Smart Touch Screen Thermostat User Manual