SALUS RT310SPE Internet wireless Thermostat User Manual

SALUS RT310SPE Internet wireless Thermostat

Introduction

Product Compliance
This product complies with the essential requirements and other relevant provisions of Directives 2014/53/EU and 2011/65/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.saluslegal.com.

Safety Informations

• Before starting installation work and before using the product, read the entire manual.
• The information contained in the instructions is essential for proper functioning.
• To avoid accidents resulting in personal injury and material damage, please follow all safety precautions, specified in this manual.
• The device should not be used by people with limited mental, sensory or mental abilities, without experience, of insufficient knowledge as well as children.
• Do not use an unassembled device (eg without a cover).
• The device may only be opened by a qualified person.
• Keep electrical devices out of the reach of children and ensure that they do not play with it. Children should not be left unattended. If necessary, disconnect the control system for the entire room.
• Do not leave the packaging, cabinet, or any loose parts of the device unattended, as they pose a risk to children.

WARNING!

• Installation must be carried out by a qualified person with appropriate electrical qualifications in accordance with standards and regulations in force in the given country and in the EU.
• Never try to connect the device other than as described in the manual.
• Before assembly, repair or maintenance as well as during any connection works it is absolutely necessary disconnect the mains supply and make sure that the terminals and electric wires are not live.
• The device may not be exposed to extreme temperatures, strong vibrations or subjected to mechanical shock.
• The device should not be used in unfavorable environmental conditions or in rooms where there is a concentration of flammable gases, fumes or dust.
• There may be additional protection requirements for the entire installation that the installer is responsible for maintaining.

Care for the natural environment is of paramount importance to us. The awareness that we manufacture electronic devices obliges us to dispose of used electronic components and devices safely. Therefore the company has received a registration number issued by the Chief Inspector for Environmental Protection. The crossed out symbol the trash can on the product means that the product must not be disposed of with ordinary waste containers. Sorting waste for recycling helps to protect the environment. It is the user’s responsibility to surrender used equipment to a designated collection point for recycling waste from electrical and electronic equipment.

Product Overview

The HTRS230V(30) from SALUS Controls is a digital, wired and surface-mounted (or on a flush-box) non programmable room thermostat, dedicated for surface heating / cooling control, characterized by high thermal inertia. It is connected to the wiring centre. The thermostat does not have the function of creating schedules – it lowers the set temperature via wiring centre after receiving the NSB signal from the weekly thermostat.
The room thermostat works by turning the heating system on and off as needed by measuring the air temperature. When the air temperature drops below the thermostat setting, it turns on the heating, and turns it off when the set temperature is reached.
Setting the thermostat to a higher temperature will not heat up the room faster. How quickly a room heats up depends on the designed heating system, for example the temperature of the heating medium. Likewise, reducing the temperature even more while cooling the room will not result in faster cooling.
By setting the thermostat to a lower setpoint, the room will be controlled at a lower temperature and will save energy.
The best way to find the temperature that is right for you is to set the room thermostat to a low temperature value – let’s say 18⁰C – and then increase it one degree each day until you are comfortable.
Room thermostats need free airflow to sense the temperature and therefore must not be obstructed by curtains or obstructed by furniture. Nearby electrical heating devices, televisions, wall or table lamps, fireplaces or heaters may prevent the correct temperature measurement and thus the correct operation of the thermostat.

PRODUCT ADVANTAGES:

• absolutely silent operation (TRIAC)
• has a PWM control algorithm
• protection of thermostatic valves against stagnation (VP)
• has frost protection mode

Package content

1. RT310 thermostat
2. 2x AA batteries
3. Short instruction
4. Mounting screws

Proper thermostat location

Please note: The ideal position to thermostat mounting is about 1,5m under floor level far from heating or cooling sources. Thermostat can’t be exposed to sunlight or any extreme conditions like for example draft.
Because of fire and explosion risk there is not allowed to use thermostat in atmosphere of explosive gases and flammable liquids (eg coal dust). In case if any of listed dangers occur you have to use additional protection measures – anti-dust and explosive gases (tight cover) or prevent their formation. Furthermore, thermostat can’t be used in condensation of water vapor conditions and be exposed to water action.

Wall mounting

Content used for thermostat mounting:

How to mount the thermostat to the wall:

Connection description

Before you start (first power up)

LCD icon description

1. Heating Mode indication
2. Cooling Mode */Frost protection mode indication
3. RF signal indicator (only in RT310RF)
4. Low battery status
5. Temperature unit
6. Room / setpoint temperature

Button description

1. Turn on the LCD backlight
2. HEAT/COOL * modes change or Frost Protection mode activation (only when HEAT mode is enabled)
3. Increase button
4. Decrease button.

PLEASE NOTE! The LCD screen can be activated by using any button.

First power up sequence and configuration
To power up the thermostat you have to put the batteries inside. Then thermostat will display following sequence:

User settings

Manual mode – changing temperature setpoint
In manual mode, the thermostat maintains a constant temperature set by the user. To set temperature setpoint follow steps below:

Frost protection mode
In this mode the setpoint temperature is automatically set to frost setpoint to prevent pipes from freezing. If the room temperature is lower than the frost setpoint, frost protection will be enabled. To set frost protection mode follow steps below:

The Frostpoint temperature can be reviewed by pressing the UP button once, but can only be changed in Installer Mode. Frost protection mode can be enabled only in HEAT mode.

Sleep mode

In sleep mode thermostat is switched off and doesn’t consume any energy and it is impossible to make an action until you activate the thermostat again. To activate/deactivate sleep mode follow steps below:

TO ACTIVATE SLEEP MODE:

TO DEACTIVATE SLEEP MODE:

Heat/Cool mode *

User can set thermostat for heating or cooling. In HEAT mode thermostat is displaying flame icon all the time. When thermostat is in HEAT mode and thermostat is CALLING for HEAT – the flame icon is flashing. In COOL mode thermostat is displaying snowflake icon all the time. When thermostat is switched to the COOLING mode and the thermostat is CALLING for COOL – then the snowflake icon is flashing. Default mode is HEAT MODE.
NOTE: every time when thermostat need to start call for cooling then it can be delayed for about 3 minutes.
To set selected mode please follow steps below:

HOW TO SET COOLING MODE:

HOW TO SET HEATING MODE:

Temperatures outside operating range
Temperatures below 10 °C are displayed without the leading ‘0’. Temperatures exceeding the measurable range will be indicated by ‘HI’ for temperatures above the upper limit, and ‘LO’ for temperatures below the lower limit, as shown in the images.

Low battery detection

Battery voltage is checked every minute. When the battery voltage drops to a certain level, the Low-Battery warning  indicator appears.

• The thermostat functions normally during low battery. However, user must change the batteries as soon as possible before the battery is too weak for the normal operation to be assured.
• When you change the batteries, you have about 30 seconds to to do so without losing your settings.

Installer mode

To enter installer parameters please follow steps below. Please refer to parameters table description before any changes. Use button to move through parameters. Use or for adjustements. Every change/selection confirm by button.

DETAILED TABLE WITH ALL INSTALLER PARAMETERS:

dxx	Function	Parameter	Default value
d01	Temperature display accuracy	0.1°C or 0.5°C	0.5°C
d02	Temperature offset	+/- 3.0°C	0.0°C
d03	Frost Protection setpoint temperature	5.0°C – 17.0°C	5.0°C

DIP switches parameters
DIP switches are used to set chosen control algorithm. They are located under back cover of the thermostat (please refer to the picture below): The position of the DIP switches determines the type of control algorithm:

1	2	Cooling *	Heating	Default value
ON	ON	Hysteresis +/- 0.25	Hysteresis +/- 0.25
OFF	ON	Hysteresis +/- 1.5	Hysteresis +/- 0.5
ON	OFF	Hysteresis +/- 1.0	TPI 9 CPH
OFF	OFF	Hysteresis+/- 0.5	TPI 6 CPH

PLEASE NOTE! TPI algorithm is recommended for underfloor heating. It can be adjusted between a low comfort level (6 CPH) and a higher comfort level (9 CPH). „CPH” means cycles per hour and it relates to the frequency of the measurement cycles performed by thermostat

Reset function

To RESET RT310 thermostat please follow steps below:

Cleaning and Maintenance

The RT310 thermostat requires no special maintenance. Periodically, the outer casing can be wiped clean using a dry cloth (please DO NOT use solvents, polishes, detergents or abrasive cleaners, as these can damage the thermostat). There are no user serviceable parts within the unit; any servicing or repairs could only be carried out by Salus Controls or their appointed agents.

Technical Informations

Power supply	2 x AA batteries
Rating max	3(1) A
Output signal	NO/COM/NC relay
Temperature range	5 – 35°C
Display temperature accuracy	0.1°C or 0.5°C
Control algorithm	TPI or Hysteresis: ±0.25°C, ±0.5°C,±1.0°C or ±1.5°C
Communication	Wired
Dimension [mm]	96 x 96 x 27

Warranty

SALUS CONTROLS warrants this product to be free from any defects in material or workmanship and to perform as specified for a period of five years from the date of installation. SALUS CONTROLS reserves the sole responsibility for breach of this warranty by repairing or replacing the defective product. This product includes software that matches the distributor’s identification at the time of sale. The manufacturer / distributor provides a guarantee covering all functions and specifics of the product in accordance with this marking. The distributor’s warranty does not cover the correct operation of the functions and features available as a result of a product software update.
The full warranty conditions are available at www.salus-controls.eu

DISTRIBUTOR OF SALUS CONTROLS:
QL CONTROLS Sp. z o.o., Sp. k. Rolna 4, 43-262 Kobielice, Poland
IMPORTER:
SALUS Controls Plc Units 8-10 Northfield Business Park Forge Way, Parkgate Rotherham S60 1SD United Kingdom
www.salus-controls.com
SALUS Controls is a member of the Computime Group.
Maintaining a policy of continuous product development SALUS Controls plc reserves the right to change the specification, design and materials of products listed in this brochure without prior notice.

REFERENCE

Download Manual:

SALUS RT310SPE Internet wireless Thermostat User Manual

OTHER MANUALS:

SALUS RT310SPE Internet wireless Thermostat Quick Guide

SALUS RT310SPE Internet wireless Thermostat Wiring Diagram

SALUS RT310SPE Internet wireless Thermostat User Manual