Drayton LP522 Weekend programmer Thermostat User Instruction

an explanation for householders
Programmers allow you to set ‘On’ and ‘Off’ time periods. Some models switch the central heating and domestic hot water on and off at the same time, while others allow the domestic hot water and heating to come on and go off at different times.
Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle. On some programmers you must also set whether you want the heating and hot water to run continuously, run under the chosen ‘On’ and ‘Off’ heating periods, or be permanently off.
The time on the programmer must be correct. Some types have to be adjusted in spring and autumn at the changes between Greenwich Mean Time and British Summer Time.
You may be able to temporarily adjust the heating pro-gramme, for example, ‘Override’, ‘Advance’ or ‘Boost’. These are explained in the manufacturer’s instructions.
The heating will not work if the room thermostat has switched the heating off. And, if you havea hot-water cylinder, the water heating will not work if the cylinder thermostat detects that the hot water has reached the correct temperature.

INTRODUCTION

LP111 –a 24hr program, up to3 heating periods each day, and every day the same.
LP711 –a 7-day program, allowing for different timings on each day of the week, up to 3 heating periods each day.
If the engineer hasn’t set your timings for you, your timeswitch will work with a standard program that has been set at the factory. If this doesn’t suit you, it’s very easy to change it –when you’ve read this introductory section, simply turn to the page for your timeswitch model.

Remember:

Make your changes using the SET?, YES/-, and + buttons. on the programmer, found under the bottom flap.
You can’t set ON1 as the last timing before midnight, but you can set OFF3 after midnight– providing it’s not more than 23 hours and 59 minutes after ON1.
You need to set the timings in sequence – i.e. ON1, OFF1, ON2, OFF2, ON3, OFF3. If you get out of sequence, the display will flash a warning.

SWITCHING

ON 1 – start of first timed period
OFF 1 – end of first timed period
ON 2 – start of second timed period
OFF 2 – end of second timed period
ON 3 – start of third timed period
OFF 3 – final switch-off of the day

Note: If the engineer has set your program and timings–you won’t need to do anything else. Just keep this guide inasafe place for future reference.

DAY-TO-DAY VARIATIONS

Sometimes you might need to change the way you use your system temporarily – perhaps due to an exceptionally cold day.
Here’s how to do it– without affecting the timings in your program.

Switching on and off
On the front of the timeswitch there is an Advance/Boost button. It allows you to switch your system either on or off, irrespective of the program. So if the heating is off, and you want warmth now, you can either

Press Advance to switch it on (ADV will be displayed), and it will stay on until the end of the next period. Or if the heating is on and you don’t need it, press Advance and it will go off until the beginning of the next ON period.
Advance will only operate in TIMED or ONCE modes.
Press&Hold Boost to switch on for an extra hour ( & BST will be displayed), then Press again for two ( ) or three ( ) hours. To cancel Boost, Press Boost again ( ). Or if the heating is already on, using Boost will extend the ON time by one, two or three hours.

Over-riding the program

At the side of the display there are four operating modes:

OFF = continuously off.
TIMED = on for up to 3 periods a day.
Once = on for 1 periodaday, from the start of ON1 to the end of OFF3.
On = continuously on.

Use the SELECT button under the flap to change the mode. This won’t alter the timings in your program, which you can return to by selecting TIMED.

THE LP111 24hr ELECTRONIC TIMESWITCH

LP111–a 24hr program, up to 3 heating periods each day, and every day the same.
Want to leaveatiming as it is? Just press SET? and move on to the next one.
If you need to reset your timings to the standard program and start again, press ‘SET’ and ‘+’ together to go back to the pre-set program.

The standard program
Your system will come on for up to 3 heating periods every 24hrs. ON1 starts the first one, OFF1 finishes it, and so on. Notice that ON2 and OFF2 are set to the same time.* This means your system won’t respond, but if you want to activate that middle period or change any other timings– read on.

SWITCHING	STANDARD PROGRAM
SWITCHING	MON-FRI	SAT-SUN
ON 1 – start of first timed period	6.30am	7.00am
*OFF 1* – end of first timed period	8.30am	9.00am
ON 2 – start of second timed period*	12.00pm	12.00pm
*OFF* 2 – end of second timed period*	12.00pm	12.00pm
*ON 3* – start of third timed period	4.30pm	4.00pm
*OFF* 3 – final switch-off of the day	10.30pm	11.00pm

Changing the timings

Press the SET? button and you’ll see ‘SET PROG?’.
Press the YES button, and you’ll see ON1, the start of your first heating period. Adjust it in 1-minute steps using the –and + buttons. If the– and + buttons are held down, the time changes in 10-minute steps.
Press SET?, and you’ll see OFF1, the end of your first heating period. Adjust this in the same way, press SET?, then repeat the procedure for ON2, OFF2, ON3 and OFF3.
When you press SET? after setting OFF3, the timeswitch will return to normal operation.

THE LP711 7-DAY ELECTRONIC TIMESWITCH

LP711–a 7-day program, allowing for different
timings on each day of the week, up to 3 heating periods each day.
Want to leaveatiming as it is? Just press SET? and move on to the next one.
If you need to reset your timings to the standard program and start again, press ‘SET’ and ‘+’ together to go back to the pre-set program.

SWITCHING	STANDARD PROGRAM
SWITCHING	MON-FRI	SAT-SUN
ON 1 – start of first timed period	6.30am	7.00am
*OFF 1* – end of first timed period	8.30am	9.00am
ON 2 – start of second timed period*	12.00pm	12.00pm
*OFF* 2 – end of second timed period*	12.00pm	12.00pm
*ON 3* – start of third timed period	4.30pm	4.00pm
*OFF* 3 – final switch-off of the day	10.30pm	11.00pm

Changing the timings

Press the SET? button and you’ll see ‘SET PROG?’.

Set all weekdays
First you set the times that are going to be the same for each weekday, then you can select each day individually and make any further adjustments. If you want each day to be quite different, go straight to ‘Set each day’.

Press the YES button, and the display will ask ‘SET MON to FRI PROG?’.
Press YES and you’ll see ON1, the start of your first heating peri-od. Adjust it in 1-minute steps using the– and + buttons.
If the–and + buttons are held down, the time changes in 10-minute steps.
Press SET?, and you’ll see OFF1, the end of your first heating period. Adjust this in the same way, press SET?, then repeat the procedure for ON2, OFF2, ON3 and OFF3.

Set each day

If, after you’ve set OFF3 you want to fine-tune one or more weekdays, press SET? until you find the first day you want to adjust – then go through the procedure, altering any time you wish. Press SET? to move on to the next day. When you’ve finished, press SET? until you see ‘SET SAT SUN PROG?’.
If you don’t want to alter any individual days, keep pressing SET? until you see ‘SET SAT SUN PROG?’.

Set weekend

Press YES and alter ON1, OFF1, ON2, OFF2, ON3 and OFF3 times in the same way.

Set each day

If, after you’ve set OFF3 for both SAT & SUN, you want to fine-tune Saturday or Sunday, press SET? until you find the first day you want to adjust – then go through the procedure, altering any time you wish. Press SET? to move on to the next day. When you press SET? after setting your hot water for Sundays, the pro-grammer will go back to normal operation.
If you don’t want to alter either day, keep pressing SET?until the programmer goes back to normal operation.

If the engineer has set your program and timings–you wont need to do anything else. Just keep this guide inasafe place for future reference.

INTRODUCTION

Lifestyle programmers will automatically switch your central heating and hot water on and off at times that suit you. Depending on your system, central heating and hot water can either both come on and off at the same time, or work independently. The red light on the front of the programmer shows whem each one is on

There are 4 models in the Lifestyle range:

LP112 –a 24hr program, with linked central heating and hot water on for up to 3 heating periods each day, and every day the same.
LP241 –a 24hr program, with central heating and hot water working independently for up to 3 heating periods each day, and every day the same.
LP522– a 5/2-day program allowing for different timings at the weekends, with central heating and hot water working independently for up to3 heating periods each day.
LP722 –a 7-day program allowing for different timings on each day of the week, with central heating and hot water working independently for up to 3 heating periods each day.

If the engineer hasn’t set your timings for you, your programmer will work with a standard program that has been set at the factory. If this doesn’t suit you, it’s very easy to change it –
when you’ve read this introductory section, simply go to the section that contains your programmer model.

Remember:

Make your changes using the SET?, YES/-, and + buttons on the programmer, found under the bottom flap.
You can’t set ON1 as the last timing before midnight, but you can set OFF3 after midnight– providing it’s not more than 23 hours and 59 minutes after ON1.
You need to set the timings in sequence – i.e. ON1, OFF1, ON2, OFF2, ON3, OFF3. If you get out of sequence, the display will flash a warning.

SWITCHING

ON 1 – start of first timed period
OFF 1 – end of first timed period
ON 2 – start of second timed period
OFF 2 – end of second timed period
ON 3 – start of third timed period
OFF 3 – final switch-off of the day

The engineer has set your program and timings–you won’t need to do anything else. Just keep this guide in a safe place for future reference.

DAY-TO-DAY VARIATIONS

Sometimes you might need to change the way you use your central heating or hot water temporarily – perhaps due to an unusually cold day, or exceptional demand for hot water. Here’s how to do it–without affecting your program.

Switching on and off

On the front of the programmer there are two Advance/Boost buttons– one for central heating and one for hot water. They allow you to switch your system either on or off, irrespective of the program. So if the heating or hot water is off, and you want warmth or hot water now, you can either

Press Advance to switch it on (ADV will be displayed), and it will stay on until the end of the next period. Or if the heating/hot water is on and you don’t need it, press Advance and it will go off until the beginning of the next ON period. Advance will only operate in TIMED or ONCE modes.
Press & Hold Boost to switch on for an extra hour( & BST will be displayed), then Press again for two ( ) or three ( ) hours. To cancel Boost, Press Boost again ( ). Or if the heating/hot water is already on, using Boost will extend the ON time by one, two or three hours.

Over-riding the program

On each side of the display there are four operating modes –one group for central heating, the other for hot water. You can change modes with immediate effect by using the appropriate SELECT button. This won’t alter the timings in your program, which you can return to by selecting TIMED.

OFF = continuously off.
TIMED = on for up to 3 periods a day.
ONCE = on for 1 period a day, from the start of ON1 to the end of OFF3.
ON = continuously on.

THE LP112 24hr ELECTRONIC PROGRAMMER

LP112–a 24hr program, with linked central heating and hot water on for up to 3 heating periods each day, and every day the same.
If the timings haven’t been set for you, then your programmer will still be on the factory-set standard 24hr program, with central heating and hot water operating together on the same settings for every day of the week. But it’s easy to make changes–just follow the instructions.
Want to leaveatiming as it is? Press SET? and move on to the next one.
If you need to reset your timings to the standard program and start again, press ‘SET’ and ‘+’ together to go back to the pre-set program.
If you don’t press anything for two minutes, the programmer automatically goes back to normal operation.

The standard program
Your system will come on for up to 3 heating periods every 24hrs. ON1 starts the first one, OFF1 finishes it, and so on. Notice that on the standard program ON2 and OFF2 are set to the same time.* This means your system won’t respond, but if you want to activate that middle period, or change any other timings– read on.

SWITCHING	STANDARD PROGRAM
ON 1 – start of first timed period	6.30am
*OFF 1* – end of first timed period	8.30am
ON 2 – start of second timed period*	12.00pm
*OFF* 2 – end of second timed period*	12.00pm
*ON 3* – start of third timed period	4.30pm
*OFF* 3 – final switch-off of the day	10.30pm

Changing the timings

Press the SET? button and you’ll see ‘SET PROG?’.
Press the YES button, and you’ll see ON1, the start of your first heating period. Adjust it in 1-minute steps using the – and + buttons. If the– and + buttons are held down, the time changes in 10-minute steps.
Press SET?, and you’ll see OFF1, the end of your first heating period. Adjust this in the same way, press SET?, then repeat the procedure for ON2, OFF2, ON3 and OFF3.
When you press SET? after setting OFF3, the programmer will return to normal operation.

THE LP241 24hr ELECTRONIC PROGRAMMER

LP241–a 24hr program, with central heating and hot water working independently for up to 3 heating periods each day, and every day the same.
If the timings haven’t been set for you, then your programmer will still be on the factory-set standard 24hr program, with central heating and hot water operating together on the same timings for every day of the week. But it’s easy to make changes, and have heating and water working independently – just follow the instructions.
Want to leaveatiming as it is? Press SET? and move on to the next one.
If you need to reset your timings to the standard program and start again, press ‘SET’ and ‘+’ together to go back to the pre-set program.
If you don’t press anything for two minutes, the programmer automatically goes back to normal operation.

The standard program

Your system will come on for up to3 heating periods every 24hrs. ON1 starts the first one, OFF1 finishes it, and so on. Notice that on the standard program ON2 and OFF2 are set to the same time for both central heating and hot water.*This means your system won’t respond, but if you want to activate that middle period, or change any other timings– read on.

SWITCHING	STANDARD PROGRAM
SWITCHING	CH	HW
ON 1 – start of first timed period	6.30am	6.30am
*OFF 1* – end of first timed period	8.30am	8.30am
ON 2 – start of second timed period*	12.00pm	12.00pm
*OFF* 2 – end of second timed period*	12.00pm	12.00pm
*ON 3* – start of third timed period	4.30pm	4.30pm
*OFF* 3 – final switch-off of the day	10.30pm	10.30pm

Changing the timings

Press the SET? button and you’ll see ‘SET PROG?’.

Set the central heating

Press the YES button, and the display will ask ‘SET CH PROG?’.
Press YES and you’ll see ON1, the start of your first central heat- ing period. Adjust it in 1-minute steps using the – and + but-tons. If the – and + buttons are held down, the time changes in 10-minute steps.
Press SET?, and you’ll see OFF1, the end of your first central heating period. Adjust this in the same way, press SET?, then repeat the procedure for ON2, OFF2, ON3 and OFF3.

Set the hot water

When you press SET? after setting OFF3 for the central heating, the display will ask ‘SET HW PROG?’.
Press YES, then set your times in the same way. Remember, in this mode you can have different times to your central heating if you wish.
When you press SET? after setting OFF3 for the hot water, the programmer will return to normal operation.

THE LP522 5/2-DAY ELECTRONIC PROGRAMMER

LP522 – a 5/2-day program allowing for different timings at the weekends, with central heating and hot water working independently for up to 3 heating periods each day.
If the timings haven’t been set for you, then your programmer will still be on the factory-set standard program. This means that central heating and hot water will operate together, with the same timings for weekdays and different ones for the weekend. But it’s easy to make changes, and have heating and water working independently – just follow the instructions.
Want to leave a timing as it is? Press SET? and move on to the next one.
If you need to reset your timings to the standard program and start again, press ‘SET’ and ‘+’ together to go back to the pre-set program.
If you don’t press anything for two minutes, the programmer automatically goes back to normal operation.

The standard program
Your system will come on for up to 3 heating periods every 24hrs. ON1 starts the first period, OFF1 finishes it, and so on. Notice that ON2 and OFF2 are set to the same time.* This means your system won’t respond, but if you want to activate that middle period, or change any other timings – read on.

SWITCHING	WEEKDAYS		WEEKENDS
SWITCHING	HW	CH	HW	CH
*ON 1* – start of first timed period	6.30am	6.30am	7.00am	7.00am
*OFF* 1 – end of first timed period	8.30am	8.30am	9.00am	9.00am
*ON 2* – start of second timed period*	12.00pm	12.00pm	12.00pm	12.00pm
*OFF 2* – end of second timed period*	12.00pm	12.00pm	12.00pm	12.00pm
ON 3 – start of third timed period	4.30pm	4.30pm	4.00pm	4.00pm
*OFF* 3 – final switch-off of the day	10.30pm	10.30pm	11.00pm	11.00pm

Changing the timings

Press the SET? button and you’ll see ‘SET PROG?’.

Set the weekday central heating

Press the YES button, and the display will ask ‘SET CH MON to FRI PROG?’.
Press YES and you’ll see ON1, the start of your first central heating period. Adjust it in 1-minute steps using the – and + but-tons. If the – and + buttons are held down, the time changes in 10-minute steps.
Press SET?, and you’ll see OFF1, the end of your first central heating period. Adjust this in the same way, press SET?, then repeat the procedure for ON2, OFF2, ON3 and OFF3.

Set weekday hot water

When you press SET? after setting OFF3 for the central heating, the display will ask ‘SET HW MON to FRI PROG?’.
Press YES, then set your times in the same way. Remember, in this mode you can have different times to your central heating if you wish.

Set weekend central heating

When you press SET? after OFF3 for the weekday hot water, the display will ask ‘SET CH SAT SUN PROG?’. Press YES to confirm, and alter the times in the same way.

Set weekend hot water

When you press SET? after OFF3 for the weekend central heating, the display will ask ‘SET HW SAT SUN PROG?’. Press YES, and follow the procedure.
When you press SET? after OFF3 for HW SAT SUN, the programmer will go back to normal operation.

THE LP722 7-DAY ELECTRONIC PROGRAMMER

LP722 – a 7-day program allowing for different timings on each day of the week, with central heating and hot water working independently for up to 3 heating periods each day.
If the timings haven’t been set for you, then your programmer will still be on the factory-set standard program. This has central heating and hot water operating together – with the option of having different timings for each day of the week. But it’s easy to make changes, and have heating and water working independently – just follow the instructions.
Want to leave a timing as it is? Press SET? and move on to the next one.
If you need to reset your timings to the standard program and start again, press ‘SET’ and ‘+’ together to go back to the pre-set program.
If you don’t press anything for two minutes, the programmer automatically goes back to normal operation.

SWITCHING	WEEKDAYS		WEEKENDS
SWITCHING	HW	CH	HW	CH
*ON 1* – start of first timed period	6.30am	6.30am	7.00am	7.00am
*OFF 1* – end of first timed period	8.30am	8.30am	9.00am	9.00am
*ON 2* – start of second timed period*	12.00pm	12.00pm	12.00pm	12.00pm
*OFF 2* – end of second timed period*	12.00pm	12.00pm	12.00pm	12.00pm
*ON 3* – start of third timed period	4.30pm	4.30pm	4.00pm	4.00pm
*OFF 3* – final switch-off of the day	10.30pm	10.30pm	11.00pm	11.00pm

Changing the timings

Press the SET? button and you’ll see ‘SET PROG?’.

Press the YES button, and the display will ask ‘SET MON to FRI PROG?’.
Press YES and the display will ask ‘SET CH MON to FRI PROG?’.
Press YES, and you’ll see ON1, the start of your first central heating period. Adjust it in 1-minute steps using the – and + buttons. If the – and + buttons are held down, the time changes in 10-minute steps.
Press SET?, and you’ll see OFF1, the end of your first central heating period. Adjust this in the same way, press SET?, then repeat the procedure for ON2, OFF2, ON3 and OFF3.
When you press SET? after setting OFF3 for the weekday central heating, the display will ask ‘SET HW MON to FRI PROG?’.
Press YES, then set your hot water times in the same way. Remember, in this mode you can have different times to your central heating if you wish.

Set each day

If, after you’ve set OFF3 for your hot water, you want to fine-tune one or more weekdays, press SET? until you find the first day you want to adjust – then go through the procedure, altering any time you wish. Press SET? to move on to the next day. When you’ve finished, press SET? until you see ‘SET SAT SUN PROG?’.
If you don’t want to alter any individual days, keep pressing SET? until you see ‘SET SAT SUN PROG?’.

Set weekend

Press YES, and alter the central heating and hot water times in the same way.
When you press SET? after OFF3 for HW SAT SUN, the programmer will ask the question TEST? If you want to test your program, see below, otherwise press SET? again. If you don’t want to test your program, press SET? again – and you’ll be asked the question SET H’DAY? If you want to set a holiday switch off, see page 23, otherwise press SET? again.If you’re not going to program in a holiday switch-off, then press SET? again and your programmer will go back to normal operation.

Test your program

This test facility allows you to run through your program to check that the timings are exactly what you want.
Answer YES to TEST? and the display will show Monday and a time just past midnight. Press YES again and hold it down –and the display will start to run through the days of the week, pausing for a few seconds when it reaches an ON or an OFF time. At each pause, the appropriate lights and circuits will come on.
Release the YES button, and the display will stop running and give you longer to identify a timing.
Press YES once more, and the display will start running again – and will continue all through the week until you press SET?
Press SET? and your programmer will go back to normal operation.
Remember – The display shows the strict time sequence, so ON1 for HW could be followed by ON1 for CH, then OFF1 for HW etc Using this feature you can program your system

SET A HOLIDAY SWITCH-OFF

Applicable to all models.
Using this feature you can program your system to switch off while you’re on holiday, then switch back on again in time to have the house warm for your return.

Press SET? three times and you’ll see ‘SET H’DAY?’
Press YES to SET H’DAY? and the display will show ‘00’.
Using + and -, set the number of days you want the system to be off.
Press SET, the display will show ‘H’DAY’ and the programmer will switch off the system. It will then return to normal operation after the set number of days.
Remember – The programmer counts each pass through midnight as a day. So if on a Saturday morning you don’t want the heating on again until Tuesday morning, set for 3 days.

SETTING THE CLOCK AND DATE
Applicable to all models.

SETTING THE CLOCK
The clock in your programmer has been set at the factory, and automatically accounts for British Summer Time. However, should you need to set the clock, read on.

Press the SET? button until you see SET CLOCK?.

Set the hour

Press YES once, and then the hour will start to flash. Use the and + buttons to set the hour, checking for AM and PM.

Set the minute
Press SET?, and the minutes will start to flash. Use the – and + buttons to set the exact time.

Press SET?, and ‘SET DATE?’ appears in the display. If you don’t want to change the date press SET? to go back to normal operation. If you do, go on to the next section.

SETTING THE DATE
The weekday is automatically calculated from the date, so if the weekday is incorrect you’ll need to reset the date.

Press the SET? button until you see SET DATE?.

Set the year

Press YES and the year will start to flash. Use the – and + buttons to adjust.

Set the month

Press SET? and the month will start to flash. Use the – and + buttons to adjust.

Set the day

Press SET? and the day will start to flash. Use the – and + buttons to adjust.

Set the Day Light Saving

Press SET? and the current DLS status will start to flash for day light saving (British Summer Time). Use the – and + buttons to turn on or off.
Press SET? to go back to normal operation.

WIRING THE PROGRAMMER

Connection Charts

Make the wiring connections, as above, for the appropriate system.
For surface wiring, snap out the cable entry strip on the bottom edge of the wall-plate. Lifestyle units are double-insulated and need no earth connection, but an earthing continuity (loop) terminal is provided for convenience.
After wiring, plug in the unit and tighten the securing screws.
Check the mains input has a 3A fuse, and switch on the mains. Then set the timings as shown in the User’s Guide.
ALWAYS SWITCH OFF THE MAINS BEFORE REMOVING THE LIFESTYLE TIMESWITCH/PROGRAMMER – AND NEVER FIT IT TO A LIVE WALL-PLATE!

Technical Helpline:

0333 7000 622
Email: [email protected]
Web: www.draytoncontrols.co.uk

Reference

Other manuals: Drayton LP522 Weekend programmer Thermostat Installation Instruction

Drayton LP522 Life Style LP and LPSi Programmers & Timeswitches Thermostat User Instructionproduct Guide

Drayton LP522 Weekend programmer Thermostat User Instruction

View Fullscreen

Tagged Drayton, LP112, LP241, LP3, LP522, LP72, LP722, Programmer, Thermostat, User Instruction, Weekend

Drayton LP522 Weekend programmer Thermostat User Instruction