Hexa CONTROL

Hexa CONTROL RT226-F4 FAN COIL THERMOSTAT Installation and operation instructions

Hexa CONTROL RT226-F4 FAN COIL THERMOSTAT

SPECIFICATION

  • Electrical Rating…………………………….…………100~240VAC 50/60HZ
  • Fan Relay Amps inductive………………….….………8A
  • Heat/Cool Relay Amps inductive………………………3A
  • Accuracy…………………………………………….…±0.5°C(1 °F)
  • Set point Temperature Range…………………….….…5℃to 60℃
  • Dimensions………………………………………….…120.9mm×82.9mm×28mm

FEATURES:

  • New vertical design, crosswise installation or vertical installation
  • Temperature adjustments are simple
  • Display shows both set points and room temperature simultaneously
  • Maintains the temperature to within 1 degree set point
  • Auto fan with adjustable 3-fan speed.
  • Permanent user setting retention during power loss, no batteries are required
  • External sensor, Remote control
  • RS485 communication function

IMPORTANT SAFETY INFORMATION:

  • Always turn off power at the main power source by unscrewing fuse or switching circuit breaker to the off position before installing, removing, cleaning, or servicing this thermostat.
  • Read all of the information in this manual before installing this thermostat.
  • Only a professional contractor should install this thermostat.
  • All wiring must conform to local and national building and electrical codes and ordinances.

OPERATION

Thermostat Buttons and Switches

  1. Display area
  2. System button (COOL, HEAT)
    In switch on state, long press this button for 3 seconds, can start or close sleep mode
    In the switch-off state, long press this button for 3 seconds, can enter to menu setting
  3. Fan speed option button (HI MED LOW AUTO)
    In switch on state, long press this button for 3 seconds will enter to switch off timer mode;
    In the switch-off state, long press this button for 3 seconds, will enter to switch on timer mode
  4. Raises temperature setting
  5. Lowers temperature setting
  6. Power button

The Display

  1. Shows working mode
  2. Shows setting temperature
  3. Shows measure temperature
  4. Shows sleep mode
  5. Temperature unit mark
  6. Shows fan speed option
  7. Shows fan rotate in Auto speed
  8. Shows fan speed option
  9. Shows heating output
  10. Shows cooling output
  11. Shows room card mode

INSTALL THE THERMOSTAT

ATTACH THERMOSTAT BASE TO WALL

WARNING: ELECTRICAL SHOCK HAZARD
Turn off power at the main service panel by removing the fuse or switching the appropriate circuit breaker to the OFF position before removing the existing thermostat.

WIRING DIAGRAM

485 Communication Function Instruction

When the 485 communication distance is more than 300m, need to increase terminal resistance in 485 the beginning of the communication terminal and end Especially, if the communication equipment quantity is less in the trunk(less than 22pcs). When increasing terminal resistance, only short circuit the terminal resistance jumper J5 of the thermostat.
Remote Control Optional

CONFIGURATION

The configuration menu allows you to set certain thermostat operating characteristics to your system or personal requirements. S witch off the thermostat, long press button ② over 4 seconds till power on again means you have entered the first configuration menu item There are 6 menu items. Press button ② to change to the next item and press button ④ or ⑤ to select.
In implicit parameter menu mode, long press button ⑥ for 3 seconds, all parameters will back to the initial value.

Step Press buttons Displayed(factory default) Press▲、▼to select Descriptions
1 ② 4 seconds (0) -4—+4 Adjust temperature coefficient
2 (35℃) 20℃—50℃ Select the maximum setting temperature for heating
3 (5℃) 5℃—20℃ Select the minimum setting temperature for cooling
4 (℃) ℃/℉ Temperature unit option
5 (2) 1、2、3 Display backlight option
6 (rd) rd, rE Memorize option before power loss
7 (On) OFF/On Fan stop option
8 (4) 4/2 Control system option
9 (1) 1–255 Communication address
10

(18℃)

10—18℃ Heating mode without a room card temperature
11 (25℃) 25—30°C Cooling mode without a room card temperature
12

(SC)

SC/OC/00 Activate Room Card function mode option
  1. Adjust temperature coefficient from 4 LO to 4 HI
    You can adjust the room temperature display up to 3 higher or lower. Your thermostat was accurately calibrated at the factory but you have the option to change the display temperature to match your previous thermostat.
  2. Select the maximum temperature for heating
    This feature provides a maximum set
    poi nt temperature for heat. The default setting is 35 ℃℃, i t can be changed
    between 20 to 50
  3. Select the minimum temperature for cooling
    This feature provides a minimum set point temperature for cooling. The default setting is 5 ℃℃, i t can be changed between 5 to 20
  4. select temperature unit
    °C or ℉℉, the factory default is °C
  5. Display backlight mode option
    • The light will keep the light off continuously.
    • The display will be on when any button of the thermostat is touched, light off automatically after 10 seconds
    • The display will keep the light on continuously The factory default is 2
  6. Memorize the switch on/off option before power loss
    Using button ④ or ⑤ to select rE or rd rd ””: T he thermostat is switched on or off before power loss, after
    the power supply comes to normal again the thermostat will keep switched off ; rE ”: T he thermostat will Memorize its
    ON or OFF status before power loss. The factory default is Rd
  7. Fan stop option
    Use button ④ or ⑤ to select ON or OFF ”. If you select “O N the thermostat will turn on the fan at a speed
    provided by the Fan Switch and will not stop the fan when there is no call for heat or cool. If you select “OFF”, the
    thermostat will stop the fan when there is no call for heat or cool
  8. Select-control system
    Press button ④ or ⑤ to select 4 or 2. 4 means four pipes; 2 means two pipes. The factory default is 4.
  9. 485 communication address
    The setting range is 1 255, the factory default is 1, press button ④ or ⑤ to select.
  10. Select energy-saving set point for heating
    This feature allows you to set energy-saving set point temperatures for heating. The default setting is 18 ℃℃, It can be changed between 10 to 18
  11. Select energy-saving set point for cooling
    This feature allows you to set energy-saving set point temperatures for cooling. The default setting is 25 ℃℃, It can be changed between 25 to 30
  12. Activate the Window Card function mode option
    This fea ture allows you to select the way to activate the energy-saving mode.
    Select OC to activate the energy mode by opening the circuit.
    Select SC to activate the energy mode by close the circuit.
    Select 00 to cancel the energy mode.

Timer switch on/off function and rela y delay protection function
In switch off state, long press button f or 3 seconds, will enter into set the automatically switch on time, press button ④ or ⑤ to set the time, the time value will raise or low er 0.5 ; In switch on state, long press button for 3 seconds, will enter into set t he automatically switches off time, similarly press the raise button or lower button to set the time value.
In timer switch on/off mode, the setting value is the countdown value. For example: when you set the time val ue is 3.5 in switch on state, your thermostat will switch off automatically after three and a half hours. If the time value is 0, means you have closed the timer switch on/off function. In switch on state, if you have open the timer switch off function, th e LCD will display the timer mark and the remaining time. The thermostat also have relay delay protection, remote control, and 485 communication function.

Universal Thermostat Interface Protocol V1.1

  1. Basic Introduction of Protocol
  2. Data Frame Read of Thermostat
    Command frame(from PC): Read all states of the thermostat
  3. Single Data Frame Read of Thermostat
    Command frame 1• Read thermostat on/off state

Response frame: Command returns when all is done correctly; No response when the operation is wrong, PC will handle it; subsequent sets follow this answer/respond rule

Reference:

DOWNLOAD MANUALS:

Hexa CONTROL RT226-F4 FAN COIL THERMOSTAT Installation and operation instructions

Hexa CONTROL RT226-F4 FAN COIL THERMOSTAT Installation and operation instructions

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago