Gather this information before you begin the installation for a smoother walk-through.
The Sensi Touch Smart Thermostat is a Wi-Fi-enabled device. To install and configure your thermostat correctly, you must use the Sensi app. To start the installation process, download the Sensi app to your smart phone or tablet. It is a free download. The Sensi app requires the following Operating System (OS) software to download:
When you download the Sensi app, you will be prompted to create an account. This is required to access your thermostat remotely and use all the features Sensi offers. Use a valid email address and a password of your choosing to create an account. Remember this email address and password. Your Sensi thermostat will be linked to this email address once it is registered.
Once you have downloaded the Sensi app, and have created an account, you are ready to install the thermostat to your wall and connect it to Wi-Fi. If no thermostats are registered yet, tap the plus (+) sign to add a thermostat. First, choose which thermostat you purchased. The Sensi Touch The smart Thermostat option is for the following model numbers:
• 1F95U-42WF series
• ST75 series
• NH-AWIFI, OH-WIFI
No, it needs to be installed.
This option will walk you through the entire installation process, including identifying and connecting your wiring, as well as connecting to Wi-Fi. The Sensi app will walk through a step-by-step process for installation.
Gather Tools and Package Contents
Gather all the necessary tools for installation.
Turn Off Power
Turn off the power to your heating and air conditioning system before handling your thermostat wires.
Remove Old Thermostat Cover
Remove the cover using a screwdriver or by pushing the pressure latch. Some covers pull off while others need to be released using a screwdriver.
Photograph Your Wiring
THIS IS IMPORTANT. The Sensi app will prompt you to take a picture of your existing thermostat and old wiring in case you need it later. This can be helpful for troubleshooting with our technical support team if necessary. The picture you take will be saved to your camera roll or photo gallery.
Throw Away Any Jumper Wires
Sensi has a jumper wire built into it, and you will not need any jumper wires from your old unit.
Choose Wire Terminals
System Type
Select what type of system you have.
Label Your Wires
Using the provided wire label stickers, label your wires by removing one wire at a time.
Disconnect Wires and Remove Base
After all of your wires are labeled, remove the old thermostat base from the wall.
Install Sensi Base
Use the provided mounting screws and secure the Sensi base to the wall.
Connect the Wires
Once the Sensi base is mounted and secured on the wall, insert the wires into the terminals. Simply push the wires into the terminal slots. Use a screwdriver to secure each wire in place
Attach Cover
Push the front display onto the thermostat base. If you used the “Backlight” feature, please make sure the switch is turned “Off” so you can control it from the display.
Turn On Power
Turn the power to your system back on.
This portion of the installation guide covers how to connect your thermostat to Wi-Fi. If you chose the first option, “No, it needs to be installed,” the app will provide instructions for installing and wiring your thermostat before you connect to Wi-Fi. If you had your Sensi thermostat installed by a professional or if you have already installed and wired your Sensi thermostat yourself, but have not yet connected to WiFi, choose “Yes, it is on the wall.” The app will jump right into connecting your thermostat to Wi-Fi.
BROADCAST SENSI NETWORK
On the thermostat, press Menu, and then Wi-Fi. Depending the Sensi version you may see “Set up new network” or you may see two icons. If you see two icons, you’ll have the option to bypass HomeKit setup.
CONNECT YOUR SENSI THERMOSTAT TO YOUR WI-FI NETWORK WITH THE SENSI APP
Follow the step-by-step instructions in the Sensi app. The Wi-Fi connection process will be slightly different based on your device’s operating system (iOS/Android), Sensi app version, and the version of Sensi thermostat that you have.
Name Thermostat
You can select a name or choose a custom name for your thermostat. Press “Next” to continue.
Register thermostat
After successfully connecting Sensi, the app will prompt you to register the thermostat. You can either choose the “Locate Me” option or fill in your street address, city, state, zip code, country and time zone manually. Press “Next” to continue.
Contractor Information
If a contractor professionally installed your thermostat, and registered as a Sensi partner, they have the option to input their phone number here. If there is not a registered number available, simply hit “Next” to continue.
Start Using Sensi
Congratulations on successfully installing Sensi. Press “Start Using Sensi” to open the main screen of the app.
Connecting to Wi-Fi Troubleshooting
If you’re having trouble connecting to Wi-Fi, here are some tips to try:
If you replaced your router or changed your Wi-Fi network password, you will need to reconnect your thermostat to Wi-Fi. This is different depending on what smart device you are using. Please see our support article for more information on how to reconnect.sensi.emerson.com/en-us/support/ reconnecting-sensi-thermostat-to-wifi
Blank or flashing display
If you installed a Sensi Touch Smart Thermostat, but the touchscreen is still blank or only flashes after completing all the steps in the Sensi app, then most likely the thermostat is not receiving enough power from your system to turn on or stay on continuously. Sensi Touch requires a “C” wire to power the thermostat. Sensi does have a battery-powered light in the sub-base for installation, but that light will only last for about an hour, and is not an indicator that there is the power to the thermostat.
I DON’T HAVE A WIRE IN THE “C” TERMINAL.
Sensi requires a “C” wire. If you don’t have a wire in the “C” terminal, check out our “C” wire videos for DIY installation at sensi.emerson.com/en-us/c-wire. If you are installing Sensi to a heat-only system, you may be able to install an external transformer. Learn more about that option by searching “external transformer” on our support site at sensi.emerson.com/en-us/support.
I HAVE A WIRE IN THE “C” TERMINAL.
HVAC configuration menu
If you chose the option “No, it needs to be installed” and walked through the installation process on the Sensi app, the app should have correctly configured your thermostat for your system type. However, if you are experiencing an issue or you want to check your system configurations, you can manually configure your thermostat as well. Learn more about how to properly configure your thermostat by searching “configure” on our support site at sensi.emerson.com/en-us/support.
CONFIGURATION MENU ITEMS REFERENCE | ||
Menu item | Description | Options |
Outdoor Equipment | Select AC or Heat Pump equipment, as well as the number of stages. Set this to AC1 for single-stage systems or HP1 or HP2 for single or multi-stage heat pumps | AC1/AC2/HP1/ HP2/None |
Indoor Equipment | Select whether the equipment is an electric or gas furnace, or fan only. Set this to EL1 for single-stage electric or GA1 or GA2 for single or multi-stage gas systems. | GA1/GA2/EL1/EL2/Fan |
Reversing Valve Position | When configured for O, reversing valve is energized in Cooling. This will cover most applications. Some manufacturers such as Rheem or Rhudd use the B terminal, which would energize in heating. For three-wire zone hydronic systems set this to Z. | O/B/6/None |
Additional Accessories | ||
Humidifier (wired to thermostat) | If a humidifier is wired to the thermostat, change the Humidifier setting to YES | Yes/No |
Dehumidifier (wired to thermostat) | If a dehumidifier is wired to the thermostat, change the Dehumidifier setting to YES. | Yes/No |
Accessing your Sensi thermostat from other devices
When you log into your Sensi account with your email address and password, the app will be able to control all the thermostats registered to your Sensi account. If you give someone else your email address and password to your Sensi account, they will be able to log in and control any thermostats registered to that account. You can change your email address and password from inside the app. Be aware of this when giving out your information. There is no limit to the number of devices that can access the thermostat.
Forgot password
If you forgot the password to your Sensi account, click on “Forgot Password” on the login screen of the Sensi app. A temporary password will be sent to the email address that you use to login.
Installing multiple thermostats
If you are installing more than one thermostat, follow the same installation process in the Sensi app. Once you have one thermostat installed, open the Sensi app on your phone. At the main screen, press the + sign to add another thermostat to your account.
Accessing account information
You can use the Account area to access your email preferences, change your account information and email address associated with your Sensi.
For iOS: Tap the person icon in the upper right hand corner.
For Android: Tap the three dots in the upper right hand corner.
For problems connecting your Sensi thermostat, call or email the Sensi Technical Support team, and they will be happy to help you or your contractor walk through any steps needed to troubleshoot the Sensi thermostat.
SINGLE-STAGE OR MULTI-STAGE SYSTEM NO HEAT PUMP WITH TWO TRANSFORMERS
HEAT PUMP SYSTEMS
Download manual:
SENSI st75 TOUCH SMART THERMOSTAT Installation guide
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…