Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FEATURED

Honeywell Home Energy Manager Touchscreen Thermostat Operating Manual

Honeywell

Honeywell Home Energy Manager Touchscreen Thermostat 

Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-PRODUCT

This is a legacy product document supported by Resideo. It is no longer manufacture

BE CAREFUL! Never use sharp instruments, such as a pencil or pen, to press touchscreen keys. To prevent damage to the thermostat, always press the keys with your fingertip.

 

Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-1

This thermostat contains a Lithium battery which may contain Perchlorate material. Perchlorate Material—special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate

Need Help?
For assistance or warranty information please visit http://yourhome.honeywell.com or call Customer Care toll-free at 1-877-492-8466

CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage, do not operate the cooling system when the outdoor temperature is below 50˚F (10˚C).

Home Energy Manager Thermostat Features

Congratulations! You’ve just purchased the world’s most advanced, easy-to-use thermostat. It has been designed to give you many years of reliable service and touchscreen climate control.

Features

  • One-touch temp control overrides the program schedule at any time.
  • Precise comfort control keeps the temperature within 1°F of the level you set.
  • Large touchscreen display with backlight is easy to read—even in the dark.

This thermostat is ready to go!
Your new thermostat is ready to go. Just check the settings below and change if needed:

  1. Select fan setting: Preset to Auto……………………………………………………. See page 6
  2. Select system setting: Preset to Heat……………………………………………. See page 7

ONE-TOUCH TEMP CONTROL
You can override the program schedule at any time, and manually adjust the temperature (see page 8).

Home Energy Manager Features

Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-2

Quick Reference to Status Display

 

Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-3

Home Energy

 

Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-4

  • Press FAN to select fan operation, then press DONE.
  •  ON: The fan is always on.
  •  Auto: The fan runs only when the heating or cooling system is ON.
  •  Circ: Fan runs randomly, about 35% of the time, not counting any run time with the heating or cooling system

System Settings

 

Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-5

Press the SYSTEM button to select one of the following, then press DONE.

  • Heat: The thermostat controls only the heating system.
  •  Cool: The thermostat controls only the cooling system.
  •  Off Heating and cooling systems are OFF.
  •  Auto: The thermostat automatically selects heating or cooling depending on the indoor temperature.
  •  Em Heat (only for heat pumps with auxiliary heat): Thermostat controls Emergency and Auxilliary Heat

Program Schedule Override (Temporary)

Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-6

Press or immediately adjust the temperature. This temporarily overrides the temperature setting for the current time period. The new temperature is maintained only until the next programmed time period begins (please refer to the Home Energy Manager for the program schedule). For example, if you want to turn up the heat early in the morning, it will automatically be lowered later, when you leave for the day.

Special Features

Auto Changeover: When set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature.
Compressor Protection: This feature forces the compressor to wait a few minutes before restarting, to prevent equipment damage. During the wait time, the message “Wait” is displayed on the screen.

Screen Lock

Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-7

To prevent tampering, the screen can be partially or fully locked. When partially locked, the screen displays SCREEN LOCKED for several seconds if a locked key is pressed. To unlock the screen, press any unlocked key while SCREEN LOCKED appears on the screen. When the screen is fully locked, no keys function. To lock or unlock the screen, see advanced function 0670 on page 17.

Screen Cleaning

Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-8

Press SCREEN to go to the cleaning screen. Press OK to lock the screen for cleaning. The screen remains locked for 30 seconds so you can clean the screen without disturbing any settings.
After 30 seconds, press DONE to resume normal operation, or press OK if you require more time for cleaning.
Note: Do not spray any liquid directly on the thermostat. Spray liquids onto a cloth, then use the damp cloth to clean the screen. Use water or household glass cleaner. Avoid abrasive cleansers.

Home Energy Manage

Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-9

The Home Energy Manager Thermostat has a coin cell battery that retains the time during a power failure. Under normal circumstances, the coin cell should last five years. Should the time need to be reset after a power failure, this is an indication that the coin cell needs to be replaced. You should replace the battery every five years, or before leaving home for an extended period The Home Energy Manager Thermostat is shipped from the factory with the coin cell installed. To keep the battery from discharging during shipment and storage, the Home Energy Manager Thermostat is shipped from the factory with a plastic tab inserted in the battery holder. This tab must be removed before the thermostat is mounted on the wall. Simply pull the plastic tab out of the thermostat. To replace the battery, remove the battery tray using a screwdriver. Place a new coin cell (type CR2032 or equivalent) observe the correct polarity and push the battery tray into the battery cover assembly.

Advanced Functions

  1. Press SYSTEMHoneywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-10
  2. Press and hold blank center key until the display changes.Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-11
  3. Change settings as required
  4. Press DONE to exit & save changes.

Advanced Functions

 

Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-12Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-13Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-14Honeywell-Home-Energy-Manager-Touchscreen-Thermostat-Operating-Manual-FIG-15

Troubleshooting

If you have difficulty with your thermostat, please try the following. Most problems can be corrected quickly and easily.

Display is blank •       Check circuit breaker and reset if necessary.

•      Make sure power switch at heating & cooling system is ON.

•      Make sure furnace door is closed securely.

No response to key presses (or temperature does not change) •      Check to make sure the thermostat is not locked (see page 10).

•       Make sure heating and cooling temperatures are set to acceptable ranges:

•      Heat: 40° to 90°F (4.5° to 32.0°C)

•      Cool: 50° to 99°F (10.0° to 37.0°C)

Backlight is dim •      A dim display is normal. The backlight remains ON at a low level, and brightens when a key is pressed.
Heating or cooling system does not respond •      Press SYSTEM to set system to Heat. Make sure the temperature is set higher than the Inside temperature.

•      Press SYSTEM to set system to Cool. Make sure the temperature is set lower than the Inside temperature.

•      Check circuit breaker and reset if necessary.

•      Make sure power switch at heating & cooling system is ON.

•      Make sure furnace door is closed securely.

•      If “Wait” is displayed, the compressor protection timer  is  ON. Wait  5 minutes for the system to restart safely, without damaging the compressor.

Regulatory information

FCC Compliance Statement (Part 15.19) (USA only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Warning (Part 15.21) (USA only)
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Interference Statement (Part 15.105 (b)) (USA only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Wireless receiver, remote controller, and outdoor sensor
To comply with FCC and Industry Canada RF exposure limits for general population/ uncontrolled exposure, the antenna(s) used for these transmitters must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Portable Comfort Control
This portable transmitter with its antenna complies with FCC and Industry Canada RF exposure limits for general population/uncontrolled exposure. This device must not be co-located or operating in conjunction with any other antenna or transmitter.

Section 7.1.3 of RSS-GEN
Operation is subject to the following two conditions:

  1. this device may not cause interference, and
  2.  this device must accept any interference, including interference that may cause undesired operation of the device.

Section 7.1.2 of RSS-GEN
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
http://yourhome.honeywell.com U.S. Registered Trademark. 2011 Honeywell International Inc. 69-2536EFS—03 M.S. Rev. 11-11 Printed in the U.S.A

Reference

Download Manual:

Honeywell Home Energy Manager Touchscreen Thermostat Operating Manual

OTHER MANUALS

Honeywell Home Energy Manager Touchscreen Thermostat User Guide

Honeywell

Honeywell Home Energy Manager Touchscreen Thermostat Operating Manual

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *