Tado

tado° Wireless Temperature Sensor thermostat Installational Manual

tado° Wireless Temperature Sensor thermostat

For the Starter Kit – Wireless Smart Thermostat V3+ English International

This manual is meant exclusively for professional installers. It includes generic instructions to install the Wireless Receiver and the Wireless Temperature Sensor. Manual version 3.2

DIY Installation

If you are not a professional installer, please download the tado˚ app. There you will find specific installation instructions.

Install the Internet-Bridge

  • Connect the Internet Bridge to the router.
  • If no free USB port is available on the router, use the included 5V power adapter
  • Press and hold the pairing button until the pairing LED starts blinking.

Pair the Wireless Temp. Sensor

If pairing fails (E0), make sure the distance between the devices is approximately 3 meters. Pair again by pressing the button for 3 sec.

Mount tado˚ devices

  • Mount the Wireless Temperature Sensor to the wall using the included screws or the adhesive pads.
  • Mount the Wireless Receiver to the wall using the included screws.

Extra information: Wireless Receiver Symbols

Unfold to check:
Step 4: Wire the Wireless Receiver Step 5: Pair the Wireless Receiver Step 6: Configuration

wire the Wireless Receiver

Caution!
Turn OFF the power before wiring! Always use the included strain reliefs and position them on the outer insulation layer of the cable.

Check the boiler manual before wiring
Identify the control interface and check if it is supported by trade ̊.

The factory default configuration is Relay. If the Wireless Receiver is wired via Relay, step 6 (configuration) can be skipped.

Potential Free Relay

230V Relay

Digital

VR33 OpenTherm translation module (in the Netherlands) should be removed. Only compatible with one heating circuit. Any existing fit-in controller should be removed. ***Special configuration is needed on the boiler for the KM-Bus interface, see table on back page

Analog

Pair the Wireless Receiver

  • Put the cover on the device. Tight the housing screw to secure it.
  • Plug in the power supply cable and turn the power back ON.
  • Wait 30 sec, then press the button for 3 sec to start pairing.
  • Solid on indicates successful pairing

Configuration

Use the Wireless Temperature Sensor to configure the Wireless Receiver interface according to the tables above (Hot Water control & Config. Menu ID).

Boiler Configuration ONLY for Viessmann KM-Bus

 Test the system

Need help?

Get expert advice on our tado° installer hotline: +44 20 3893 2159

REFERENCE:

DOWNLOAD MANUALS:

tado° Wireless Temperature Sensor thermostat Installational Manual

tado° Wireless Temperature Sensor thermostat Installational Manual

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago