WUNDATRADE

WUNDATRADE E03 Programmable Thermostat User Manuals

WUNDATRADE E03 Programmable Thermostat

Over View

To turn on/off: Press on/off buttonfully until it clicks to alternate between on/off

Set day of the week and the time
Press the clock button for 5 seconds. A number between 1 to 7 will start flashing indicating day of the week number.
1 = Monday 7 = Sunday. Use the up and down buttons to change to the correct day of the week.
Confirm your choice by pressing the clock button. The time will then start flashing – use theup and downbuttons to change as required and confirm by pressing clock button.
Repeat the same when the minutes start flashing and again confirm by pressing clock button.

Choose either a 5, 6 or 7 day cycle
The programmer offers you the choice of 6 individual on/off events per day of the week with the choice of different temperatures in each event – either for 5 days of the week plus all day heating on days 6 and 7 (the weekend).
OR the same on/off timing for days 1 – 6 plus day 7 with all day heating.
OR the same 6 on/off events for all 7 days. The programmer is set at the factory for the 5 day plus 2 day event cycle.

Copying the 1- 5 settings for 6 or all 7 days 
PRESS ON/OFF BUTTONTO TURN OFF then press and hold menubutton whilst switching on, you are now in advanced settings. Now pressmenu button once to reach PrG – you can now set days 6 or days 6 & 7 to be the same as days 1- 5 by pressing buttons. When the screen shows day 6 with days 1 – 5 OR days 6 & 7 with days 1- 5 you are finished. Switch unit OFF and back ON using clock button to return to main screen.

Set the on off times days 1- 5
To start programming press the menu button for 5 seconds – the sunrisesymbol and 1-5 will appear on the left hand side of the screen together with the time that the first event will start. You can change the time by using the up and down buttons as required and confirm by pressing the menubutton.

Next is the temperature you require during the first period session – use the up and down arrow buttons until satisfied and then confirm by pressing the menu symbol. There are 6 on and off times to input and 6 temperature settings to confirm – if you make a mistake press the menu button repeatedly and go through the complete cycle again until you return to the required place.

Function

Manual override mode
Press menu button until hand symbol appears. The scheduled period is overridden, set the temperature to your individual requirements using up and down buttons and the thermostat will operate at this temperature continuously until manual mode is cancelled by pressing menu button.

Clock controlled programme mode.
Press menu button until clock symbol appears.

&single period comfort mode 
While in clock controlled mode press buttons until the clock and hand symbols appear together. This enables you to manually override the scheduled time period temperature setting, so the temperature can be temporarily changed for a single event, the ‘comfort mode’ temperature is reset at the next event when the thermostat will return to the scheduled program.

Keylock.
Once settings are complete to engage keylock anti-tampering function. Pressbuttons together for 5 seconds to lock or unlock the button keypad.

Programming: 6 on/off event Time & Temperature

Please note:
If using an external floor probe to limit floor temperature, then advanced settings ‘SENSOR MODE’ must be set to ‘ALL’ and the ‘MAX TEMPERATURE’ be set to the desired limit temperature, i.e. 270C for wood flooring.

Advanced settings

Turn the thermostat OFF by pushing the ON/OFFbutton. Then press and hold menubutton while turning the thermostat back on (by pushingsymbol once) until the thermostat enters the ‘advanced settings’ mode. Pressmenu button to advance to the required function. Press button to change individual
function settings. To save settings and EXIT this mode, press ON/OFFbutton.

Key/ symbol to open No. of times to press Symbol Function

 

 

 

 

 

 

 

 

 

 

1

SEN

Sensor Mode

IN     : Built in sensor – shows & ONLY measures air temp OUT : Flood sensor – shows & ONLY measures probe temp

(can be in floor or probe housing)

ALL : Both sensors – shows air temp or set probe temperature (can be in floor or probe housing)

2 PRG

Set Weekly Sequence

2:  5/2 day mode 1:  6/1 day mode 0: 7 day mode
3 HI Max Temperature Max: Limitation temperature setpoint (99OC) (Probe limit temperature, i.e. 270C for wood floors)
4 LO Min Temperature min: Limitation temperature setpoint (4OC)
5 ADA 30 min Preheating mode Adaptive Function On: preheating 30mins early Off: cancel adaptive function
6 ADJ Temperature Calibration Adjust measured temperature
7 ECE Monitoring of energy consumption Total switch-on time in percentage in the last 3 days
8 FAC Reset to factory settings Press for 5 seconds until “—” is shown to restore factory settings

 

 

N/A This Model

 

 

DEA

 

 

 

Auxiliary potential-free output

00: O/P when the thermostat is switched on. 01: O/P together with main loop.

02: O/P built in sensor control main loop floor sensor control auxiliary loop 03: O/P, NOP 30s alternately by the main loop

05: O/P 5mins, NOP 10 mins in turn 10: O/P 10mins, NOP 20mins in turn 15: O/P 15mins, NOP 30 mins in turn

N/A This Model

Bar

Model selection

YES: RTC75.7XXT NO: RTC75.7xx

NOTE: If “ERR” is displayed on the screen when the thermostat is first turned on – enter advanced settings (as described above) and advance to function “2SEN” . Press symbol so that “IN” reads on the screen. Switch the unit OFF and back ON to clear and the thermostat will return to normal working.
Most other adjustments should be made by a qualified person.

Tech support opening hours are subject to change – please visit our website for the latest information
www.wundatrade.co.uk
0800 083 2677

Reference

Download Manual:

WUNDATRADE E03 Programmable Thermostat User Manuals

WUNDATRADE E03 Programmable Thermostat User Manuals

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago