Venstar T6900 Touchscreen Digital Thermostat Owner Manual

Venstar T6900 Touchscreen Digital Thermostat

Get To Know Your Thermostat

Dropdown Dashboard
The Dropdown Dashboard displays temperature, humidity, and other readings. It will also show the high and low readings of the day.

Care and Use of Your Thermostat
Pencils, pens and other sharp objects should never be used on your ColorTouch thermostat; these may damage your touchscreen. Only use your finger tip to press the touchscreen buttons.

DO NOT USE ABRASIVE CLEANERS OR CLEANERS THAT CONTAIN SOLVENTS. DO NOT SPRAY ANYTHING DIRECTLY ONTO THE THERMOSTAT.

Quick Start – Temperature, Modes & Fan

Selecting Your Desired Temperature and Mode

AUTO-CHANGEOVER MODE – Pressing the WARMER or COOLER buttons in Auto mode will adjust both the heat and cool setpoints simultaneously. To adjust heat and cool setpoints individually, choose HEAT mode to adjust the heat setpoint and COOL mode to adjust the cool setpoint, then return to AUTO mode.
HEAT OR COOL MODE – Pressing the WARMER or COOLER buttons in Heat or Cool mode will adjust only the heat or cool setpoints.

Using the Fan Button

Press FAN Icon
FAN ON fan runs constantly except in OFF Mode.
FAN AUTO fan only runs with a heating or cooling demand. Note: FAN button is disabled during Program Run Mode.

Override

Using the Override Button 
NOTE: Override may only be used when the thermostat is set to Program RUN or Holiday ON modes.

Unoccupied Operation – During programmed, unoccupied periods, pressing the OVERRIDE button will force the thermostat into Occupied 1 settings. When the OVERRIDE button is pressed, a timer screen will appear and allow the user to choose from 30 minutes to up to 4 hours of override time.
To turn off the override timer, press the OVERRIDE button and when the timer screen appears, press CANCEL OVERRIDE.
Occupied Operation – During programmed, occupied periods, pressing the OVERRIDE button will force the thermostat into an unoccupied period for the rest of the day. During this forced unoccupied period the OVERRIDE button will operate as described above.
Holiday Operation – During Holiday Mode, pressing the OVERRIDE button will force the thermostat into Occupied 1 settings. When the OVERRIDE button
is pressed, a timer screen will appear and allow the user to choose from 30 minutes to up to 4 hours of override time. To turn off the override timer, press the OVERRIDE button and when the timer screen appears, press CANCEL OVERRIDE.

Set Time & Date

NOTE: When the thermostat is connected to the Skyport; the Time & Date are automatically synchronized to the Skyport Cloud, including automatic Daylight Savings adjustments.

Setting the Time

Main Menu Buttons – Schedule

Edit My Schedule
Adjust Mode, Start Time, Stop Time, and Heat and Cool Se points to desired settings. The Time Period May also be Enabled or Disabled. Uncheck the enabled box for Time Periods you don’t want to use. Press DONE when finished.

 

Fan Settings

The fan may be set to run continuously during Heat, Cool, Auto, and Occupied modes. A Preoccupancy Fan Purge schedule may also be set.
Press to turn fan On to run continuously or Auto for fan to run only with heating or cooling.

Screensaver

The Screensaver allows you to create custom slideshows.

Press this button to preview your screensaver operation before returning to the Home Screen.
After the preview, press anywhere on the screen to return to the sub-menu.

Alerts

The alerts let you know when your system needs service.

Display

The display brightness options may be adjusted in this menu.

When calibration is complete, the thermostat will automatically restart and return to the Home Screen.

Preferences

You may set the type of background that appears on the thermostat Home Screen.

Humidity

The Humidity feature allows the thermostat to control a humidifier or use your air conditioner to dehumidify the space.
IMPORTANT: Aux Output Usage must be set for Hum or Dehum for these settings to take effect. See: AUX Output Settings in the Installation Settings menu.

Holidays

The Holiday Schedule allows the Color Touch Screen to follow a fully customizable preset, weekly, monthly, and yearly holiday program. The thermostat will stay in Unoccupied settings while Holiday is active.

Start by selecting a Holiday.
You may continue to select more holidays or you can press the Repeat button for recurring holidays.
Pressing a selected holiday will deselect that holiday.

Using the Repeat Button
Choose to repeat the holiday every week, month or year. Or, press CANCEL to go back.
If you choose to repeat the holiday every week, you will be prompted to confirm the day of the week to be repeated.

Using the Info Button
Press the Info button to view how non-holidays, holidays, and exceptions to repeating holidays will appear on the Holiday calendar.

Edit Holidays
Deselecting Holidays
You may deselect a holiday simply by pressing on it.
Press BACK to save your changes and return to the Holiday menu.
If you choose to deselect a holiday that is part of a Custom Repeating Program, the screen below will appear. Marking Non-Holidays
You will now be prompted to mark this day only as a non-holiday or edit All repeating holidays that affect this day.
Press SAVE to mark only this day as a non-holiday.
If you choose to edit repeating holidays
that affect this day, press NEXT and the next screen will appear.

Editing Repeating Holidays
If, for example, you choose to repeat the holiday every month, the following screen will appear:
You may now choose to repeat the holiday:

• On the 25th of every month
• On the 4th Monday of every month
• On the last Monday of every month
  Press SAVE to save your changes and return to Holiday programming.

You may now delete all repeating custom holidays in this group by pressing the ON box to uncheck your selection. Press SAVE to return to Holiday editing screens.

Preset Holidays
You may choose from several standard preset holidays to observe. When the preset holidays are set to ON, they will be observed every year on that date.

Overriding Holiday Mode
You may override Holiday Mode by pressing the OVERRIDE button and choosing the amount of override time desired.

Turning Off Holiday Mode From The Homescreen
You may turn off Holiday Mode by pressing the MODE button and then pressing the Holiday STOP button. Security

Security settings may be
set to limit or prevent changes to your thermostat.

Information

This button contains valuable service and system runtime information.

Settings

Thermostat heating and cooling options are found in this menu

Smart Recovery turns on the heat before the Occupied start time to bring the room temperature to the Occupied setpoint at the start of the Occupied time period. Please allow 4-8 days for Smart Recovery time to adjust. When used with a heat pump, electric strip heat will be disabled while Smart Recovery is active.

Dealer Information
A Dealer may enter their company contact information for the customer to use when they need service. This will appear when the “Who To Call For Service” button is pressed in the Information Menu.

Use the keyboard to enter your information.

• Dealer Name
• Contact Name
• Dealer Phone
• Dealer Email
• Dealer Website

Please use ColorTouch Assistant to add Dealer’s logo. (See Page 45)

Upgrade Firmware
Press to upgrade the thermostat firmware. The SD Card must be in the thermostat SD Card reader and contain the valid firmware. If an error message appears, confirm with ColorTouch Assistant that firmware is
up to date or simply try reinserting the SD card.
If you are connected to Skyport Wi-Fi and you receive an Alert that new firmware is available, simply press the Upgrade Firmware button to upgrade wirelessly. Note: Occasionally an update that requires a large amount of data is not possible to do wirelessly. In this case an update using an SD card will be required.

Accessory Info
It is here that you will find helpful information regarding the connectivity status of your thermostat, including the thermostat’s ID.

Setup
Upon pressing setup, the thermostat will search for available local networks with which to connect. After indentifying local access points, you will be promted to choose a network, enter a password and other network options.

Emergency Heat

The Emergency Heat function is only available if your thermostat is set to control a Heat Pump.
To initiate the Emergency Heat feature, Press the Emergency Heat button. During Emergency Heat operation the thermostat will turn on the fan and auxiliary stages of heat when there is a demand for heat. The 1st stage of heating and all stages of cooling will be unavailable. To exit Emergency Heat, press the Emergency Heat button.

The TouchScreen Assistant
ColorTouch Assistant may be downloaded at no charge at: www.venstar.com/thermostats/colortouch/assistant 

Every time the user runs the ColorTouch Assistant software, it automatically connects to Venstar ColorTouch website in the background and updates the software and firmware (the operating system for ColorTouch) at no cost.
The ColorTouch Assistant allows you to use your computer to:

• Upload photos for background and slideshow images
• Configure installation settings
• Update thermostat firmware
• Program a time period schedule
• Upload dealer and service contact information and company logo

The TouchScreen Assistant

Uploading Photos and Settings to your thermostat
When you are finished adding and editing photos and settings, click on Save to SD. When prompted, remove the SD card from the SD card reader on your computer.

At the thermostat:
Insert the SD card into the SD Card Slot

Your thermostat will automatically save your new photos and settings in it’s internal memory. When finished, you may remove the SD card. It is not needed for normal thermostat operation.

Installation Instructions

Remove and Replace the old thermostat
To install the thermostat properly, please follow these step-by-step instructions. If you are unsure about any of these steps, call a qualified technician for assistance.

• Assemble tools: Flat blade screwdriver, wire cutters and wire strippers.
• Make sure your Heater/Air Conditioner is working properly before beginning installation of the thermostat
• Carefully unpack the thermostat. Save the screws, any brackets, and instructions.
• Turn off the power to the Heating/Air Conditioning system at the main fuse panel. Most residential systems have a separate breaker for disconnecting power to the furnace.
• Remove the cover of the old thermostat. If it does not come off easily, check for screws.
• Loosen the screws holding the thermostat base or subbase to the wall and lift away.
• Disconnect the wires from the old thermostat. Tape the ends of the wires as you disconnect them, and mark them with the letter of the terminal for easy reconnection to the new thermostat.
• Keep the old thermostat for reference purposes, until your new thermostat is functioning properly.

Wire Connections
If the terminal designations on your old thermostat do not match those on the new thermostat, refer to the chart below or the wiring diagrams that follow.

Wire from the old thermostat terminal marked	Function	Install on the new thermostat connector marked
G or F	Fan	G
Y1, Y or C	Cooling	Y1
W1, W or H	Heating	W1/0/B
Rh, R, M, Vr, A	Power	R
C	Common	C
O/B	Rev. Valve	W1/O/B*
W2	2nd Stage Heat	W2
Y2	2nd Stage Cooling	Y2
W3	3rd Stage Heat	W3/AUX
HUM	Humidification	W3/AUX
DEHUM	Dehumidification	W3/AUX
S1/OUT –	Temp Sensor	SENSOR
S2/OUT +	Temp Sensor	SENSOR

The ColorTouch Thermostat Backplate
NOTE:
The backplate does not fully cover a full size vertical junction box. The ACC-WPLWH ColorTouch Wallplate or a single-gang, horizontally mounted junction box would be needed for that type of installation

To remove the thermostat backplate:
Using the Finger Pull Areas, pull the front housing away from the backplate.

• W3/AUX 3rd stage heat circuit/2nd stage aux heat/humidification/dehumidication
• W2 2nd stage heat circuit/1st stage aux heat
• W1/O/B 1st stage heat circuit/reversing valve
• Y2 2nd stage compressor relay
• Y1 1st stage compressor relay
• G fan relay
• R 24 VAC return
• C 24 VAC common
• SENSOR remote/outdoor/supply/return sensor connections

Explanation of Thermostat Dip Switches
Dip switches are located on the back of the thermostat

• This dip switch configures the thermostat to control a conventional gas/electric system or a heat pump. If your system is anything other than a heat pump, leave this switch set for GAS/EL.*
  *For some commercial heat pumps, this switch may need to be set for GAS/EL. Consult the commercial heat pump literature.
• When the GAS/EL or HP dip switch is configured for HP, this dip switch (O or B) must be set to control the appropriate reversing valve. If O is chosen, the W1/O/B terminal will energize in cooling. If B is chosen, the W1/O/B terminal will energize in heating.
• When GAS/EL or HP is set for GAS/EL:
  This switch (GAS or ELEC) controls how the thermostat will control the Fan (G) terminal in heating mode. When GAS is chosen, the thermostat will not energize the Fan (G) terminal in heating. When ELEC is chosen the thermostat will energize the fan in heating.
• When GAS/EL or HP is set for HP:
  This switch (GAS or ELEC) defines the Aux Heat type. When GAS is chosen, the auxiliary heat will not be allowed to run during heat pump operation.
  When ELEC is chosen, up to two stages of auxiliary strip heat will be allowed to run.

Sample Wiring Diagrams with Dip Switch Positions Conventional Heating and Cooling Systems

Outdoor Sensor: ACC-TSEN Temperature Sensor 10K ohm sensor at 77F/25C. Negative Temperature Coefficient.

Indoor Remote Sensor with Override Button: ACC-TSENWB Temperature Sensor 10K ohm sensor at 77F/25C. Negative Temperature Coefficient.
(see page 41 for sensor setup instructions)

Humidification
AUX Output Usage must be set for Hum

Dehumidification
AUX Output Usage must be set for Dehum

Troubleshooting

• SYMPTOM: The thermostat touchscreen buttons are not responsive. CAUSE: The touchscreen is out of calibration.
  REMEDY: Remove the thermostat from the backplate. Push the thermostat back onto the backplate, while keeping your finger pressed firmly against the center of the touchscreen, until the Calibration screen appears. Re-calibrate the Touchscreen.
• SYMPTOM: The display is blank.
  CAUSE: Lack of proper power.
  REMEDY: Make sure the power is on to the HVAC and that you have 24vac between R & C.
• SYMPTOM: The air conditioning does not attempt to turn on.
  CAUSE: The cooling setpoint is set too high.
  REMEDY: Lower the cooling setpoint or lower the cooling set-point limit. See Setpoint Limits (page 30).
• SYMPTOM: The heating does not attempt to turn on.
  CAUSE: The heating setpoint is set too low.
  REMEDY: Raise the heating setpoint or raise the heating set-point limit. See Setpoint Limits (page 30).
• SYMPTOM: When controlling a residential heat pump, and asking for cooling, the heat comes on.
  CAUSE: The thermostat reversing valve dip switch is set for “B”. REMEDY: Set the reversing valve jumper for “O”.
• SYMPTOM: When calling for cooling, both the heat and cool come on. CAUSE: The thermostat equipment dip switch is configured for “HP” and the HVAC unit is a Gas/Electric.
  REMEDY: Set the equipment dip switch for “Gas”.
• SYMPTOM: Air handler control board fuse blows when the thermostat
  is attached to the backplate with power on, but does not blow until the thermostat is placed onto the backplate.
  CAUSE: The Outdoor sensor and/or sensor wiring is shorted. REMEDY: Check/replace Outdoor sensor and/or sensor wiring.

Warranty

One-Year Warranty – This Product is warranted to be free from defects in material and workmanship. If it appears within one year from the date of original installation, whether or not actual use begins on that date, that the product does not meet this warranty, a new or remanufactured part, at the manufacturer’s sole option to replace any defective part, will be provided without charge for the part itself provided the defective part is returned to the distributor through a qualified servicing dealer.
THIS WARRANTY DOES NOT INCLUDE LABOR OR OTHER COSTS incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of either defective parts or replacement parts. Such costs may be covered by a separate warranty provided by the installer.

THIS WARRANTY APPLIES ONLY TO PRODUCTS IN THEIR ORIGINAL INSTALLATION LOCATION AND BECOMES VOID UPON REINSTALLATION.
LIMITATIONS OF WARRANTIES – ALL IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY) ARE HEREBY LIMITED IN DURATION TO THE PERIOD FOR WHICH THE LIMITED WARRANTY IS GIVEN. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE MAY NOT APPLY TO YOU. THE EXPRESSED WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON WHATSOEVER.

ALL WORK UNDER THE TERMS OF THIS WARRANTY SHALL BE PERFORMED DURING NORMAL WORKING HOURS. ALL REPLACEMENT PARTS, WHETHER NEW OR REMANUFACTURED, ASSUME AS THEIR WARRANTY PERIOD ONLY THE REMAINING TIME PERIOD OF THIS WARRANTY.
THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR:

1. Normal maintenance as outlined in the installation and servicing instructions or owner’s manual, including filter cleaning and/or replacement and lubrication.
2. Damage or repairs required as a consequence of faulty installation, misapplication, abuse, improper servicing, unauthorized alteration or improper operation.
3. Failure to start due to voltage conditions, blown fuses, open circuit breakers or other damages due to the inadequacy or interruption of electrical service.
4. Damage as a result of floods, winds, fires, lightning, accidents, corrosive environments or other conditions beyond the control of the Manufacturer.
5. Parts not supplied or designated by the Manufacturer, or damages resulting from their use.
6. Manufacturer products installed outside the continental U.S.A., Alaska, Hawaii, and Canada.
7. Electricity or fuel costs or increases in electricity or fuel costs for any reason whatsoever including additional or unusual use of supplemental electric heat.
8. ANY SPECIAL INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE WHATSOEVER. Some states do not allow the exclusion of incidental or consequential damages, so the above may not apply to you.
   This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.

REFERENCE:

Download Manual: 

Venstar T5900 Touchscreen Digital Thermostat Quick Setup Guide

other manuals

Venstar T6900 Touchscreen Digital Thermostat Quick Setup Guide

Venstar T6900 Touchscreen Digital Thermostat Owner Manual