hotowell

Hotowell HTW-GM4 Floor Heating Thermostat User Manual

Hotowell HTW-GM4 Floor Heating Thermostat

Introduction

GM4 is a new intelligent heating thermostat for floor warming. It detects the indoor temperature and displays the corresponding value. This device automatically regulates the heating output on 120V/240V in accordance with the set point and the room temperature. The clock controls the 7-day user schedule. It is accurate and sensitive with high reliability and high performance

Parameters

Power Supply 120VAC/240VAC 50/60Hz Self-consumption <2W
Installation Way 120V electrical box, deep Dimension 120mm ×76mm
Outer Shell Tempered glass +PC Alloy Wiring Wiring +Terminals
GFCI Class A   5mA Output Load 15Amp., resistive
Maximum Power 120VAC/ 1800W , 240VAC/ 3600W Accuracy ±0.1℃(1℉ )

Installation

  • Use a screwdriver to separate the control panel and power board ofthe thermostat, as figure 1 and figure 2 shown.
  • Choose the proper installation location. Installation height is about 41/2 to 5 feet above the floor. For indoor use only.
  • Do not install close to a heat source, such as hot water pipe, heating pipe, wall-mounted light fixture or in direct sunlight.
  • Connect the power wires to Line 1(L) & Line 2(N) wires of the power board, using the connectors provided, as shown on figure 3.
  • Connect the floor heating load wires to the Load 1 & Load 2 wires of the power board, using the connectors, as shown on Figure 3.
  • Connect the floor sensor wire into terminals 1 & 2 behind the power board and tighten the screws with the screwdriver provided in the box.
  • If needed, connect an auxiliary power module into terminals 5 & 6 of the thermostat for remote control. See the drawing below.
  • Install the power board into the electrical box with the 2 screws provided, and then clip & fasten the front control panel into place with the bottom screw.

Wiring Diagram

Buttons and Display

Operation Instruction

ON/OFF settings

  • ON: From the OFF display, slide the ON/OFF side switch up to turn the unit on.
  • OFF: From the ON display, slide the ON/OFF switch down to turn the unit off. It will display OFF.

GFCI Test
When the thermostat is under normal working status, press the GFCI button on the side of the thermostat, then the screen displays GFCI and the thermostat will stop working, GFCI indicator light is ON. Turn off the thermostat and then turn it on again, the GFCI icon will disappear.

Note: GFCI is used to protect the installer from getting shocked. After installation, please test and see if the GFCI function is OK or not.

  • Make sure that the thermostat is under heating mode. Adjusting the target temperature is needed to trigger the thermostat to start heating.
  • Press the GFCI button to test. The screen displays GFCI and the GFCI indicator light is on and the thermostat stops heating. If any of these cases does not happen, please contact the supplier for a replacement.

Local Time Setting
During OFF mode, press S3 to set time and the icon which is blinking is adjustable. Press S1 or S2 to adjust and set value and press S4 to switch to the next setting item. After finishing, press S4 to confirm or wait for 5 seconds to return back to the main interface. During setting, press S3 to return back to the main interface quickly

Working Mode Setting

  • Schedule mode: during normal display, press S3 to switch to schedule mode, the screen displays
  • Energy-saving mode: during normal display, press S4 to switch to energy-saving mode, the screen displays
  • Away mode: during normal display, press S5 to switch to away mode, the screen displays
  • Manual mode: during normal display, press S1 or S2 to switch to manual mode, the screen displays

Mode setting

  • Schedule mode setting: There are 3 kinds of schedule modes for setting: 7days programmable, 5+2 programmable, 6+1 programmable.
  • During normal display, press S3 for 5 seconds to enter into the schedule setting interface.
  • Then press S3 again to switch between 7:0, 5:2, 6:1. After selecting the schedule mode, then press S4 to confirm.
  • The icon blinking is settable. Press S3 to select the Week Day.
  • During setting, press S1 or S2 to adjust the value.
  • Then press S4 to confirm and switch to the next item. A
  • after finishing, press S3 to save the settings and return back to the main interface or wait for 5 seconds without doing anything to save the settings.

The default setting as below

Period 1 2 3 4
Mon.–Fri. start time 5:00 7:00 17:00 22:00
Sat.–Sun. start time 5:00 9:00 17:00 22:00
Target temp 28℃(82℉ ) 24℃(75℉ ) 28℃(82℉ ) 24℃(75℉ )
  • Energy saving mode: during normal display, press S4 to set. Press S1 or S2 to adjust the value and then press S4 to save the settings and return back to main interface.
  • Away mode: During normal display, press S5 for 3 seconds to set.Press S1 or S2 to adjust the value and then press S5 to save the settings and return back to main interface.
  • Manual mode: During normal display, press S1 or S2 to enter into manual mode setting interface an adjust the value by pressing S1 or S2 and then press S4 to save the settings and return back to main interface.

Check temperature
During normal display, press S4 and S5 at the same time to switch and display the ambient and floor temperature.

Lock keys
Under normal display, press S1 and S2 at the same time to lock the keys. The screen displays. After setting, it is invalid to press any button.

Control methods

  • Indoor temperature detected from floor
  • Room temperature detected by the temperature sensor built-in
  • The thermostat takes the room temperature as the current indoor temperature and floor temperature is for floor high-temperature protection inspection.
  • Floor temperature icon
  • Room temperature icon

There are 3 ways to control the thermostat: The thermostat takes floor temperature as its current room temperature; The thermostat takes the temperature detected by a sensor built-in it as its current room temperature; The thermostat takes the temperature detected by sensor built-in it as its current room temperature and the floor temperature as a inspection item to protect the floor. When the room temperature is below the target temperature, the thermostat will start heating and the screen displays When the room temperature is equal to or above the target temperature, the thermostat will stop heating and the icon disappears.

High temperature protection
When the thermostat take the floor temperature as the inspection item, once the floor temperature is above 45℃(113℉ ), the screen displays “FLOOR LIMIT”, and the thermostat will enter into high temperature protection mode, and the thermostat stops heating. When the floor temperature is below 40℃(104℉ ), “FLOOR LIMIT” icon disappears and if the target temperature is higher than the room temperature, the thermostat will start heating.

Remote control

  • When there is signal detected on the terminal of Setback, the thermostat will enter into remote mode.
  • When the room temperature is below the target temperature set on the remote side, the thermostat will start heating, and the screen displays and at the same time, there is output signal on terminal Relout.
  • When the room temperature is above the target temperature set on the remote side, the thermostat will stop heating, and the screen displays and at the same time, there is NO output signal on terminal Relout.

Sensor failure
If there is failure in the sensor, the screen displays “EEE” at the temperature display area and the thermostat stops heating.

℃ and ℉ scale switch
Under OFF mode, press S3 and S4 at the same time to switch the scale between ℃ and℉.

Hidden menu

During OFF mode, press S3 and S5 at the same time to enter into the secret menu. Press S1 or S2 to change the value and input password “1234”, press S5 to confirm. After entering into the hidden menu, press S4 to switch to the next option to set.

No. Parameter Default setting Setting range Note
P1 High-temperature protection temperature 45℃(113℉ ) OF/ 45~95℃(113~203℉ ) OF: Turn off floor temp. protection
P2 Room temperature calibration 0(00) -9.5℃~9.5℃(-16~16℉ )
P3 temperature setback value 2℃(04℉ ) 0.5~10℃(1~18℉ )
P4 Button sound volume 3 OF/1~9 OF: OFF 1~9: volume level
P5 backlight brightness NO NO/OF ON: Always on OF: backlight off if no operation
P6 control method A-F A-F/Air/Flo Air: temp. detected by the built-in sensor is the room temp.

Flo: temp. detected by the floor sensor is the room temp.

P7 Time format 24 12/24 12: 12 hours format

24: 24-hour format

P8 Floor temp. calibration 0(00) -9.5~9.5℃(-16~16℉ )
P9 floor temp. control setback value 1.5℃(03℉ ) 0.5~10℃(01~18℉ )
P10 floor protection temp. setback value 5.0℃(09℉ ) 0.5~10℃(01~18℉ )
P11 Target room temperature during

remote control mode

16.5℃(62℉ ) 5~37℃(41~99℉ )
P12 Reset to factory default 53 0~99 change to 55 and press S3 to reset to factory default.
P13 Room temperature increasing speed during heating 5 0~99 5 means 5*30s=150s, it means the thermostat increase the room temperature every 150s till the actual room temperature.
P14 ℃/℉ OF OC/OF OC:℃ OF: ℉
P15 GFCI detecting level NOR NOR, 1, 2, 3, OFF NOR: Once detected, the thermostat will alarm GFCI.

1,2,3: Delay to alam GFCI OFF: Turn off GFCI.

REFERENCE:

DOWNLOAD MANUALS:

Hotowell HTW-GM4 Floor Heating Thermostat User Manual

Hotowell HTW-GM4 Floor Heating Thermostat User Manual

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago