The User Setup Wizard guides you through the XL824’s User configurable settings.
To complete the Setup Wizard and connect the XL824 to Nexia™ Home Intelligence, you need:
Accessing the User Setup Wizard
To access the User Setup Wizard, press MENU > SETTINGS > USER SETUP WIZARD.
When the Setup Wizard is activated, the process cannot be cancelled. The Wizard will guide you through the following steps:
Network Setup
Select your wireless network and enter your password. If your wireless network is available but not shown in the list, select Hidden Network, and manually enter your network’s name (SSID).
NOTE: Wireless Setup is not required when the XL824 is hard-wired to your home network.
Home networking troubleshooting tips can be found at www.nexiahome.com/trane.
Nexia™ Home Intelligence Registration (requires Internet connection)
The Temperature Control Panel is where target temperatures are manually set and adjusted. Press in the INDOOR TEMPERATURE area to reveal the Temperature Control Panel. Use the UP and DOWN arrows to manually adjust the target temperature. Press in the INDOOR TEMPERATURE area again to commit the changes and hide the Temperature Control Panel. With Scheduling Disabled, the new target temperature is permanently set and will remain in effect until it is changed again or a 1-Touch Preset is activated. See “Configuring 1-Touch Presets” on page 13 for more information. With Scheduling Enabled, the new target temperature is set and, by default, will hold until the next scheduled period occurs. The Hold Until time is displayed on the Home Screen. To make the new temperature permanent when Scheduling is Enabled, press HOLD PERM after setting the new temperature. See “Overriding Schedules” on page 12 for more information. To display and edit the current schedule, press SHOW SCHEDULE when Scheduling is enabled.
Changing Period Start or End Times
Changing Period Set Points
Changing the Period Name
The XL XL824 Smart Control is capable of adjusting the temperature settings throughout the day according to a user-programmable schedule.
Each day of the week can have its own unique schedule and each day can have a maximum of six Periods.
Important: Scheduling must be enabled before a schedule can be defined. To verify that Scheduling is enabled, navigate to MENU > SETTINGS > SCHEDULES and verify that ENABLED is highlighted.
To set or modify schedules, navigate to MENU > SCHEDULES or select SHOW SCHEDULES from the Temperature Control Panel.
Periods define the time of day when the target temperature is adjusted. Each day can have from 1-6 Periods, and each day can have different number of periods. The Scheduling Screen shows the start time for each Period highlighted across the top row.
Note: These functions require Scheduling to be enabled. To enable Scheduling, go to MENU>SETTINGS>SCHEDULES and select ENABLE.
Hold Until
Follow these steps to override a schedule until a specified time.
Hold Permanently
Follow these steps to permanently override a schedule. The changes you make will be held until you cancel the hold.
Cancelling an Override
To cancel Permanent Hold or Hold Until, follow these steps.
Touch Presets provide predetermined Heating and Cooling Set Points for Home, Away and Sleep time periods.
Note: 1-Touch Presets requires Scheduling to be disabled. To disable Scheduling, go to MENU>SETTINGS>SCHEDULES and select DISABLE.
When scheduling is disabled, heating and cooling set points are maintained indefinitely. When a temperature change is desired, the user must manually adjust the XL824 Control to the new setting.
Configuring 1-Touch Presets
When enrolled to a Nexia™ Home Intelligence account, the XL824 is a Z-Wave security-enabled device that can serve as a central hub for an entire network of home automation devices and can display local weather conditions, fiveday forecasts and National Weather Service warnings and alerts. See the section on Including Z-Wave Devices for more information on taking advantage of this functionality.
A basic Nexia™ Home Intelligence account subscription is included with the XL824 Control at no additional charge.
Note: Adding additional devices may add charges to your Nexia™ Home Intelligence account. To create your Nexia™ Home Intelligence account go to www.NexiaHome.com/trane.
Your XL824 is designed to integrate seamlessly with Nexia™ Home Intelligence as part of a complete Z-Wave home automation system. If you do not have a Z-Wave bridge on your account, the XL824 will automatically configure itself as your Z-Wave bridge. If you already have a Z-Wave bridge on your account, the XL824 will automatically function as a Z-Wave repeater, improving your system’s communication quality. See the section titled Z-Wave Repeater for additional information.
Including Z-Wave Devices
Excluding Z-Wave Devices
Advanced Z-Wave Functions
Press ADVANCED for advanced Z-Wave functions including unregistering your bridge.
In existing Z-Wave networks already configured with a Z-Wave bridge, the XL824 Control will automatically configure itself as a Z-Wave repeater. See the section titled Including/ Excluding Z-Wave Devices for additional information on using the XL824 Control as a Z-Wave bridge. When the XL824 Control is functioning as a Z-Wave repeater, the Z-Wave Repeater Screen allows you to exclude the XL824 Control from the network and to unregister the device from your account.
Exclude from a Network
Press this button to remove the Z-Wave repeater from your Z-Wave network. This button is used in conjunction with the exclude button on the standalone Z-Wave bridge
Unregister
Press UNREGISTER to unregister this XL824 Control from your account. This will disconnect the XL824 from your account and remove the repeater from your Z-Wave network.
Security setting options on the 824 Control are Off, On and Guest Access. To access the Security Settings, press MENU>SCREEN LOCK.
Automatic Software Upgrades
When the XL824 is connected to a Nexia™ Home
Intelligence account, software upgrades will
occur automatically and do not require user
intervention.
Manual Software Upgrades
The software may also be manually upgraded.
This procedure requires a computer with an Internet connection, a USB Flash Drive, and the included USB connector. From your computer, go to www.Trane.com/residential and select Thermostat & Controls. Click on the XL850, select Download the Latest Version Software and follow the on-screen prompts.
Smart Optimization
The 850 Control is equipped with Smart Optimization. By executing a series of the blower and active call on/off tests, Smart Optimization will customize the 850 Control to each unique environment and increase the accuracy of the sensed indoor temperature and overall system performance.
Smart Optimization is enabled by default and will automatically execute approximately 18 hours after initial power-up. Smart Optimization takes 90 minutes to complete and during the process,heating and cooling operations are disabled.
The screen will indicate that the 850 Control is in Smart Optimization mode.
To delay Smart Optimization for an additional 18 hours, touch the 850 Control Screen and hold for five seconds.
To disable Smart Optimization altogether, navigate to Home>Smart Optimization and select Disable and press Apply.
To enable Smart Optimization, navigate to Home>Smart Optimization and select Enable and press Apply. Smart Optimization will execute in approximately 18 hours.
To manually trigger Smart Optimization, first disable, then re-enable the feature.
INFORMATION TO USER
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ICC NOTICE
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
The manufacturer has a policy of continuous product and product data improvement and it reserves the right to change design and specifications without notice.
Representative-only illustrations included in this document.
Download Manual: Trane XL824 Smart Control Thermostat User Guide
https://device.report/energystar/2336674
Trane XL824 Smart Control Thermostat – Energy Star Certification
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…