Minco Heat M9.716 Touch Screen Period Programming Thermostat Installation Manual

Minco Heat M9.716 Touch Screen Period Programming Thermostat

Touch Screen Period Programming Thermostat

Touch Screen Period Programming Thermostat Weekly circulation, it is possible to set 6 periods called events each day with corresponding pre-set temperatures, also you can select “period control mode” or “manual mode” according to your individual requirements. The thermostat is recommended for the control of electric heating devices or on/off valve actuators used in water-based heating systems.

Selection Table

Technical data

• Voltage： AC230V 50~60Hz
• Power consumption： 2VA
• Setting range： 5℃…90℃
• Limitation range： 5℃…60℃ (factory setting:35℃)
• Accuracy of temperature measurement：0.5~10℃Adjustable, factory setting±1℃
• Ambient temperature： -5~50℃
• Protective housing： IP20
• Housing material： anti-flammable PC

User operation

1. Power key “ ”
   You can turn the on/off thermostat by pressing this key. Also, you can confirm and exit by pressing “ “key when you have completed the setting of every parameter.
2. The increased key” “and the decrease key” ”
   In the period control mode or comfort mode, when you press the increase/decrease key once, the alternate display stops in the bottom right region and the value of the pre-set temperature will increase/decrease 1℃. It will recover the alternate display with no operation for 3 seconds.
3. Time setting key “ ”
   You can adjust the time and week by pressing the key once. If it is pressed, the hour bit flashes. Then you can press “ ” key and ” “key to change its value. When you complete the setting of the hour bit, you can press this keyto to confirm and continue the setting of the minute bit and week bit sequentially. After the completion of time, you can press” “to confirm and exit.
4. Mode selection key” M ”
   You can select period control mode or comfort mode by pressing the key. If you press this key and hold it for 3 seconds, you can enter the mode of period programming.
5. Locking “ ” and unlocking
   When you press  and at the same time and hold for 3 seconds, the thermostat will be locked/unlocked. When it is locked, no operation can be carried out until it is unlocked.

Display symbols

• Manual mode
• Clock-controlled program mode
• Wake-up, event 1
• Leave (am), event 2
• Return (am), event 3
• Leave (pm), event 4
• Return (pm),event 5
• Sleep, event 6
• Heating

Programming: 6-event time and temperature

Press the ” ” key for 5 seconds to begin programming

Advanced setting (qualified person preferred)

You can press “M” and” “and hold for 5 seconds at the same time to enter the mode of advanced setting when the thermostat is turned off. The following seven functions can be chosen by pressing “M”.

Symbol		Setting	or
1	ADJ	Temperature calibration	Adjust measured temperature
2	SEN	Sensor mode	IN: built-in sensor OUT: floor sensor ALL: both sensors (floor sensor is the limit sensor)
3	LIT	Limitation temperature	Adjust limitation value, Limitation range:5℃~90℃
4	DIF	Switching differential	Adjust switching differential
5	LTP	Antifreeze function	Turn on/off the Anti-frozen function
6	PRG	Set vacation mode	2: 5/2 day mode 1: 6/1 day mode 0: 7-day mode
7	RLE	Potential-free output	00: in the same way 01: in a different way
8	DAILY	Potential-free output delay	Change the delay time
9	HIT	Max. Temperature	Max. Limitation temperature setpoint (99℃)
	AFLAC	Reset to factory settings	Programming parameters will be reset to factory settings when the symbol ” —- ” appears

Explanation of symbols

Dimension：(mm)

Mounting steps

1. Release the front cover by inserting a screwdriver into bottom crack
2. Taking the backing plate apart according to following diagram
3. Install the thermostat in electrical connection box with screws
4. Install the housing cover and lock the external frame

Connecting Diagram

Reference

Download Manual:

Minco Heat M9.716 Touch Screen Period Programming Thermostat Installation Manual

Minco Heat M9.716 Touch Screen Period Programming Thermostat Installation Manual