This is a legacy product document supported by Resideo. It is no longer manufacture
BE CAREFUL! Never use sharp instruments, such as a pencil or pen, to press touchscreen keys. To prevent damage to the thermostat, always press the keys with your fingertip.
This thermostat contains a Lithium battery which may contain Perchlorate material. Perchlorate Material—special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate
Need Help?
For assistance or warranty information please visit http://yourhome.honeywell.com or call Customer Care toll-free at 1-877-492-8466
CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage, do not operate the cooling system when the outdoor temperature is below 50˚F (10˚C).
Congratulations! You’ve just purchased the world’s most advanced, easy-to-use thermostat. It has been designed to give you many years of reliable service and touchscreen climate control.
This thermostat is ready to go!
Your new thermostat is ready to go. Just check the settings below and change if needed:
ONE-TOUCH TEMP CONTROL
You can override the program schedule at any time, and manually adjust the temperature (see page 8).
Press the SYSTEM button to select one of the following, then press DONE.
Press or immediately adjust the temperature. This temporarily overrides the temperature setting for the current time period. The new temperature is maintained only until the next programmed time period begins (please refer to the Home Energy Manager for the program schedule). For example, if you want to turn up the heat early in the morning, it will automatically be lowered later, when you leave for the day.
Auto Changeover: When set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature.
Compressor Protection: This feature forces the compressor to wait a few minutes before restarting, to prevent equipment damage. During the wait time, the message “Wait” is displayed on the screen.
To prevent tampering, the screen can be partially or fully locked. When partially locked, the screen displays SCREEN LOCKED for several seconds if a locked key is pressed. To unlock the screen, press any unlocked key while SCREEN LOCKED appears on the screen. When the screen is fully locked, no keys function. To lock or unlock the screen, see advanced function 0670 on page 17.
Press SCREEN to go to the cleaning screen. Press OK to lock the screen for cleaning. The screen remains locked for 30 seconds so you can clean the screen without disturbing any settings.
After 30 seconds, press DONE to resume normal operation, or press OK if you require more time for cleaning.
Note: Do not spray any liquid directly on the thermostat. Spray liquids onto a cloth, then use the damp cloth to clean the screen. Use water or household glass cleaner. Avoid abrasive cleansers.
The Home Energy Manager Thermostat has a coin cell battery that retains the time during a power failure. Under normal circumstances, the coin cell should last five years. Should the time need to be reset after a power failure, this is an indication that the coin cell needs to be replaced. You should replace the battery every five years, or before leaving home for an extended period The Home Energy Manager Thermostat is shipped from the factory with the coin cell installed. To keep the battery from discharging during shipment and storage, the Home Energy Manager Thermostat is shipped from the factory with a plastic tab inserted in the battery holder. This tab must be removed before the thermostat is mounted on the wall. Simply pull the plastic tab out of the thermostat. To replace the battery, remove the battery tray using a screwdriver. Place a new coin cell (type CR2032 or equivalent) observe the correct polarity and push the battery tray into the battery cover assembly.
If you have difficulty with your thermostat, please try the following. Most problems can be corrected quickly and easily.
Display is blank | • Check circuit breaker and reset if necessary. • Make sure power switch at heating & cooling system is ON. • Make sure furnace door is closed securely. |
No response to key presses (or temperature does not change) | • Check to make sure the thermostat is not locked (see page 10). • Make sure heating and cooling temperatures are set to acceptable ranges: • Heat: 40° to 90°F (4.5° to 32.0°C) • Cool: 50° to 99°F (10.0° to 37.0°C) |
Backlight is dim | • A dim display is normal. The backlight remains ON at a low level, and brightens when a key is pressed. |
Heating or cooling system does not respond | • Press SYSTEM to set system to Heat. Make sure the temperature is set higher than the Inside temperature. • Press SYSTEM to set system to Cool. Make sure the temperature is set lower than the Inside temperature. • Check circuit breaker and reset if necessary. • Make sure power switch at heating & cooling system is ON. • Make sure furnace door is closed securely. • If “Wait” is displayed, the compressor protection timer is ON. Wait 5 minutes for the system to restart safely, without damaging the compressor. |
FCC Compliance Statement (Part 15.19) (USA only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
FCC Warning (Part 15.21) (USA only)
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Interference Statement (Part 15.105 (b)) (USA only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Wireless receiver, remote controller, and outdoor sensor
To comply with FCC and Industry Canada RF exposure limits for general population/ uncontrolled exposure, the antenna(s) used for these transmitters must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Portable Comfort Control
This portable transmitter with its antenna complies with FCC and Industry Canada RF exposure limits for general population/uncontrolled exposure. This device must not be co-located or operating in conjunction with any other antenna or transmitter.
Section 7.1.3 of RSS-GEN
Operation is subject to the following two conditions:
Section 7.1.2 of RSS-GEN
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
http://yourhome.honeywell.com U.S. Registered Trademark. 2011 Honeywell International Inc. 69-2536EFS—03 M.S. Rev. 11-11 Printed in the U.S.A
Download Manual:
Honeywell Home Energy Manager Touchscreen Thermostat Operating Manual
OTHER MANUALS
Honeywell Home Energy Manager Touchscreen Thermostat User Guide
Honeywell Home Energy Manager Touchscreen Thermostat Operating Manual
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…