SIEMENS

SIEMENS REV34-XA Room thermostat Operating Instruction

SIEMENS REV34-XA Room thermostat

Operating instructions

REV34.. – 7-day room temperature controller for the right temperature at the right time. All factory settings already provide optimal living comfort. You can easily adjust the controller to your needs with the user-assisted clear-text display and program selection slider.

Note the following for placing the controller: 
Make sure no other influencing factors influence the controller’s temperature sensor (no solar radiation and other heat or cold source influences).

Display

Operating elements and settings

Special symbols displayed
The controller display can show the following special symbols:

Is symbol displayed ? 
The alarm indicates an error!
Press the Info button and check the error message (e.g. radio clock signal, radio connection to receiver, etc.). Contact a specialist as needed.

Is symboldisplayed ? 
This symbol tells you that you must exchange the batteries within the next 3 months.
Insert 2 new alkaline batteries type AA, 1.5 V as follows:
Remove the controller from the mounting base; open the battery compartment on the rear; remove the old batteries; insert the new batteries and reinsert the controller in the base.

Caution: Time and date are retained for max. 1 minute. (All other settings are fixed and remain unchanged!)
Dispose of the batteries as per regulations.

Is symbol displayed ?
The radio clock symbol only appears if the receiver is set up and activated to receive the time signal from Frankfurt (Germany). A permanent symbol indicates that both time and date of the controller are synchronized to Frankfurt (DCF77).
The symbol flashes if the signal is not received for more than 1 week.

Is symboldisplayed ? 
The controller is in heating mode .

Commission the controller and quick start

The controller contains a factory-set heating switching pattern and temperature values. Proceed as follows for initial commissioning:

Fold the operating instructions and reinsert in the mounting base.
Turn on display lighting, check error messages or other important information

Change the temperature level in the time switch program, or are you not at home for a while?

Tips to save energy without reducing comfort 

  • Heat your rooms to max 21 °C.
  • Useto switch to energy saving temperature even if you are absent only briefly.
  • Air out your rooms briefly, but with wide-open windows.

Select operating mode 
Press the operating mode button to select one of 5 modes.

Operating modes with time program

The controller offers both time programs Automatic and Exception day .

Note: To set your own programs, see: “Enter customized temperatures and switching times”.

Continuous operating modes

The controller offers continuous operating modes “Continuous comfort mode
“Continuous energy saving mode“ and frost protection mode .

Enter time and date

Enter customized temperatures and switching times
The controller has three different switching patterns that you can allocate to the weekday blocks 1-5, the weekend block 6-7, or to the individual days 1…7.

Proceed as follows:

Enter holidays or absence

You can enter start, temperature and end of your holidays. The controller switches to the set holiday temperature at the start of the holidays and back to the preset operating mode at the end of the holidays.

During holiday mode, symbolflashes and the end of the holidays is displayed.

Proceed as follows:

Enter temperature for active remote control
With remote control, you are free to select the temperature. Activating remote control immediately enables control to the remote operating temperature regardless of the current operating mode. After you switch off remote control, the device returns to the set operating mode.

Symbol flashes with active remote control.

Proceed as follows:

Reset to factory settings

Activate Party mode

You can activate Party mode only in operating modes. In Party mode, the device controls to any selectable temperature for any selectable time.

In Party mode, symbol is displayed along with the end of Party mode.

Proceed as follows:

REFERENCE:

DOWNLOAD MANUALS:

SIEMENS REV34-XA Room thermostat Operating Instruction

OTHER MANUALS:

SIEMENS REV34-XA Room Thermostat Product Specifications Guide

SIEMENS REV34-XA Room thermostat Operating Instruction

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago