Hotowell HTW-WF06-FC Smart Touch Screen Thermostat User Manual

HTW-WF06-FC series Smart Wifi fan coil thermostat is widely used in this environment like Homes, Residential buildings, Schools, Hotels, Hospitals, Offices and etc. to main an ideal room temperature purpose.

Features

17 Mainstreaming Languages synchronize in APP(English, Spanish, Russian, Hungarian, Turkey, Hebrew, German,
Italian, Japanese, French, Poland, simplified Chinese, traditional Chinese, Holland, Portuguese, Vietnamese, Arabic, Korean)
Snap-In Easy Installation
Fit for EU & Standard Junction Electric Box
Easily Work with Amazon Alexa, Google Assistant, IFTTT

Group Control in 1 App
Fashion Sense of Science and Technology

Ordering Guide

Typical Wiring

A=HTW-WF06-FC-2
- 2 pipe(tube) system
- 3-speed fan
- NO/NC valve
B= HTW-WF06-FC-4
- 4 pipe(tube) system
- 3-speed fan
- 2 NO/NC valve
C=HTW-WF06-FC-MN
- 3-Speed fan output
- 1 a load of Modulating 0~10V output
- Modbus Communication

Specification

Power Supply 95~240Vac, 50/60Hz
Current Load Fan Relay 5A(3A-inductive)
Storage Temp. -5 ~ 45 °C
Power Consumption < 1.5W
Housing Material PC +ABS ( Fireproof)
Wires on Terminals Wire 2 x 1.5 mm2 or 1 x 2.5 mm2
Protection Class IP20
Sensor NTC3950, 10K
Temperature Accuracy ±0.5°C or ±1℉
Set-Point Range 5~35°C
Display Temp. Range 5 ~ 99°C
Timing Error < 1%
Installation Box EU or Standard Electric Box
Operating Buttons Capacitive Touch Buttons

Installation

Make sure the power is OFF! Try turning ON your heating/cooling system by changing the temperature.
If you can’t get the system to turn ON in 5 minutes, you’ll know the power is OFF.
Take off the installation faceplate by rotating and gently pulling, then connect voltage supply/load output/external sensor(if with) wires respectively to appropriate terminals.
Fix the installation plate onto the electric junction box with screws packed in the box.
Fasten the thermostat display part and the installation faceplate through the groove.(Installation process completed)

Dimensions

Display

Operation

Installer Set-UP Process (ISU)

The installation personnel with non-professional training shall not perform this operation! During the thermostat power off, Press these 2 buttons M & simultaneously, and hold for 5 seconds to enter
ISU process. Press to adjust the configurable parameter value, and press M to switch to the next parameters.
The ISU process will automatically exit and be confirmed after 5 seconds with no operation.

Wifi Connection

Step 1- Download and Install APP

Use your smartphone or tablet PC to scan the QR code below or Search “SMART LIFE” in the app store /Google Play to download and install the APP.

Step 2- Register your account

Open the “SMART LIFE” application, click “Allow” on the pop-up notification dialog
Press the “register” button on the register page
Select your region and type in your phone No. or email then you may get a verification code.
Type in your password and confirm to complete your registration.
If you already have an account, please just log in.

Step 3- Connect App with Thermostat

On the thermostat
During power-off status, press and hold the arrow icon for 8 sec until the connecting icon appears on the thermostat screen and flashes once a sec.

On the App

Press the “+” on the upper right corner of the page or “Add Device” to add “Thermostat”.
Click “Confirm indicator rapidly blink” then select your network and back to your App to enter the password of your wireless router and confirm.
The App will connect with the thermostat successfully. The connecting process takes 5~90 sec, the thermostat name can be editable once connected

Alternative AP mode Connection

If the thermostat has already been connected under above steps, please ignore this process.***
This SMART LIFE App is only supported on 2.4GHz Wi-Fi channels.
If the router does not be supported, or the wi-fi signal is weak or thermostat can not be connected as above steps, please try this AP mode connection process.

On the thermostat

During power off status, press and hold the arrow icon for 8 sec until the connecting iconappears on the thermostat screen and flashes once a sec.
press and hold the arrow icon for 8 sec again, the icon will flash once per 3 sec
indicating connecting from normal router mode.
Indicates connecting from AP mode.

On the App

Click “Confirm indicator slowly blink” then select your network and back to your app to enter the password of your wireless router and confirm.
The app will go into the page
Press “Connect now” to select the wifi signal Smart life-XXXX from the thermostat
This AP mode connection process may typically take approx. 5~90 seconds to complete.
The thermostat name can be edited after the connection

Operation Icons on APP

Programmable Schedule Setting
When the thermostat runs in programmable mode, click the “schedule setting” to switch to the schedule page, where you can simply configure the weekly programmable 5+2 schedule up to 6-period each day. (Workdays=Monday~Friday, Weekend=Saturday and Sunday) Click “Complete” to save the configuration.

Group Control and Info. Modify

Press the menu button, then click “Create Group”. Select all the rooms you want and confirm, edit the group name or ungroup
Group Control allows to control all thermostats(+∞ units) configuration in the group at the same time

Share Thermostat with Others

Method 1: Click “Share with Family”
Method 2: Click “Profile”>” Sent”>” Add”>Switch on the device>” Share with New Member”>Type in the telephone number you would like to share with.
Method 3:Home page of the device>Menu>” Device Sharing”>” Add”>>Type in the telephone number you would like to share with.

Work with 3rd party Echo Control
Click “Profile”>” Integration”>Select amazon echo/Google Home/IFTTT>” Use Now”

Customize Scene

This process is to customize your own personal scenes to suit your needs, for example, set your home temperature automatically when you come back home.
There are 4 scenes in the default setting, and can be added/deleted at will.
Here set an example of a specific scene: “leave home for holiday” and turn on the thermostat when the temperature is lower than 5°C
Scenes>+>Enter a name for the scene>Add a condition(Below 5°C)>Add a Task>Save

Trouble Shooting

Warranty

Products are warranted for 2 full years (checking and repairing services) from the date of purchase which products are not being damaged by any man-made factors.

Service outwith the warranty period may incur an extra charge.
For more details please contact Hotowell directly.

REFERENCE:

DOWNLOAD MANUALS:

Hotowell HTW-WF06-FC Smart Touch Screen Thermostat User Manual

Tagged hotowell, hotowell HTW-WF06-FC, HTW-WF06-FC, HTW-WF06-FC Thermostat, screen Thermostat, Smart Touch Thermostat, User Manual

Hotowell HTW-WF06-FC Smart Touch Screen Thermostat User Manual