Drayton LP522 Weekend programmer Thermostat Installation Instruction

Drayton LP522 Weekend programmer Thermostat

INSTALLATION INSTRUCTIONS

PLEASE NOTE: INSTALLATION MUST ONLY BE CARRIED OUT BY A QUALIFIED ELECTRICIAN OR HEATING ENGINEER.
MAKE SURE MAINS INPUT HAS A 3 AMP FUSE.

TECHNICAL DATA

LP241Si, LP522Si & LP722Si PROGRAMMERS LP111Si & LP711Si TIMESWITCHES
Voltage	230V a.c. +10% – 10% 50Hz
Programmer Rating	2 (1) A 230V a.c. each switch
Timeswitch Rating	2 (1) A 230V a.c.
Ambient temp	Operating: 0º to 45ºC Storage: -20ºC to 50ºC
Without mains power	Display: blank Time: always kept Program times: always preserved
Programming resolution	1 minute
Wiring	Fixed wiring only, to comply with current IEE regulations
Maintenance	Must be maintained bya qualified electrician or heating engineer
Pollution degree	2
Software class	2
Ball pressure test temperature	75ºC
Rated impulse voltage	2.5kV

Lifestyle Programmers and Timeswitches conform to the essential requirements of these Directives:

• 2014/30/EU – Electromagnetic Compatibility Directive
• 2014/35/EU – Low Voltage Directive

BEFORE INSTALLATION
First, make sure the mains supply is switched off!

PROGRAMMER ONLY

The programmer must be set to the type of system it is to con-trol. The link on the back of the unit has two settings –Pand G.

• P = a fully pumped and controlled system–allowing heating and hot water to be set separately.
• G = a gravity-fed hot water system – which does not allow independent setting of heating without hot water, though hot water can be controlled alone.

USING AN EXISTING WALL-PLATE

Loosen the securing screws on the old programmer and unplug it. Check that there’s 70mm clearance to the right of the wall-plate, and 25mm above it. Check the chart on the next page to compare terminals and if necessary, change the wiring of the wall-plate to suit. Now plug the Lifestyle unit into the wall-plate and tighten the securing screws.
Check the 3A fuse, and switch on the mains.

FITTINGANEW WALL-PLATE
The ideal location is 1.4m above floor level, with reasonable lighting, good access, no condensation, no extremes of temperature, andasupporting surface that fully covers the back of the unit.
Position with 70mm clearance to the right, 25mm above, and sufficient room to access the securing screws underneath.
Fix, with terminals at the top, either direct toa flat wall using wall plugs and No. 6 x 1” (25mm) woodscrews, or on a flush mount-ing single conduit box type UA1 (BS4662) using M3.5 x 14 bolts. DO NOT USEA SURFACE MOUNTING BOX.

TIMESWITCH TERMINAL COMPARISONS
MAKE	MODEL	Earth	Neutral	Live	Common	On	Off	Spare
	Current Mod	els
Drayton	Tempus 1, 2 (new models)		N	L	1	2	3	4
Drayton Lifestyle	LP111, LP711, LP111Si, LP711Si		N	L	1	2	3	4
Switchmaster	300		N	L	4	1
	Discontinued/Compet	tors’	Mod	els
ACL	TC (Towerchron)		2	1	4	7
Drayton	SM1		N	L	1	2	3	4
Drayton	miGenie Wish 1		N	L	1	2	3	4
Drayton	MiTimeMT711R, MiTime RF Pack1		N	L	1	2	3	4
Drayton	Tempus 1, 2 (old models)		N	L	1	2	3	4
Switchmaster	980		N	L	4	1
British Gas	EMT2, UT1, UT2		N	L	1	3	2	4
Danfoss Randall	TS15, 75 (Mk18)	E	N	L	1	4	2	5/6
Danfoss Randall	TS715, TS715Si		N	L	1	4	2	3
Danfoss Randall	TS975	E	N	L	5	4	6	1,2,3
Danfoss Randall	SET1, SET1E	E	N	L	5	4	6
Danfoss Randall	SET4	E	N	L	5	4	6
Danfoss Randall	103, 103E, 103E5, 103E7	4	5	6	3	1		2
Danfoss Randall	911, 971	E	N	L	5	6	4	2
Grasslin Towerchron	QE1		N	L	2	4
Grasslin Towerchron	T2001, T2001Q	E	N	L		7
Honeywell	ST 6100A, ST 6100C		N	L	1	4	2
Honeywell	ST 7000B		N	L	1	2	3	4
Horstmann	Centaur SC1, SC7			L		3	2
Horstmann	Centaur Plus, C11, C17, C17-ZW		N	L	2	4	3
Horstmann	Emerald 423, Pearl Auto		N	L	2	4	3
Horstmann	517, Coronet, H11, H17	E	N	L	3	4
Landis& Staefa	RWB3		N	L		4	3
Landis& Staefa	RWB30, RWB50, 100, 152, 170		N	L	4	4	3
Landis& Staefa	RWB7	E	N	L	2	4	3
Myson	Mictrotimer (link L-5 and 5-8)		E	N	L	5	4	6
Myson	MEPIC		N	L	1	3	2	4
Potterton Myson	EP4000, 4001, 4002, 5002		N	L	5	4	2
Salus	EP101, SP120		N	L	4	3
Sangamo	M6			E	4	6	3	1
Smiths	Centroller Mk1, Mk2		N	L	3	2
Smiths	Centroller 30		1	2		3/4
Smiths	Centroller 300, 980		N	L	4	1
Sunvic	Select 107, SunProl1000		N	L	1	3	2	4
Sunvic	SP20, SP35		N	L	3	5	4	5
Venner	Vennerette		N	L	LINE	LOAD

PROGRAMMER TERMINAL COMPARISONS

PROGRAMMER TERMINAL COMPARISONS
MAKE	MODEL	Earth	Neutral	Live	Ch1 on	Chl2 on	Ch3 on	Ch4 on
	Current Models
Drayton	Tempus 3, 4, 6,7 (old models), Tempus 6,7		N	L	1	2	3	4
Drayton Lifestyle	LP112, LP241, LP522, LP722		N	L	1	2	3	4
Switchmaster	400, 600 (no connection to terminal 4 on 600)		N	L		4	3	1
Switchmaster	805, 900, 900i		N	L	4	2	3	1
	Discontinued/Competitors’ Models
ACL	MP (Towerchron)		2	1
ACL	FP (Towerchron)		2	1	8	11	6	10
Drayton	SM2		N	L	1	2	3	4
Drayton	miGenie Wish 2		N	L	1	2	3	4
Drayton	MiTime MT721R, MiTimeRF Pack 2 & 3		N	L	1	2	3	4
British Gas	EMP2, UP1, UP2		N	L	1	2	3	4
Danfoss Randall	CP15, CP715, FP15, FP715 (Mk18)	E	N	L	1	2	3	4
Danfoss Randall	3020P, 3060	E	7	6			4	2
Danfoss Randall	4033 (link 1-6)	E	7	6	5	3	4	2
Danfoss Randall	102, 102E, 102E5, 102E7 (link 6-3)	E	5	6			1	2
Danfoss Randall	701 (link L-5 and 5-6)	E	N	L			3	1
Danfoss Randall	702 (link L-5 and 5-6)	E	N	L	4	2	3	1
Danfoss Randall	922, 972 (link L-2 and 2-5)	E	N	L	1	4	3	6
Danfoss Randall	SET2, SET2E, SET3E, SET3M, FP975 SET5 (link L-2 and 2-5)	E	N	L	3	6	1	4
Grasslin Towerchron	DP 72, QE2		N	L	1	2	3	4
Honeywell	ST 699/799 (link L-5 and 5-8)		N	L	7	4	6	3
Honeywell	ST 6200, ST 6300, ST 6400, ST 6450		N	L	1	2	3	4
Honeywell	ST 7100 (link L-3 and 3-6)		N	L	7	4	8	5
Horstmann	525, 527, 425 Diadem, H21, H27, H121, Tiara (link L-2 and 2-5)	E	N	L	3	6	1	4
Landis& Staefa*	RWB2, RWB2E, 20, 40, 102, 200, 252 & 270, RWB9		N	L	1	2	3	4
Myson	Microtimer (link L-5 and 5-8)		N	L	7	4	6	3
Myson	MEP2C		N	L	1	2	3	4
Potterton Myson	All EP2000’s, EP3000’s, EP6000’s (link L-5 and N-N)		N	L	1	2	3	4
Potterton Myson*	Mini Minder		N	L	1	2	3	4
Salus	EP200, SP220		N	L	1	2	3	4
Sangamo	M5 (link 1-6)		N	L			1	8
Sunvic	Select 207, SunPro 2000		N	L	1	2	3	4
Sunvic	SP50, SP100 (link L-3)		N	L	1	4	2	5

Can simply be removed from the backplate and replaced without any disturbance to the existing wiring.

WIRING THE TIMESWITCH

Make the wiring connections as above. Note that the output contacts are voltage-free, so power needs to be put on to Terminal 1 either by linking from Terminal L or from a separate supply with a 3A fuse.

WIRING THE PROGRAMMER
USING A DRAYTON SIMP-L-FIT, ALTHOUGH NOT NECESSARY, WILL MAKE THIS INSTALLATION EASIER.

Other Manuals

 Drayton LP522 Weekend programmer Thermostat User Instruction

Drayton LP522 Life Style LP and LPSi Programmers & Timeswitches Thermostat User Instructionproduct Guide

Drayton LP522 Weekend programmer Thermostat Installation Instruction

Skip to PDF content