SALUS RT510SR Wireless Programmable thermostat Quick Guide

SALUS RT510SR Wireless Programmable thermostat

Introduction

The RT510SR module will switch your appliance on or off in accordance with the temperature set by you. The completed RT510SR series consists of a transmitter – RT510TX thermostat and a Smart Relay SR868.

Product Compliance

This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of Conformity on www.saluslegal.com 868.0-868.6MHz; <13dBm

Safety Information

Use in accordance with the regulations. Indoor use only. Keep your equipment completely dry. Disconnect your equipment before cleaning it with a dry towel.

Button Functions

1. Press for frost mode
2. Press to enter / exit boost mode
3. Press to enter/exit the permanent override
4. Press to select setting
5. Press 3 sec for holiday mode
6. Increase button
7. Decrease button
8. Test Mode / Pairing Mode
9. Press to confirm the setting

LCD icons

1. Current day of the program
2. Current Temperature
3. Current time
4. Temperature unit
5. Temporary / Permanent Override
6. Frost Protection
7. Vacation Mode
8. Heating Mode ON
9. RF signal
10. Low battery
11. Boost Mode
12. Program number

DIP switch settings

The DIP Switches can be found on the rear of your thermostat.

Control feature	TPI	Span
Operation	When TPI is selected on DIP switch № 2, the DIP switch № 1 is functional. You can choose the Cycles Per Hour between a lower comfort level (6CPH) and a higher comfort level (9CPH).	When Span is selected on DIP switch № 2, the DIP switch № 1 is not functional. The temperature accuracy of your thermostat is set to ± 0.25 °C.

LED indication Smart Relay

LED State		Description
Red	On	The relay is off.
	Flash	The relay is in pairing mode.
Green	On	The relay is on.
	2 x Flash	The relay is writing pairing code.
Red and Green	Flash alternately	The relay is paired but lost link.
	Flash in different sequence	It indicates the software version after reboot.

Installation – Step 1

1. Electric heater
2. Boiler

The thermostat and the smart relay are pre-paired from the factory if purchased as a pack. If not, follow thermostat pairing process.

Installation – Step 2

Pairing process

In case you want to add more than one relay, set all relays into pairing mode, including the ones already paired, and start the pairing process. The LED will flash red when the relay is in pairing mode.

Put the thermostat into pairing mode, by pressing the pair button for 3 seconds. After the smart relay is paired with the thermostat, the LED is steady red.

Test the pairing process

If the thermostat loses connection with the Smart Relay, the Smart Relay goes into fail safe mode after 30 minutes.

Setting hour and day

Continue with the same steps for setting the Day. Press Set to return to the Main Screen.

Temporary override

Permanent override

Setting programs

You can create personalized programs for your controller. You have the option to choose between a 5-2 days program or a daily one by using parameter d04 from Installer mode.

Press SET to change your programs.

Use and to select Weekend/Weekday, press SELECT to confirm your option. Follow the same steps for setting the hour, minutes and temperature. After you have done all the changes, please press SET to confirm all your choices and to return to the Main Screen.

Installer mode

Press the three buttons together for 3 seconds. Use +Hr to select dxx parameter, or to change the parameter or to change parameter value and to confirm.

Parameter

dxx	Function	Parameter	Default value
d01	Temperature display increments	0,1 or 0,5°C	0,5°C
d02	Temperature offset	± 3,0°C	0,0°C
d03	Frost setpoint	5,0 – 17,0°C	5,0°C
d04	Programmer selection	5/2 or 24 hr (7d)	52d

FR/ NL / DE:
support@salus-controls.de
tel: +49 6108 8258515

Head Office:
SALUS Controls Plc
Units 8-10 Northfield Business Park Forge Way,
Parkgate, Rotherham S60 1SD,
United Kingdom
T: +44 (0) 1226 323961
E: sales@salus-tech.com
E: techsupport@salus-tech.com

www.salus-controls.com

SALUS Controls is a member of the Computime Group

Maintaining a policy of continuous product development SALUS Controls plc reserves the right to change the specification, design and materials of products listed in this brochure without prior notice.
For PDF Installation guide please go to www.salus-manuals.com
Issue date: 06 2020
Version: V004

REFERENCE

Download Manual:

SALUS RT510SPE Wireless Programmable thermostat Wiring Diagram

Other manuals

SALUS RT510SR Wireless Programmable thermostat Wiring Diagram

SALUS RT510SR Wireless Programmable thermostat Quick Guide