Tfc Tower WFSTAT PROGRAMMABLE THERMOSTAT Operating Guide

Tfc Tower WFSTAT PROGRAMMABLE THERMOSTAT

WFSTAT OPTIMUM VIBE WiFi PROGRAMMABLE THERMOSTAT

The OPTIMUM VIBE – Model WFSTAT incorporates both radio frequency and WiFi connectivity.

• The control set – when configured for T.P.I. control – meets the UK Government BEIS Department’s criteria for Class IV control, contributing 2% to the energy efficiency of the system.
• The transmitter is battery-powered (2 x AAA alkaline); the receiver is mains-powered, with volt-free switching
• The control set uses the license – free 868 MHz radio band to communicate between transmitter and receiver. The receiver incorporates both 868MHz RF and 2.4GHz WiFi communications. The Optimum
• Connect C-Home App (or the Tuya Smart App) will allow control of the thermostat and receiver wherever you are, from your smart phone via your WiFi router.

Install the C-Home App on your iOS or Android mobile phone – scan the QR code for your device below, or search C-Home on the iOS App or Google Play StoreThe Tuya Smart App can also be used to control your Optimum Connect devices.

Load the App and follow the instructions to create your user account

Before adding the thermostat in the App, make sure that you first connect the receiver and power-up the receiver. Then add the device as noted below.
Once the App is installed on your smart phone you can add the VIBE – WFSTAT. If you have a dual-band WiFi router, make sure that your phone is connected to the 2.4GHz network. You may have to separate the 2.4 GHz and 5 GHz networks in the home page of your router to do so, as smart phones will often connect to the 5GHz network by default.

• In the App home screen touch the + icon (top RH corner) to add a device.
• Select ‘Small Home Appliances’ in the left-hand column
• Select ‘Thermostat’ from the list of devices; you may have to scroll down to find the Thermostat icon—see the partial screenshot here
• Re-enter your router password (if prompted) .
• Press and hold the receiver manual button until the Red Heating on LED flashes rapidly . Release the button (the LED should continue flashing rapidly)
• On the App, press ‘Confirm’ – the App will load the device. The LED will stop flashing. The WFSTAT will display in the App Home Screen with the icon as shown here.

Notes on LED function:
The Red ‘Heating on’ LED is ON or OFF indicating the output state. It flashes quickly when in Wifi or RF configuration mode. It flashes slowly if WiFi is offline or RF communication has failed.
The Green ‘Power’ LED is ON and flashes once per second – when connected.

• Follow the instructions below to control the VIBE – WFSTAT with your smart phone.
• The home screen gives access to other functions:
• Switch – switch the transmitter (thermostat) ON or OFF.
• Note that if you turn the thermostat OFF, whilst this will save battery power, the thermostat will no longer control the heating, which will also remain OFF.
• Setpoint – touch the slider or ˄ / ˅ to change the current temperature set-point
• Mode – Allows you to quickly change from Auto (programmed) temperature, to Manual or ECO temperature levels. Manual and ECO temperature levels can be set from the Setpoint screen

Touch the Heating Thermostat panel icon , to open access to additional functions.

Weekly program screen: adjust day / time / temperature programming

QR058 Prepared for TFC Group by: J. Todd Issue 2: August 2020

REFERENCE:

DOWNLOAD MANUALS:

Tfc Tower WFSTAT PROGRAMMABLE THERMOSTAT Operating Guide

OTHER MANUALS:

Tfc Tower WFSTAT PROGRAMMABLE THERMOSTAT USER INSTRUCTIONS

Tfc Tower WFSTAT PROGRAMMABLE THERMOSTAT PRODUCT DATA SHEET

Tfc Tower WFSTAT PROGRAMMABLE THERMOSTAT INSTALLATION INSTRUCTIONS

Tfc Tower WFSTAT PROGRAMMABLE THERMOSTAT Operating Guide