hotowell HTW-31-KT13T Wireless Thermostat User Manual

hotowell HTW-31-KT13T Wireless Thermostat

General

HTW-31-KT13T wireless thermostat(Transmitter) is used in heating-only or cooling-only systems to maintain selected room temperature. The controller acquires the room temperature with its integrated sensor and maintains the set point by delivering control commands.

Functions

• The large display can be clearly read with the background lighting.
• Four buttons make it easy to use.
• MAN Mode and PRG. Mode
• 4 periods of each day programmable(5+1+1)
• The display shows the set temperature as well as the measured temperature, and time.
• Temperature display in degrees Celsius.

Technical Data

• Thermostat operating voltage: 2 x AAA, alkaline batteries.
• Frequency: 868Mhz/433Mhz
• Channel selection: By programming the thermostat and the receiver.
• Switching options: 5+1+1
• Temperature settings: 5°C ~ 30°C, 0.5°C increments.
• Accuracy: +/- 0.5°C
• Thermostat dimensions: Surface mounted, 135mm x 87.5 mm x 23.2mm.
• Color: White
• IP protection rating: 30.
• Certification: CE/RoHS

Display & Buttons

PRG. Schedule Setting

Long press the PRG button to enter the PRG setting. The weekday is fixed from Monday to Sunday(1~7), and each day has 4 periods(1~4). Each press of the PRG button can into the next item setting. The time and temperature of each period I can be set in the following steps.

1. Press PRG and hold for 3 seconds, the time display flash, and change the value with the + and – buttons. each press is 15mins
2. Press the PRG button, the temperature display flash, and change the temperature with the + and – buttons.
3. Press the PRG button to the next period.
4. The other period settings follow the same way.

Example:

Monday to Friday

Saturday

Sunday

Period

1

2

3

4

1

2

3

4

1

2

3

4

Time

6:30

8:00

18:00

22:30

8:00

10:00

18:00

23:00

9:00

12:00

19:00

0:00

Temp.

21°C

18°C

21°C

16°C

21°C

21°C

21°C

16°C

23°C

21°C

16°C

21°C

• Press and hold the SET button for around 3 seconds. The minute’s display (top left in the display) flashes.
• Change this value using the + and – buttons.
• Press the SET button. The hour display (top left in the display) flashes.
• Change this value using the + and – buttons.
• Press the SET button. The day display (top left in the display) will flash as a number.
• Change this value using the + and – buttons. Use 1 for Monday, 2 for Tuesday, and 3 for
• Wednesday, 4 for Thursday, 5 for Friday, 6 for Saturday, and 7 for Sunday.

Temp. Calibration
Turn the thermostat off, and long-press the SET button to enter Sensor calibration. Range: -8°C~+8°C

• At control centre(HTW-31-X8 ), press KEY button(K1-K8), indicator flashing
• On the thermostat, turn off the thermostat, and hold the “SET” button for 3 seconds, it will show the code on display, then press the “SET” button again,, until the indicator on the control center (LED1-LED8) stops flashing, the code pairing finish.
• You can check if the thermostat and HTW-31-X8 work fine by setting the temp higher than room temp, the system should start heating, and when heating, the LED on HTW-31-X8 will be on, which means the corresponding actuator is working now. ID Pair success.
• If you want to unlink the thermostat and HTW-31-X8 channel, you can power off HTW-31-X8, then power on the HTW-31-X8 and long press the channel KEY button within 1 minute, when you see that Channel on and off, unlink success.

Installation

Transmitter

Mount on the wall: Separate the face plate and base plate, and mount the base plate on the wall with provided screws. After done, hung the face plate on the base plate Put it on a desk: and install the foot directly.

Dimensions

REFERENCE:

DOWNLOAD MANUALS:

hotowell HTW-31-KT13T Wireless Thermostat User Manual

hotowell HTW-31-KT13T Wireless Thermostat User Manual