Salus

SALUS RT310SPE Internet Wireless Thermostat Quick Guide

SALUS RT310SPE Internet Wireless Thermostat

Introduction

The RT310SPE module will switch your appliance on or off in accordance with the temperature set by you. The completed RT310SPE series consists of a transmitter – RT310TX thermostat and a Smart Plug SPE868.
Go to www.salus-manuals.com for the full PDF version of the manual.

Product Compliance

Directives: EMC 2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU, and RoHS 2011/65/EU.
Full information is available on the website www.saluslegal.com

Safety Information

Use in accordance with national and EU regulations. Use the device as intended, keeping it in dry condition.
Product for indoor use only. Installation must be carried out by a qualified person in accordance with national and EU regulations.

Button Functions

  1. Turn on the LCD backlight.
  2. Turn On/Off the Frost Mode
  3. Increase button.
  4. Decrease button.
  5. Test Mode/ Pairing Mode

LCD icons

  1. The thermostat is calling for heat
  2. The thermostat is in frost mode
  3. The thermostat is sending a signal to the smart plug
  4. The low battery indicator icon
  5. Temperature display

DIP switch settings

The DIP Switches can be found on the rear of your thermostat.

Control feature TPI Span
Operation When TPI is selected on DIP switch № 2, the DIP switch № 1 is functional. You can choose the Cycles Per Hour between a lower comfort level (6CPH) and a higher comfort level (9CPH). When Span is selected on DIP switch № 2, the DIP switch № 1 is not functional. The temperature accuracy of your thermostat is set to ± 0.25 °C.

Smart plug LED indication

Installation

  1. Installation – Step 1
    The thermostat and the smart plug are pre-paired from the factory if purchased as a pack. If not, follow the thermostat pairing process.
  2. Installation – Step 2

Thermostat pairing process

  • In case you have more than 1 smart plug, set ALL the smart plugs into pairing mode and start the pairing process. The LED will flash red when the plug is in pairing mode.
  • Put the thermostat into pairing mode, by pressing the pair button for 3 seconds. After the smart plug is paired with the thermostat, the LED is steadily red.
  • Begin pairing process
  • End pairing proces

Test the pairing process

Change temperature

  1. Actual room temperature
  2. Setpoint temperature Note: By changing the Setpoint (desired) temperature, you are permanently altering your temperature.
  3. Two seconds timeout
  4. Actual room temperature

Frost Mode

Frostpoint review

Frost Protection Off

If the thermostat loses connection with the Smart Plug, the Smart Plug goes into fail safe mode after 22 minutes. In this mode you still can operate your Smart Plug manually (by pressing the button on the device).

Installer mode

Press the three buttons together for 3 seconds. Use to select dxx parameter, or to change parameter value and to confirm.

Parameter

dxx Function Parameter Description Default value
d01 Temperature display increments 0.1 or 0.5°C Select temperature display increments 0.5°C
d02 Temperature offset +/-3.0°C Calibrate your thermostat temperature 0.0°C
d03 Frost setpoint 5.0-17.0°C Set the Frost Point Temperature 5.0°C

REFERENCE

Download Manual:

SALUS RT310SPE Internet wireless Thermostat Quick Guide

OTHER MANUALS:

SALUS RT310SPE Internet wireless Thermostat User Manual

SALUS RT310SPE Internet wireless Thermostat Wiring Diagram

SALUS RT310SPE Internet Wireless Thermostat Quick Guide

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago