Smarttemp

Smarttemp SMT-775 TOUCH-SCREEN THERMOSTAT Quick Start Guide

Smarttemp SMT-775 TOUCH-SCREEN THERMOSTAT

Introduction

Thank you for your purchase of the Inspire Touch air conditioning control system. This premium product has been designing and engineered by Smart Temp Australia to provide you with simple and accurate comfort control over multiple temperature-controlled zones.
This quick start guide provides basic information that may be helpful to provide initial guidance on how to get the best from your new Inspire Touch air conditioning control system.
The full manual for the Inspire Touch can be downloaded at www.smarttemp.com.au. Simply type “Inspire” into the search bar at the top of the page or scan the QR code to the right.

Turning Your Heating or Cooling On or Off

Simply tap the Mode icon to open the Mode window. You will be presented with the option to select your desired available heating and cooling mode (or switch the system off). You also may select fan speed. This setting will apply to all zones in the system.
If available, using “Auto” (equipment) Mode and “Auto” Fan Speed is recommended.

Zone control

If zoning is enabled on your system, the Zone icon will open the Zone page where you are able to manage the individual zones under the control of the Inspire Touch. Depending on how your zones have been installed, you will be permitted to open or close a zone and possibly adjust the zone temperature or schedule.

Wi-Fi Control

Your Inspire Touch can be controlled by a free mobile App from anywhere in the world where you have internet access. Setting up Wi-Fi is a relatively easy process.

  1. On the Inspire Touch screen click the Settings icon and then click the Wi-Fi tab.
  2. Scan for your home / office Wi-Fi network and join. You will need to enter your Wi-Fi password.
  3. Tap the name of the network you have just joined and a page showing your Network information will be shown. If you see four astricts at the bottom of this page, tap the astricts to reveal a hidden pair key. You may be prompted by a PIN request. If so, the factory default PIN is 1234.
  4. Download and install the Smart Temp Inspire Touch App onto your smart device and sign up to a new account.
  5. On your App click the top right corner and select “Add Device” and then“Smart Capture”. Your phone camera will be activated.
  6. Using your Smart phone camera (within the Smart Temp Inspire Touch App) take a picture of your Wi-Fi settings page making sure you capture both the MAC address (top line) and Pair Key (bottom line).

The Smart Temp Inspire Touch App will analyse this picture and join the Inspire Touch to the account that took the picture. Pairing is now complete.

Entering the Installer Menu

The Inspire Touch has a comprehensive installer menu that will permit you to set up equipment staging, zone logic and numerous other settings. It is strongly recommended that you do not alter settings in this menu if you are unfamiliar with the effect of changing these settings.
To enter the Installer menu, tap the Installer icon and enter the default pin of 1234. Thermostat one will be selected by default so just tap Continue on the lower right. Move forward or backward through the pages using the arrows on the bottom and tap the tabs across the top of the page to enter the menu. Tap to highlight Yellow the function you wish to change and use the Up and Down buttons to make adjustments. There are multiple pages of menus with clearly labelled functions on each page.
Tap exit (top right) to exit the Installer menu and save changes. The Inspire Touch will re-boot and apply the changes.
Typical wiring diagrams are provided below. More information on wiring is provided in the online manual.

DIP Switch Settings
There are three dip switches that must be set to define how the Inspire Touch controls the HVAC system. These switches are read by the Inspire Touch on power up so if changing these switches, you must power cycle the Inspire Touch control card before they are taken into effect. The installer menu, where relevant, will confirm these switch settings.

Switch Off On
Sw1 – Fan Speeds Sw1 – Single Speed Fan Sw1 – 3 Speed Fan
Sw2 – System Sw2 – Heat Cool Mode Sw2 – Heat Pump Mode
Sw3 – Reversing Valve (If Sw2 = ON) Sw3 – Energise in Cool (O) Sw3 – Energise in Heat (B)
Sw3 – Fan with Heat (If Sw2 = OFF) Sw3 – Fan Controlled by Heater (HG) Sw3 – Fan Controlled by Inspire (HE)

REFERENCE:

DOWNLOAD MANUALS:

Smarttemp SMT-775 TOUCH-SCREEN THERMOSTAT Quick Start Guide

OTHER MANUALS:

Smarttemp SMT-775 TOUCH-SCREEN THERMOSTAT Installer Manual

Smarttemp SMT-775 TOUCH-SCREEN THERMOSTAT PRODUCT SPECIFICATION GUIDE

Smarttemp SMT-775 TOUCH-SCREEN THERMOSTAT Quick Start Guide

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

2 years ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

2 years ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

2 years ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

2 years ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

2 years ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

2 years ago