The thermostat is designed for the control of electric heating devices (Built-in sensors for measuring room temperature and an external sensor for high-temperature protection, to prevent heating device burned due to high temperatures).
In the state of shutdown, the thermostat will turn on the heating device automatically When the room temperature is below 5℃. when the room temperature is above 7℃, the thermostat will turn off the heating device automatically.
Technical data
In the shutdown state, long-press the mode key ” ” and the clock key ” ” for 5 seconds to enter programming mode. you can switch parameters by mode key. After entering the programming mode, press mode key to adjust ” hour” ,then press mode key to adjust “minute”.Press the mode key again to adjust the temperature.
Advanced setting (qualified person preferred)
Press” M “and” “at the same time to enter the model of advanced setting immediately when the thermostat is turned off. The following seven functions can be chosen by the” M “key
Connect the power supply box according to the wiring diagram.
Push the panel up and take it down the panel.
Install the fixed plate of the thermostat in the electrical connection box with screws.
Make the panel buckle to the fixed plate and push it down.
The heating thermostat should be mounted on the wall with air flowing freely around. Warning: The mounting location should not be influenced by another heat source (e.g. sunlight), airflow through doors& windows, or the temperature of the outer wall.
Failure | Handling |
Crash | 1. Check whether the power supply wiring is correct or not. 2. Check the power key. |
LCD display garbled | 1. The shell is deformed after installation and can be reinstalled. |
Display normal No output | 1. Check whether the wiring between the MPU and the power board is damaged. 2. Check whether the null line of the live line is connected wrong. |
Remote failure | Check if the remote control battery has enough power, if not replace the battery. |
Temperature display error | Adjust the panel temperature display by the first option in the Advanced tab. |
Sensor failure | Check the sensor for damageEr1: Built-in sensor disconnected or fault with it. Er2 External sensor disconnected or fault with it. |
ME 88H.03
ME88H.31
ME 88H.16
Thermostat networking steps
Press and hold the up and down keys for about 5 seconds when the thermostat is turned off. When you hear the buzzer ringing 3 sounds, the thermostat enters the distribution network interface. After the screen displays full display(or press the power button to exit)the thermostat has entered the network initialization status. When the WiFi symbol of the thermostat does not flash, it indicates that the connection is successful. Please note that the router or the corresponding WiFi device is turned on and within 5 meters of the thermostat.
Mobile phone networking steps
Before configuring WIFI, please make sure your phone is connected to 2.4GHz WIFI.
China
Foreign
Open the“Tuya Smart ” app and click “Add Device “as shown below.
After clicking” Small Home Appliances”, select “Thermostat” as shown below.
Click” Confirm indicator rapidly blink” as shown below
After entering the WIFI password, press” Confirm” as shown below.
The phone enters the device search and the connection mode is as shown below.
The mobile phone adds the device connects successfully, click” Done” as shown below.
Click on the” Done” button above to enter the control interface as shown below.
Press and hold the up and down button for about 5 seconds while the thermostat is off. When the buzzer sounds 3 times into the distribution network interface, the screen displays full display. At this time (or press the power button to exit) the control panel has entered the network exit state (also the distribution network state).
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Download Manual
MINCO HEAT ME88AH Electric Wireless Heating
MINCO HEAT ME88AH Electric Wireless Heating Thermostat User Manual
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…