RDE100.1DHW is a room thermostat that allows you to set the ideal room temperature at the time you want.
In addition, it offers independent control of DHW. There are several switching patterns available that can be set to your specific needs.
You can set the current time of day.
set ok + – mode | Proceed as follows: · Press set and select · Press ok and the time flashes for setting · Press + or – to adjust the time · Press ok to confirm · The weekday flashes, press + or – to select the desired day · Press ok to save the value · Press mode to exit or wait for the program to exit automatically |
mode | Press and hold mode for at least 7 seconds to activate a button lock. Repeat to unlock. The unit operates normally when the buttons are locked, but no changes are possible while the buttons are locked. |
+ – ok set mode | Press + or – to increase or decrease the room temperature setpoint in increments of 0.5 °C / 1 °F. Proceed as follows: · Press + or – to adjust the setpoint temporarily. This adjustment is reset as soon as the operating mode changes. · Press ok, set or mode to save the value or wait for the program to exit automatically · To lock the setpoints, use parameters P06 and P08.
|
mode
! | The thermostat provides Comfort mode, Economy mode, and Auto mode. Changeover between the operating modes can be made manually by pressing mode. Comfort mode is the permanent (24 h) selection of Comfort. Select this mode to maintain Comfort temperature permanently without any time switch. It is used during occupancy periods, for example. Economy mode is the permanent (24 h) selection of Economy. Select this mode to maintain the Economy temperature permanently without any time switch. It is used during non-occupancy periods, for example at night. AUTO In Auto timer mode, operating modes (Comfort, Economy) are changed automatically according to the time switch set.
Note: Frost protection is a function always active in the background. As soon the room temperature falls below 5 ºC, the unit automatically activates the heating . |
set ok + – mode
! | · Press set and select · Press ok to confirm · Press mode to select an operating mode, Comfort or Economy · Press + or – to adjust the setpoint permanently. · Press ok to confirm · Press mode to exit or wait for the program to exit automatically Note: This permanent setpoint is used during Auto timer mode. |
Energy-saving tips without loss of comfort
set ok + – mode
! | Use the Holiday mode to set the thermostat to a constant temperature while absent. · Press set and select · Press ok to confirm · Press + or – to adjust the temperature setpoint · Press ok to confirm · Press + or – to adjust the number of days for holidays (Note: 0 = Holiday mode OFF) · Press ok to save the value · When Holiday mode is activated, the remaining days are displayed on the screen Note: If you press mode while Holiday mode is active, the function is turned off and the symbol disappears. If the Comfort and Economy setpoint values are both locked, the lowest locked setpoint value is the Holiday mode setpoint value. You can adjust the setpoint temperature from 5 ºC up to the lowest locked setpoint value. |
Option 1: Time switch with individual day selection (P11=0)
set
ok
+
–
mode
You can select Comfort or Economy at 15 minute intervals throughout the day. The 0:00 to 24:00 hour time bar allows you to set the operating mode for the selected day(s).
Example:
When Auto timer mode is enabled, changeover between the operating modes is automatic after the settings are saved.
Proceed as follows:
Option 2: Time switch with the same 7 day selection (P11=1)
set ok + – mode
| You can set all the 7 day time switches at the same time. Example: Visible bars: Control to Comfort temperature Invisible bars: Control to Economy temperature Proceed as follows: 1) Set the parameter (P11=1). Please refer to the section “Do you want to change parameters“. 2) Press set and select AUTO. 3) Press ok to confirm. 4) Time switch for period Mon (1) – Sun (7) is displayed. 5) Press ok to initiate time programming. During programming step: 6) Press mode to select an operating mode, (Comfort or Economy) or 7) Press + or – to adjust time setpoint by 15 minutes for the selected mode. 8) Press ok to save the time switch. 9) Press mode or wait for the program to exit automatically. |
Option 3: Time switch with 5-2 day selection (P11=2)
set ok + – mode
| You can set Monday – Friday time switch at once and Saturday – Sunday time switch at once. Example: Visible bars: Control to Comfort temperature Invisible bars: Control to Economy temperature
Proceed as follows: 1) Set the parameter (P11=2). Please refer to the section “Do you want to change parameters“. 2) Press set and select AUTO. 3) Press ok to confirm. 4) Time switch for period Mon(1) – Fri(5) is displayed. 5) Press + or – to select the period, Mon (1) – Fri( 5) or Sat (6) – Sun (7). 6) Press ok to confirm the selected period and initiate time programming. During programming step: 7) Press mode to select an operating mode, (Comfort or Economy) or 8) Press + or – to adjust the time setpoint by 15 minutes for the selected mode. 9) Press ok to save the time switch. 10) Repeat the steps 5-9 for the other period if necessary; or 11) Press mode or wait for the program to exit automatically. |
Default value | Day/s | Comfort mode | Economy mode |
Mo (1) – Fr (5) | 6:00 – 8:00 hr 17:00 – 22:00 hr | 22:00 – 6:00 hr 8:00 – 17:00 hr | |
Sa (6) – Su (7) | 7:00 – 22:00 hr | 22:00 – 7:00 hr |
set ok | You can enter the DHW Auto Time switch as follows: · Press set and select AUTO , then press ok You can select DHW on or off for every 15 minutes interval of the day. The 0:00 to 24:00 hour time bar allows you to set DHW on or off for the selected day(s). Example: Visible bars: DHW control is switched on Invisible bars: DHW control is switched off There are 3 options for DHW Time switch setting: Individual day, 7 day and 5/2 day. To set the DHW Time switch, please follow the same steps as in the section “Do you want to enter your own time switch“. |
Default value | Day/s | DHW control ON | DHW control OFF |
Mo (1) – Fr (5) | 6:00 – 8:00 hr 17:00 – 22:00 hr | 22:00 – 6:00 hr 8:00 – 17:00 hr | |
Sa (6) – Su (7) | 7:00 – 22:00 hr | 22:00 – 7:00 hr |
Symbol
+ – ok mode | If you want to change control parameters, proceed as follows: · Press + and – simultaneously for 5 seconds · Release them and parameter “P01” is displayed on the bottom segment · Press + or – to scroll to the parameter that needs to be adjusted · Press ok to select this parameter · Press + or – to adjust the value · Press ok to confirm the adjusted value · Press mode to exit the parameters without saving or wait for the program to exit automatically |
Parameter no. | Description | Setting range (default) |
P01 | Time format | 1 = 24:00 hours (default) 2 = 12:00 AM/PM |
P02 | Selection of °C or °F | 1 = °C (default) 2 = °F |
P03 | Standard temperature display | 1 = room temperature (default) 2 = setpoint |
P04 | Temperature sensor calibration | -3…3 °C Step 0.5 °C (-6…6 °F, step 1 °F) Default: 0 °C |
P06 | Comfort setpoint lock | 0 = OFF (default) 1 = ON à locked according to setting in permanent temperature setpoint |
P08 | Economy setpoint lock | 0 = OFF (default) 1 = ON à locked according to setting in permanent temperature setpoint |
P09 | Buzzer | 0 = OFF 1 = ON (default) |
P10 | Show frost protection icon | 0 = OFF (default) 1 = ON |
P11 | Time switch type for autotimer and DHW | 0 = individual Days (default) 1= all 7 days 2= 5/2 days |
P12 | Periodic pump run | 0 = OFF (default) 1 = ON |
P13 | DHW timer bar timeout | 0 = no DHW bar 1 = 1 minute (default) 2 = 2 minutes Adjustable range 0 to 15 minutes |
P21 | Button scanning rate for the capacitive buttons Note: a higher scanning rate means shorter battery life. | 0.2 = 0.25 s 0.5 = 0.5 s 1.0 = 1.0 s (default) 1.5 = 1.5 s |
P22 | Reload factory settings | 0 = OFF (default) 1 = reload |
P23 | Software version information | No adjustment possible |
P78 | Control behavior | 0 = On/Off, 1.0K 1 = On/Off, 0.3K 2 = TPI fast 3 = TPI medium 4 = TPI slow (default) |
P89 | Forward shift on max | 0, 0.5,…24 h Default: 0 h |
P90 | Early shutdown max | 0, 0.5,…6 h Default: 0 h |
Download Manual:
SIEMENS RDE100.1 DHW Programmable Room Thermostat Operating Instruction
SIEMENS RDE100.1 DHW Programmable Room Thermostat Operating Instruction
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…