SIEMENS RDE100.1 RFS Programmable Room Thermostat Operating Instruction

SIEMENS RDE100.1 RFS Programmable Room Thermostat

Operating Instructions

RDE100.1DHW is a room thermostat that allows you to set the ideal room temperature at the time you want.
In addition, it offers independent control of DHW. There are several switching patterns available that can be set to your specific needs.

1. Display
   • Indicating that batteries need to be replaced
   • Frost protection (heating) is active
   • Auto Timer mode View and set Auto Time switch
   • Comfort mode
   • Economy mode
   • Escape
   • Display of time
   • Permanent setpoint setting
   • Day and time setting
   • Holiday mode setting View and set DHW
   • Auto Time switch DHW Auto Time switch activated
   • Morning: 12-hour format
   • Afternoon: 12-hour format
   • Confirmation
   • Room temperature in degrees Fahrenheit
   • Room temperature in degrees Celsius
   • Button lock activated
   • Display of room temperature, setpoint, etc.
   • Heating ON
   • Weekday 1 = Monday 7 = Sunday
   • Timer bar
   • The actual room temperature
2. Change operating mode
3. Set
4. Ok
5. Decrease value
6. Increase value
7. Battery holder
8. Indication of data transmission and operating state (LED)
9. Initialization of wireless communication with transmitter (LEARN button)

Do you want to set the time of day and the weekday?

You can set the current time of day.

set ok + – mode

Proceed as follows: ·        Press set and select ·        Press ok and the time flashes for setting ·        Press + or – to adjust the time ·        Press ok to confirm ·        The weekday flashes, press + or – to select the desired day ·        Press ok to save the value ·        Press mode to exit or wait for the program to exit automatically

Are your rooms too warm/too cold?

+ – ok set mode

Press + or – to increase or decrease the room temperature setpoint in increments of 0.5 °C / 1 °F. Proceed as follows: ·        Press + or – to adjust the setpoint temporarily. This adjustment is reset as soon as the operating mode changes. ·        Press ok, set or mode to save the value or wait for the program to exit automatically ·        To lock the setpoints, use parameters P06 and P08.

Do you want to change the operating mode?

mode                                 !

The thermostat provides Comfort mode, Economy mode, and Auto mode. Changeover between the operating modes can be made manually by pressing mode. Comfort mode is the permanent (24 h) selection of Comfort. Select this mode to maintain Comfort temperature permanently without any time switch. It is used during occupancy periods, for example. Economy mode is the permanent (24 h) selection of Economy. Select this mode to maintain the Economy temperature permanently without any time switch. It is used during non-occupancy periods, for example at night. AUTO In Auto timer mode, operating modes (Comfort, Economy) are changed automatically according to the time switch set.   Note: Frost protection is a function always active in the background. As soon the room temperature falls below 5 ºC, the unit automatically activates the heating  .

Do you want to set permanent temperature setpoints?

set ok + – mode       !

·        Press set and select ·        Press ok to confirm ·        Press mode to select an operating mode, Comfort or Economy ·        Press + or – to adjust the setpoint permanently. ·        Press ok to confirm ·        Press mode to exit or wait for the program to exit automatically Note: This permanent setpoint is used during Auto timer mode.

Energy-saving tips without loss of comfort

• Select Auto timer mode during the heating period, and set the time switch according to your normal habits at home
• Select Economy mode or Holiday mode for long periods of non-occupancy and during summer period.

Do you want to set your Holiday mode?

set ok + – mode             !

Use the Holiday mode to set the thermostat to a constant temperature while absent. ·        Press set and select ·        Press ok to confirm ·        Press + or – to adjust the temperature setpoint ·        Press ok to confirm ·        Press + or – to adjust the number of days for holidays (Note: 0 = Holiday mode OFF) ·        Press ok to save the value ·        When Holiday mode is activated, the remaining days are displayed on the screen Note: If you press mode while Holiday mode is active, the function is turned off and the  symbol disappears. If the Comfort and Economy setpoint values are both locked, the lowest locked setpoint value is the Holiday mode setpoint value. You can adjust the setpoint temperature from 5 ºC up to the lowest locked setpoint value.

Do you want to enter your own time switch?

Option 1: Time switch with individual day selection (P11=0)

set
ok
+
–
mode
You can select Comfort or Economy at 15-minute intervals throughout the day. The 0:00 to 24:00 hour time bar allows you to set the operating mode for the selected day(s).
Example:

1. Visible bars: Control to Comfort temperature
2. Invisible bars: Control to Economy temperature

When Auto timer mode is enabled, changeover between the operating modes is automatic after the settings are saved.
Proceed as follows:

1. Press set and select AUTO.
2. Press ok to confirm.
3. Time switch for day Mon(1) is displayed.
4. Press + or – to select the day, from Mon(1) to Sun(7).
5. Press ok to confirm the selection and initiate time programming.
   During programming step:
6. Press mode to select an operating mode, (Comfort or Economy) or
7. Press + or – to adjust the time setpoint by 15 minutes for the selected mode.
8. Press ok to save the time switch.
9. Repeat steps 4-8 for all remaining days (if required);
   or
10. Press mode or wait for the program to exit automatically.

Option 2: Time switch with the same 7 day selection (P11=1)

set ok + – mode

You can set all the 7 day time switches at the same time. Example:  Visible bars: Control to Comfort temperature ‚ Invisible bars: Control to Economy temperature  Proceed as follows: 1) Set the parameter (P11=1). Please refer to the section “Do you want to change parameters“. 2) Press set and select AUTO. 3) Press ok to confirm. 4) Time switch for period Mon (1) – Sun (7) is displayed. 5) Press ok to initiate time programming.  During programming step: 6) Press mode to select an operating mode, (Comfort or Economy) or 7) Press + or – to adjust time setpoint by 15 minutes for the selected mode.  8) Press ok to save the time switch. 9) Press mode or wait for the program to exit automatically.

Option 3: Time switch with 5-2 day selection (P11=2)

set ok + – mode

You can set Monday – Friday time switch at once and Saturday – Sunday time switch at once. Example:  Visible bars: Control to Comfort temperature ‚ Invisible bars: Control to Economy temperature   Proceed as follows: 1) Set the parameter (P11=2). Please refer to the section “Do you want to change parameters“. 2)  Press set and select AUTO. 3)  Press ok to confirm. 4)  Time switch for period Mon(1) – Fri(5) is displayed. 5)  Press + or – to select the period, Mon (1) – Fri( 5) or Sat (6) – Sun (7). 6) Press ok to confirm the selected period and initiate time programming. During programming step: 7) Press mode to select an operating mode, (Comfort or Economy) or 8) Press + or – to adjust the time setpoint by 15 minutes for the selected mode. 9)  Press ok to save the time switch. 10) Repeat the steps 5-9 for the other period if necessary; or 11) Press mode or wait for the program to exit automatically.

Factory default for 7-day Time switch

Default value	Day/s	Comfort mode	Economy mode
	Mo (1) – Fr (5)	6:00 – 8:00 hr 17:00 – 22:00 hr	22:00 – 6:00 hr 8:00 – 17:00 hr
	Sa (6) – Su (7)	7:00 – 22:00 hr	22:00 – 7:00 hr

Do you want to pair transmitter and receiver?

+ – Learn		The RDE100.1RF communicates with the RCR100RF at a frequency of 433 MHz. To pair transmitter and receiver, proceed as follows:
Mode		RCR100RF receiver setting:
		1) Press and hold the LEARN button on the
		RCR100RF for at least 3 seconds and
		then release it.
		2) Red and green LEDs flash alternately to
		indicate receiver is in learning mode.
		RDE100.1/RF transmitter setting:
		3) On the transmitter, set the parameters
		(refer to section “Do you want to change
		parameters?”).
		4) Check to ensure that parameter P19 is not
		0, because this would mean that the
		wireless function is disabled. By default,
		parameter P19 is 1.
		5) Proceed to parameter P20. Press Mode
		and parameter P20=0 (OFF) flashes.
		Adjust the value by pressing + to change
		to P20=1 (ON), then press Mode to
		confirm.
		6) During the stages of wireless learning, the
		LCD displays “rF” and “Lrn”. Wait for time
		out, and the transmitter exits the
		parameter setting mode.
		Successful wireless learning:
		7) The green LED on the RCR100RF flashes
		for 10 minutes to indicate that the receiver
		has successfully completed wireless
		learning.
		Recommendation:
		8) Additional test to ensure the wireless
		signal is fine:
		On the RDE100.1/RF, change the
		operating mode by pressing Mode or
		change the setpoint by pressing + or –.
		On the RCR100RF, the green LED should
		flash for 3 seconds before changing to
		constantly green. At the same time,
		observe your radiator, boiler or heater
		indication (if it has one) to ensure that it
		changed the operating mode.
		9) If step 7 or 8 is working fine, this means
		you have successfully paired the units.
		Unsuccessful wireless learning:
		10) If the RCR100RF fails to receive wireless
		data, the red LED starts to flash **.
		Repeat steps 1 to 8 until pairing is
		successful.
	!	Note: Always start receiver learning before starting
		pairing with the transmitter.
		The units must be placed such that transmitter
		and received signals have limited external
		wireless interference.
		**In normal operation, if a drop in wireless
		communication occurs due to unforeseeable
		noise, just leave the receiver and it will recover
		automatically.
		The pairs are saved even if there is a power
		shut down. Communication restarts
		automatically after several minutes without any
		user action.

Does symbol appear on the display?

Symbolis displayed when the batteries are low. Replace them with 2 new alkaline batteries type AAA. Proceed as follows:

• Get 2 new alkaline batteries type AAA
• Remove the battery holder, then the batteries, insert the new batteries and, within 1.5 minutes, replace the battery holder
• Ensure the exhausted batteries are disposed of correctly, in compliance with environmental requirements

Do you want to activate DHW control?

• Press to switch on DHW heating
• While DHW heating is switched on, thesymbol is displayed
• Pressagain
• DHW is in the auto status, the AUTO symbol is displayed. DHW switches according to the DHW time switch.
  If you want to see the DHW time bar, press and holdfor 5 seconds. The time bar flashes to show the programmed DHW times. The timeout of the DHW timer bar is set with parameter P13
• Press again
• DHW heating is switched off and the symbol disappears
  DHW can also be switched on/off while frost protection is active.

Do you want to lock the buttons?

mode	Press and hold mode for at least 7 seconds to activate a button lock. Repeat to unlock. The unit operates normally when the buttons are locked, but no changes are possible while the buttons are locked.

Receiver’s LED indication

State of receiver	State of LED
Power up (or reset)	The red and green LEDs flash alternately for 5 seconds, then change to constantly red. Note: If the receiver was previ- ously programmed, it shows immediately constantly red.
Learning mode	The red and green LEDs flash
	alternatively.
Successful learning	If RCR100RF learning is
mode	successful, the green LED will
	flash for 10 minutes.
Signal ok and output status change	The green LED is constantly lit, and if the output status changes, the green LED flashes for 3 seconds, then changes back to constantly green.
Fail to receive wireless data	If the RCR100RF fails to receive wireless data, the red LED will start to flash after 125 minutes. If the RCR100RF signal is recovered, it will return to the previous LED state.

Do you want to change the parameters?

+ – ok mode

If you want to change control parameters, proceed as follows: ·        Press + and – simultaneously for 5 seconds ·        Release them and parameter “P01” is displayed on the bottom segment ·        Press + or – to scroll to the parameter that needs to be adjusted ·        Press ok to select this parameter ·        Press + or – to adjust the value ·        Press ok to confirm the adjusted value ·        Press mode to exit the parameters without saving or wait for the program to exit automatically

Parameter list

Parameter no.	Description	Setting range (default)
P01	Time format	1 = 24:00 hours (default) 2 = 12:00 AM/PM
P02	Selection of °C or °F	1 = °C (default) 2 = °F
P03	Standard temperature display	1 = room temperature (default) 2 = setpoint
P04	Temperature sensor calibration	-3…3 °C Step 0.5 °C (-6…6 °F, step 1 °F) Default: 0 °C
P06	Comfort setpoint lock	0 = OFF (default) 1 = ON à locked according to setting in permanent temperature setpoint
P08	Economy setpoint lock	0 = OFF (default) 1 = ON à locked according to setting in permanent temperature setpoint
P09	Buzzer	0 = OFF 1 = ON (default)
P10	Show frost protection icon	0 = OFF (default) 1 = ON
P11	Time switch type for autotimer and DHW	0 = individual Days (default) 1= all 7 days 2= 5/2 days
P12	Periodic pump run	0 = OFF (default) 1 = ON
P13	DHW timer bar timeout	0 = no DHW bar 1 = 1 minute (default) 2 = 2 minutes Adjustable range 0 to 15 minutes
P21	Button scanning rate for the capacitive buttons Note: a higher scanning rate means shorter battery life.	0.2 = 0.25 s 0.5 = 0.5 s 1.0 = 1.0 s (default) 1.5 = 1.5 s
P22	Reload factory settings	0 = OFF (default) 1 = reload
P23	Software version information	No adjustment possible
P78	Control behavior	0 = On/Off, 1.0K 1 = On/Off, 0.3K 2 = TPI fast 3 = TPI medium 4 = TPI slow (default)
P89	Forward shift on max	0, 0.5,…24 h Default: 0 h
P90	Early shutdown max	0, 0.5,…6 h Default: 0 h

REFERENCE :

Download Manual:

SIEMENS RDE100.1 RFS Programmable Room Thermostat Operating Instruction

SIEMENS RDE100.1 RFS Programmable Room Thermostat Operating Instruction