NOTE: Read the entire instruction manual before starting the installation.
Improper installation, adjustment, alteration, service, maintenance, or use can cause explosion, fire, electrical shock, or other conditions which may cause death, personal injury, or property damage. Consult a qualified installer, service agency, or your distributor or branch for information or assistance. The qualified installer or agency muse use factory–authorized kits or accessories when modifying this product. Refer to the individual instructions packaged with the kits or accessories when installing.
Follow all safety codes. Wear safety glasses, protective clothing, and work gloves. Have a fire extinguisher available. Read these instructions thoroughly and follow all warnings or cautions included in the literature and attached to the unit. Consult local building codes and the current editions of the National Electrical Code (NEC) NFPA 70. In Canada, refer to the current editions of the Canadian Electrical Code CSA C22.1.
Recognize safety information. This is the safety–alert symbol
The P710U–21NHP, whether configured for A/C or HP application, may be wired with or without connecting a common wire between the indoor equipment and the thermostat. However, it is recommended to use a common wire whenever possible. Without a common wire, batteries must be installed. However, battery power will be supplemented by “power stealing.” This means the thermostat will steal a small amount of power from the equipment to which it is connected. This will also keep it powered while changing the batteries.
NOTE: Not all HVAC equipment is compatible with power–stealing type thermostats. Consult the system equipment Installation Instructions before applying this thermostat in a power stealing manner.
If both batteries and 24VAC operation are used (batteries installed and the common wire connected), indefinite clock operation is provided. The battery will be used only during AC power loss, preserving battery life.
Step 1: Thermostat Location
Thermostat should be mounted:
Thermostat should NOT be mounted:
Step 2: Install Thermostat
IMPORTANT: Install batteries last to ensure proper thermostat mounting and latch engagement.
WARNING: ELECTRICAL SHOCK HAZARD
On power up, the LCD readout will display AC, as this is the default equipment type.
Step 3: Set Thermostat Configuration
Configuration options allow the installer to configure the thermostat for a particular installation. These selections are intended to be made at installation and normally are not modified by the homeowner. Below is a list of available options followed by a description of each one.
Press and hold FAN button for approximately 10 sec until room temperature disappears and the display reads “01”. You are now in configuration mode.
NOTE: If the FAN button is pressed again, or if no button is pressed for 3 minutes, the thermostat will exit configuration mode and return to normal operation. To re-enter configuration mode, the FAN button must be pressed and held for 10 sec again. While in the configuration mode, the temperature display is used to show both the option number and the selected choice within each option. Each press of the MODE button alternates between the option number and the selection within that option. When the configuration mode is first entered, option 01 is displayed. The UP and DOWN buttons now move between the available option numbers. Once an option number is selected, press the MODE button once to display the currently selected choice within that option. The UP and DOWN buttons now move between the available choices within that option. After the new choice is made, press the MODE button again to return to the option number display. When finished with option selections, press FAN button once to exit the configuration mode.
Option 01: Equipment Type
Selections: HP, AC, PH, or PC
Meanings:
PH or PC selects PTAC units (Packaged Terminal Air Conditioners) that are used in motel rooms and other rented spaces. When this option is selected, the display shows only the setpoint, not the room temperature. Also the compressor time guard is disabled, allowing the compressor to turn on immediately when a demand is established.
HP or PH controls 1 speed heat pump with 1 stage of aux heat. AC or PC controls 1 speed air conditioner with one stage of heat.
Option 03: Fahrenheit/Centigrade Selection
This selection operates the thermostat in either Fahrenheit or Centigrade.
Option 04: G (fan) ON with W(Heat) Selection
This selection determines whether the fan (G) is to be ON or OFF when W (furnace or strip heat) is ON. Furnaces and fan coils which manage their own blowers do not require a separate G signal. Some auxiliary heaters require a separate G signal to operate the blower when W is applied.
Option 10: Reversing valve
Option 13: Room Air Temperature Offset
Selections:
The number of degrees to be added to the displayed temperature to calibrate or deliberately miscalibrate the measured room temperature. The selected number is the number of degrees, plus or minus, which will be added to actual temperature. This option is in •F even if Option 3 is set for _C.
Option 15: Auto Changeover
Selections: ON, OF — Default is OF.
The heat setpoint and cool setpoint are separated by a minimum of 2 degrees. This feature allows the thermostat to automatically change between heating and cooling mode when a demand has been present in the opposite mode for a period of 20 minutes. Manually changing either the cooling or the heating setpoint will allow an auto changeover to occur without the 20 minute time constraint.
Temperature Display
Thermostat will display room temperature until UP or DOWN button is pressed. The words SET TEMP appear when these buttons are pressed, and the current setpoint is displayed. If no buttons are pressed for 5 seconds, the display will change back to show room temperature.
Backlighting
Continuous backlighting is not available. The backlight will come on for 10 seconds after any button press. Without AC power and when the battery is low, the backlight will remain off with button presses.
Battery Indicator
A battery indication icon on the display shows nothing, half, or low/no battery condition. If the battery is full or operation is from AC power, no icon appears. Under battery operation, if the battery is half full, a half full battery icon appears. As the battery depletes below half, the icon remains at half, but the 10 second backlight disappears. When the battery is absent or depleted, the display goes blank except for an empty battery icon and all outputs are turned off.
Timeguard Timer
A 5–minute timeguard is built into the thermostat immediately upon power–up, and any time the compressor turns off. The compressor will not turn on until the timeguard has expired. The timeguard affects only compressor operation. Pressing UP andFAN buttons simultaneously will override the timeguard for 1 cycle. With PH or PC selected under Option 01, this timer is defeated.
Cycle Timer
In normal heating and cooling operation the thermostat will not allow more than 4 equipment cycles per hour (or 1 cycle every 15 minutes). Both the Y and W outputs have a 15–minute timer that starts counting down when the output is turned on, (e.g., if Y output is turned on for 9 minutes and then satisfies, it cannot turn back on for another 6 minutes regardless of demand). However, pressing UP and FAN buttons simultaneously or changing the setpoint will override the timer for 1 cycle.
Minimum On Timer
Once the equipment has turned on, it will remain on for a minimum of 3 minutes regardless of demand. However, the equipment can turn off in less than 3 minutes if a change in setpoint or a change in mode occurs.
Staging Timer
If the thermostat is configured for a heat pump application, it has 2–stage heat capability. In normal operation there is a 15–minute delay between the first and second stages of heat. The Y output will energize first, then 15 minutes later, W is allowed to come on if the thermostat determines it is not satisfying the demand. However, if the heating demand is greater than 5_F/3_C, there will be only a 30–second delay before bringing on W.
Auxiliary Heat Indicator
When operating a heat pump and either auxiliary heat or emergency heat is active, the AUX HEAT icon will show on the LCD.
ErrorMessages
If the room temperature sensor fails, two dashes (—-) will appear in the temperature display and all heating and cooling outputs will be turned off. The thermostat must be replaced. If the internal non–volatile memory fails, E4 will alternately flash with the temperature on the display and all heating and cooling outputs will be turned off. The thermostat must be replaced.
Fan Operation
Heating Operation
Cooling Operation
Table 1 shows the thermostat outputs for each available stage of heating or cooling. It may be useful in checkout or troubleshooting.
Table 1 – Outputs
EQUIPMENT CONFIGURATION OPTION #1 | COOL STAGE 1 | HEAT STAGE 1 | HEAT STAGE 2 | EM HEAT |
AC, PC | Y, G | W | — — | — — |
HP, PH RVS = C | Y, G, O/B | Y, G | Y, G, W | W |
HP, PH RVS = H | Y, G | Y, G, O/B | Y, G, W, O/B | W |
Auxiliary Heat
If the system has determined that it’s too cold outside for your heat pump to heat the house without help, the AUX HEAT icon will indicate that the system is getting help from the electric heaters. This happens automatically.
Emergency Heat (EMHT)
If the heat pump is not working properly, you can manually turn on the emergency heat by pressing MODE until EMHT appears. You’ll know there’s a problem if the house can’t seem to get warm when it’s cold outside. You want to avoid using emergency heat continuously, though, because it’s the most expensive option. If you suspect a problem with your heat pump, call your heating and cooling dealer immediately.
In some situations, two AA batteries are the power source for the thermostat. If batteries are used with your equipment, then they should last about one year. As the batteries lose their power, a battery icon appears on the display showing one black bar and then none. As the icon becomes empty, you will begin to lose thermostat functions because the batteries are losing their power. When the batteries are completely dead, you won’t be able to use the thermostat.
When using batteries for power, we recommend you replace them with two AA alkaline batteries. They are in a compartment under the removable faceplate of the thermostat. You do not have to remove the thermostat from the wall to replace the batteries Simply use your thumb and forefinger to grasp and pull the branded faceplate away from the thermostat to expose the batteries. Lift out the batteries, and replace them. Be sure to orient batteries in the direction indicated by the embossed symbols shown on the plastic.
FIVE YEAR WARRANTY
CARRIER CORPORATION (hereinafter “Company”) warrants this product against failure due to defect in materials or workmanship under normal use and maintenance as follows. All warranty periods begin on the date of original installation. If a part fails due to defect during the applicable warranty period Company will provide a new or remanufactured part, at Company’s option, to replace the failed defective part at no charge for the part. Alternatively, and at its option, the Company will allow a credit in the amount of the then factory selling price for a new equivalent part toward the retail purchase price of a new Company product. Except as otherwise stated herein, those are Company’s exclusive obligations under this warranty for a product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed below and on the reverse (if any) of this document.
OWNER–OCCUPIED, RESIDENTIAL APPLICATIONS
This warranty is to the original purchasing owner and is transferable only to the extent and as stated in the Warranty Conditions. The warranty period is five (5) years and is not transferable.
WARRANTY CONDITIONS
THERMOSTAT LIMITED WARRANTY
THIS WARRANTY DOES NOT INCLUDE ANY ADDITIONAL LABOR ALLOWANCE OR OTHER COSTS incurred for diagnosis, repairing, removing, installing, shipping, servicing or handling of either defective parts or replacement parts. SUCH COSTS MAY BE COVERED BY a separate warranty provided by the installer.
LIMITATIONS OF WARRANTIES: ALL IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY) ARE HEREBY LIMITED IN DURATION TO THE PERIOD FOR WHICH THE LIMITED WARRANTY IS GIVEN. THE EXPRESSED WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, SERVICE PROVIDER OR OTHER PERSON WHATSOEVER.
CARRIER WILL NOT BE RESPONSIBLE FOR
39004DP495
Replacement Components, Carrier Corporation
Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.
Replaces: RCIIP710U—21NHP—02
Downloaded from www.Manualslib.com manuals search engine
Totaline P710U-21NHP Non-Programmable Thermostat Installation Instructions
Totaline P710U-21NHP Non-Programmable Thermostat Installation Instructions
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…