Transmitter
Receiver
This is a WiFi controlled device. Use your smart phone to PROGRAMME USING THE App (see the separate App guide), OR PROGRAMME USING THE THERMOSTAT TOUCH CONTROLS (see instructions below)
Whilst in program mode (display shows PRG in the top-right) , you can adjust the set temperature by touching the UP or DOWN arrows. This is a temporary override of the current temperature setting. The display will change from showing ‘ROOM’ and the current measured temperature, to showing ‘SET’ and the temperature that you are now setting. Five seconds after you have changed the temperature to the value you want for the time-being, the thermostat will ‘time-out’ and once again show ‘ROOM’ and the measured temperature. The heating will be switched ON or OFF according to the adjustment you have made. The programmed time / tem-perature setting will be restored with the next program entry in the memory.
Permanent override—manual mode using the SET icon
In the program run mode, touch the SET icon briefly to choose between Program mode (PRG) or manual mode
(sun symbol
Set the time & weekday:
Insert the batteries with correct polarity. The screen will jump to time-setting mode. Or—during normal opera-tion, touch the SET icon for 5 seconds to go into time-setting mode. Using the UP and DOWN arrow icons you can set the current time and weekday. Whether you change a value or not, touch the SET icon to confirm and move on to the next setting. Touch ON/OFF or BACK, or the VIBE will ‘time-out’ to run mode after about ten seconds.
Power
Slow flash when connected by switch connection
Heating on
ON or OFF indicating the output state.
Slow flash if WiFi offline, or RF connection lost Rapid flash when in RF or WiFi configuration mode
Programming: reviewing or changing the factory pre-set program:
The VIBE – model OP-WFSTAT – has a factory pre-set sequence as shown in the table below:
Monday to Friday | ||||
Program | 1 | 2 | 3 | 4 |
Time | 06:00 | 08:00 | 16:00 | 22:00 |
Temp °C | 20 | 15 | 20 | 12 |
Saturday & Sunday | ||||
Program | 1 | 2 | 3 | 4 |
Time | 06:30 | 08:30 | 16:00 | 22:30 |
Temp °C | 21 | 15 | 21 | 12 |
PROG: Touch the PROG icon for 5 seconds – the display will show the first program. You can confirm the time by touching the PROG icon again, or change in 15 minute increments by touching the UP or DOWN arrow icons. Touch the PROG icon to confirm, and then you will be viewing the temperature. Confirm by pressing the PROG icon, or change the value in 0.50C steps to the new required temperature by touching the UP or DOWN arrows. Touch PROG to confirm. You will then be viewing the second time / temperature program. Touch PROG to con-firm, or change with the UP / DOWN arrow, and confirm with the program icon. If you want to create your own program, you must over-write the pre-set sequence. It helps to write down what you require first. A blank table is printed for your use below if required. After programming you can touch the ON/OFF or ‘Back’ icons to save and quit, or 10 seconds after the last button touch the VIBE will time-out to program mode. If whilst program-ming, you change a temperature value during the current program period, you can apply the changed tempera-ture immediately after quitting programming, by touching SET – wait 30 seconds – then touch PROG.
Monday to Friday | ||||
Program | 1 | 2 | 3 | 4 |
Time | ||||
Temp °C | ||||
Saturday & Sunday | ||||
Program | 1 | 2 | 3 | 4 |
Time | ||||
Temp °C |
Using the four available program spaces you can set a temperature profile to suit your personal schedule. An example is shown below. If required, each timed period can be set to a different temperature.
Parameter setting — how to configure the way your Optimum Vibe thermostat works: SET +
Option | Description | Range | Default value |
01 | Temperature calibration | -80C ~ +80C | 00C |
02 | Maximum temperature setting | 50C ~ 350C | 350C |
03 | Minimum temperature setting | 50C ~ 350C | 50C |
> 05 | Frost-protection temperature | OFF; 50C ~ 150C | 50C |
09 | Hysteresis (differential) | 0.50C ~ 3.50C | 0.50C |
17 | Reset (reset all values to default) | Change to 1. Touch Power button for 5 secs | 0 |
18 | Firmware code | Non – adjustable * | 31C4 |
19 | Firmware code | Non – adjustable * | 0110 |
50 | Backlight | 0: OFF 1: AUTO | 1 |
> 52 | Temperature regulation mode
(not applicable if you are using Open Therm connections) | NOr: Normal (ON/OFF)
OPs: Optimum Start
tPi: Time Proportional / Integral | NOr |
> 53 | Time interval for Ops | 10 min, 15 min, 20 min | 20 min |
> 54 | Number of heating cycles per hour (for TPi) | Range: 2 ~ 3 ~ 6 ~ 12 | 6 |
> 55 | Proportional Bandwidth (for TPi) | Range: 1.50C— 30C | 20C |
56 | For future use | ||
57 | For future use | ||
58 | For future use | ||
59 | For future use | ||
60 | For future use | ||
61 | For future use | ||
62 | For future use | ||
63 | For future use |
See additional notes about these configuration options on Page 4
Firmware is pre-loaded in the factory. Firmware versions correct at time of going to press
Configuration options—additional notes:
Option | Description |
05 | If you set a frost-protection temperature, the heating will be switched on when the measured temperature falls below this level, even if the thermostat has been turned off. |
10 | 0 (default) shows Set and Room temperatures. Setting 1 shows Set temperature only. |
52 | Please read ‘how it works’ for a full explanation of temperature regulation modes |
53 | For Optimum Start regulation. For best function, the time interval selected should equal the time taken to increase the room temperature by 1 degree. |
54 | For TPi regulation. Select a low number for fast-acting systems, and a high number for slow-acting systems |
55 | For TPi regulation. Sets the temperature below the set-point at which TPi control will begin |
In normal use, the batteries should last for 12—18 months. ‘Normal use’ allows for one user interaction per day—
frequent use of the backlight will drain the batteries more quickly. When the batteries need to be replaced, the display will alternate between LO bAt and the normal display every 30 seconds. After changing the batteries, your programming and configuration settings are saved, but you will need to input the time and weekday. The screen will jump to time-setting mode. Use the UP or DOWN arrows to adjust the minutes, hours and weekday. Confirm each setting by touching the SET icon. When you have completed setting, touch the ON/OFF or BACK icons to return to normal run mode.
Refresh WiFi or RF link
Receiver ON / OFF
You can disable the heating by turning off the receiver. The receiver’s output will switch off, and it will stop re-sponding to signals from the transmitter.
Transmitter ON / OFF
You can save battery power on the transmitter (thermostat), by touching the ON/OFF icon. The transmitter is powered-down
and will stop sending control signals; the receiver will remain in it’s current state (ON or OFF). If the receiver is powered-up you can control the output by pressing the override button.
868 MHz radio frequency control set, with 4 character hexadecimal coding giving 65,536 code combinations. Transmitter power 2 x AAA alkaline. Touch-screen keys. 70 x 40mm backlit LCD. Dimensions 120 x 85 x 22.5mm Dual RF and WiFi 2.4 GHz receiver: power 230V AC, volt-free changeover 10A (resistive) switching, ON/OFF & manual override buttons. Dimensions 85 x 85 x 25mm. Wall-fixing centres 60mm. Set control features: 20—30m range in buildings. ON/OFF, Optimising & TPI temperature regulation. Hysteresis +/- 0.50C. 5 & 2 or 7 day programming. 5 time / temperature periods. Temperature range 5—35 0C.
Boiler Plus compatible: Class IV control, 2% contribution to system efficiency
Approvals: CE – Radio Equipment Directive EN 2014/53/EU – RoHS
Do not dispose of this product with household waste – use local recycling facilities
D0OWNLOAD MANUALS:
Tfc Tower WFSTAT PROGRAMMABLE THERMOSTAT USER INSTRUCTIONS
OTHER MANUALS:
Tfc Tower WFSTAT PROGRAMMABLE THERMOSTAT PRODUCT DATA SHEET
Tfc Tower WFSTAT PROGRAMMABLE THERMOSTAT Operating Guide
Tfc Tower WFSTAT PROGRAMMABLE THERMOSTAT INSTALLATION INSTRUCTIONS
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…