Saswell SAS922WHL-7W-S-WIFI WifiProgrammable Thermostat User Manual

Saswell SAS922WHL-7W-S-WIFI WifiProgrammable Thermostat

INTRODUCTION

Wireless Thermostat SAS922WHL-7W-S-WIFI
Thermostat Saswell SAS922WHL-7W-S-WIFI is a wired thermostat for managing of heating systems. What’s special about this thermostat is that it is controlled via application through your smart phone. All temperature settings and the regulation itself is easily controlled via the app or in some cases via the thermostat. The system also allows programming of the Heating schedule for 7 days (each separate) with 6 switches per day. The instructions for use and maintenance are part of the general terms and conditions of sale. We reserve the right to change the details, technology and performance. The guarantee is valid only with the original invoice. We allow the possibility of errors in the text

Environmental Protection
Do not place electronic devices and batteries after the end of their life in mixed municipal waste, use collection points of separate waste. By properly removing the product, you will prevent negative effects on human health and the environment. Recycling of materials contributes to the protection of natural resources. More information on the recycling of this product is offered to you by administrative units, household waste treatment organizations or the point of sale where you purchased the product

Important notes before first use, installation and maintenance

• Before use, carefully read the manual not only for the thermostat, but also for the Heating device (heat pump, pumps, boilers, etc.)
• Turn off the power supply before installing the thermostat!
• We recommend that the installation is done by a qualified electrician
• the electrical circuit must be secured with a fuse that does not exceed the current load of wiring
• Please note all safety instructions before installing
• Do not expose the product to direct sunlight, extreme cold, humidity and sudden temperature changes. This would reduce the accuracy of the temperature measurement
• Do not place the product in places that are prone to vibrations and shocks – this can cause damage
• Do not expose the product to excessive pressure, shock, dust, high temperatures or moisture, as these can cause damage to one of the product of the functions, shorter energy endurance, damage to batteries, and deformation of plastic parts.
• Do not expose the product to rain or moisture, dripping or spraying water.
• Do not place any sources of fire on the product, for example, spark plugs etc.
• Do not place the product in places where there is insufficient air circulation.
• Do not insert any objects into the ventilation openings.
• Do not interfere with the internal electrical wiring of the product. It may be damaged and therefore terminate the warranty. The product must only be repaired by a trained specialist.
• Use a moderately moistened cloth for cleaning. Do not use solutions or cleaning products – may damage plastic parts and electrical wiring
• Do not immerse the product in water or other liquids.
• Do not repair it yourself if the product is damaged or defective. Put it in the repair shop where you bought it
• The product should not be used by a person (including children) by physical, sensory or mental disability or lack of experience and knowledge impeded by the safe use of the device if they are not controlled, or if they were not informed by the person responsible for their safety about the use of the device
• Children’s control is necessary to ensure that they do not play with the device

Features

• Portability of room thermostat and independence from wire connectivity
• Connectivity between the transmitter and the receiver via wireless radio frequency RF up to a range of 100 meters
• Modern and beautiful Piano Black design with touch screen buttons
• Large and transparent LCD screen
• Preserving schedule and program settings despite losing power
• Holiday, temporary hold and constant hold modes for power saving or greater comfort
• Program scheduling for each day (7 days) or separate working days (5 days) and weekends (2 days), with four or six different time and temperature settings
• Temperature calibration
• Battery replacement warning
• Anti-freeze protection
• Options of installation – On wall installation / In wall installation in a socket / Wireless portability with built in stand

Specifications

• Power supply: Batteries 4xAAA LR03 1.5V
• Temperature setting range: from 5°C to 35°C
• Temperature display range: from 5°C to 40°C
• Accuracy: ± 0.1°C
• Ambient temperature: from 0°C to 50°C
• Warehouse temperature: from -10°C to 60°C
• Dimensions: 124x88x21mm
• Connection: Radio frequency RF 868 MHz, FSK

Thermostat description

Buttons

• On / Off button (short press will turn on or turn off the device); Confirmation button
• Time set button
• Settings / menu button
• Change value – increase
• Change value – decrease

Display

• Time / Temperature / Setting
• Day, Days of the week
• Heating programs
• Main display (temperature, settings, …)
• Underfloor sensor symbol
• Editing settings mode
• Thermostat is currently using Heating program schedule or is in Heating program schedule editing mode
• Manual temporary / permanent temperature set
• Thermostat has antifreeze mode active
• Heating is on
• . Thermostat is in gateway mode WIFI
• Thermostat is in AP access point mode

Installation

Wall mount (on wall, dose – socket)

• First, remove the back of the thermostat. Do that by using a straight screwdriver and carefully rise the front cover from the bottom up.
• While doing that you will notice a small flex cable attached to the back and the front of the case. Be careful not tearing it.
• You have to remove the cable from the front part of the case. Do it carefully. Now, the thermostat should be separated on two parts – front (screen) and back (electrical connection…).
• When the parts are separated, take the back part and make the electrical wiring.
• Once again, the assembly should be carried out by a qualified person and read all safety instructions and warnings before assembly. Keep main power off all the time!
• Use the electrical wiring scheme on the right side for help

Now follows the installation of the back part into the wall socket. For help use the picture below. Two screws are attached for easier installation. Be careful to install the back part the right orientation as the small “tongue” part on the bottom should be looking towards the floor.

When you’ve attached the back part on the wall socket, you can connect the back part with the front one. You can do that by carefully attaching the cable to the front part and then pushing the front part of the case on the already installed one. The thermostat should now be installed and ready for use

Possible error codes

Error code	Description
Err.2	Underfloor heating sensor is not installed. Thermostat stops Heating. – Check whether you’ve installed the sensor correctly and the sensor is the correct specifications. Also, check the sensors specifications and your thermostat advanced settings (100K, 10K)
Err.1	Sensor in thermostat is malfunctioning. Thermostat stops Heating. – Turn the device on and off. Try removing the main power supply – this should be done by a professional electrician! If that doesn’t help – turn to your point of sale or our service centres.

Using the thermostat – First steps, basics and description of functions, settings The thermostat is very easy to use but it offers many advanced functions. For a quick and easy start, the instructions will be explained in the next pages and we advise that you go through them for even easier use. By default, the thermostat has Heating schedule programs DISABLED. This means, that out of the box you can only set the permanent, constant temperature and Heating schedule programs cannot be set. If you want to enable Heating schedule programming, you’ll have to follow the part of advanced settings for setting the heating programs of the thermostat.

• Turning ON / OFF The thermostat can be turned ON or OFF by a short press on a button for turning on/off (see button description 1)
• Changing the values The values are always changed by short pressing the (changing value, button description 4) and ( changing value, button description 5) buttons.
• Displaying time and day The thermostat has an option of displaying the current time or currently set temperature of heating. With a short press on the middle menu button (button 3) you change the display from one to another.

Temporary temperature change

• Temporary temperature change means, that if you currently want to change the temperature which will stay changed until the next Heating program change (if you’re using Heating schedule programs – otherwise, a permanent, constant temperature change is made).
• For example – Currently the time is 13:00 and the Heating temperature is set to 20.0°C. You temporary change the temperature to 24.0°C and the thermostat will keep this set value until the next Heating schedule change, which you’ve set at 14:30 with temperature set at 22.0°C.
• You can activate the temporary temperature change by pressing buttons, when you’re not in any menu and the device is turned on. When you press one of those two buttons, the currently set temperature starts to blink. Now, set it to your desired value and when you’re satisfied with the temperature, stop pressing the buttons and the device will save the settings itself and start to use the new set temperature until the next Heating schedule program starts.
• If you’ve set everything correctly, the device will show symbols of a clock (using schedule, display description 7) and a hand (manual temperature change, display description 8). You can exit this function anytime by turning the thermostat off and on or by waiting for the next program to start.. The device will then show only a symbol of a clock, as the heating program schedule will be on.

Permanent (constant) temperature change

• Function of permanent temperature change means, that when the function is enabled, the thermostat ignores all of the currently set schedules of Heating programs until manually canceled and uses your manually set temperature.
• This function is automaticaly turned on when the heating schedule program is disabled in the advanced settings. When the function is enabled, a hand symbol is shown on the display.  symbol in not visible anymore.
• If you want to change the set temperature, you can do that by pressing buttons.
• This function is usefull if you’re away for holiday or a longer time and want to keep the lowest, ECO room temperature you want.

Setting the day and time

• You can set the time and date when the device is turned off (the screen displays OFF). Now hold the button for 5 seconds. Now, you’re in the date and time setting menu.
• First, you can see that hours are blinking at the top right side of the screen, which means that you’re changing this value.
• You can change the values by pressing  and move to changing the next time, date setting by pressing the button. You can set hours, minutes, day, month and year.
• When you’re done setting the day and time, press the on/off button (button 1).

Setting the Heating Schedule Programs
The condition for setting the Heating schedule is that the Heating programs are turned on (it is turned off by default) in the advanced settings. Before proceeding, check the advanced thermostat settings. Depending on the set advanced thermostat settings, you can set on how the schedule program works. In advanced settings, you can set your schedule for 7 days (each day) or just turn it off. The Heating schedule can be easily edited via the main editing menu – the thermostat must be turned on, then hold (5 seconds) the middle menu button (button description 3). Now you’re in the program editing menu. When you’re in the Heating schedule programs editing menu, you’ll see on the right side of the screen a blinking icon (sun, moon, house…) which shows for which program switch you’re currently editing the program. Also at the top of the screen, the day which you’re editing starts to blink. That means that you’re editing for the selected day. You change the values by pressing the buttons and go to the next setting with the middle menu button (button description 3). All the settings will be automaticly saved if you don’t press any button for more than 10 seconds. First you have to select for which day you’ll be setting the schedule. When you select the day, press the menu button and then you’ll proceed to setting the time of when this schedule will start. When you’re done setting the time, press the middle menu button and you’ll be setting the temperature for that schedule. Set the desired temperature and again press the menu button. Now you’re done setting the settings for the first Heating schedule switch of the program. Now a different icon on the right (sun, moon, house) should blink, which indicates that you’re editing for the next Heating program switch.
You can take a look at example of predefined Heating schedule programs on the next pages

Predefined Heating Schedule Programs tables
Below are listed the predefined Heating schedule programs. They are set with default values

Table 1 – 7 days, 6 switches (Set for each day separately

Advanced thermostat settings

The thermostat also has advanced thermostat settings for further customization of the device to your wishes and demands. You can enter the advanced settings by turning off the thermostat. The screen should show OFF. Then hold the middle menu button (button description 3) for 5 seconds. The screen will be turned on and the display will show CL and a small gear icon will appear on the bottom. That means that you’re now in the advanced settings and you’re editing the first setting. You move around the menu by short pressing the middle menu button and change the value by pressing the button. Settings are saved by short pressing the ON/OFF button. If you don’t press any button for more than 20 seconds, the device will also save the settings by itself

Step (Shown below, near the gear icon)	Display on display	Selectable values (in brackets is the factory default value)	Description
1	CL	From -6 to +6 (0)	Temperature display correction. Thermostat is factory-set to the correct temperature display, but you still have the option of adjusting the display by correcting it.
2	AH	From 20 to 70 (35)	Maximum setting of heating temperature in degrees °C. With this option, you can limit the heating temperature that can be set using the thermostat.

Step (Shown below, near the gear icon)	Display on display	Selectable values (in brackets is the factory default value)	Description
3	AL	From 5 to 20 (5)	Minimum option of setting the heating temperature in degrees °C. With this option, you can limit the heating temperature that can be set using the thermostat.
4	FH	From 20 to 70 (40)	Maximum set temperature of floor heating in °C. You can limit the maximum set floor heating temperature.
5	FL	From 5 to 20 (5)	Lowest set temperature of floor heating in °C. You can limit the minimum set floor heating temperature.
6	SEN	AL / In / OU (In)	Thermostat mode – Use of internal or external sensors. AL – The thermostat uses both sensors for temperature read – internal and external underfloor. In – Thermostat uses internal temperature sensor only. OU – Thermostat uses external underfloor temperature sensor only.
7	bL	2 / 3 (2)	Use this option to change the screen brightness. 2 – Screen backlight lasts 30 seconds; 3 – Screen backlight is always turned on
8	P51	0 / 7 (0)	Heating Schedule programs. Here you can turn on/off and set on how the heating program schedule will work. 0 – The heating program schedule is turned off; 7 – 7 days (each day separately; table 1)

Step (Shown below, near the gear icon)	Display on display	Selectable values (in brackets is the factory default value)	Description
9	ES	On / Off (Off)	Smart adaption. If you have this function enabled (On), the thermostat will start to heat before the next heating program schedule will start and with that it will achieve a more comfort way of heating. The thermostat learns regarding the last 5 days of heating conditions and how much time it took to get to the desired set temperature. For example – if it needed 30 minutes to get from 20°C to 22°C it will start heating 30 minutes before the next heating program with 22°C occurs.
10	An	On / Off (Off)	Antifreeze protection. The thermostat will turn on heating, if the temperature falls below 5°C.
11	NTC	100 / 10 (100)	100 = Sensor with 100K resistance 10 = Sensor with 10K resistance

Changing control mode – AP / WIFI thermostat mode

The thermostat has two control modes AP – means that the thermostat is in access point mode and you can see the thermostats SSID wireless network and can connect to it. You can use this mode for pairing or to DIRECT connect to the thermostat via app for testing purposes. When this mode is on, a symbol is displayed on the screen (see display description 12). WIFI / GATEWAY – means that the thermostat is connected and paired to the home wireless network and app. When this mode is on, a symbol is displayed on the screen (see display description 11). If this symbol is blinking, there’s a problem with connecting with your local wireless network.

To change modes – WIFI/GATEWAY -> AP (by doing this, the thermostat is back available for pairing with app, home wifi network,…): The thermostat must be turned ON and now hold the on/off button for 5 seconds. Symbol for WIFI should disappear and AP mode symbol should be turned on. The thermostat automatically turn on the WIFI mode when you connect the thermostat with your home wireless network and the Saswell app.

Saswell application APP – Installation, use – Step by step

If you need more help regarding the use of our APP, visit our YouTube channel Sen Controls.

Application installation On your smart phone, open the app store (Google Play Store, App Store) and search for »Thermostat« or »Thermostat Saswell«, developer Saswell. The exact name of the app is »Thermostat«. Install the app on your device.
Now you should have the icon of Thermostat visible in your applications on your phone. Press on the icon to open the app.

Using the App – local, test mode Thermostat can also be used via the app without internet access but in test mode – local mode. This means, you can only see the current room temperature and set the desired temperature but cannot set any heating schedules.

Android: To use this mode, open the app. On the top right of the screen you’ll see »DIRECT« button. Click on it and the application will start looking for nearby Saswell thermostats. All of nearby thermostats, that are in AP mode will be seen and listed. Select the one that you wish to connect by pressing on his SSID* name (thermostats SSID is also printed on the case of the thermostat starting with »THERMOSTAT-» When you click on it, you’ll be able to see the current room temperature and set the desired heating temperature via app

iOS: To use this mode, open the app. On the top right of the screen you’ll see »DIRECT« button. Click on it and now go back to your phone’s settings menu, WIFI settings. Find the SSID* of the thermostat and click on it (SSID starts with »THERMOSTAT-»). Now return to the Saswell app. Now, you should able to see the current room temperature and set the desired heating temperature via app.

Important

• To be able to access the local, test mode, the thermostat must set to AP mode. Otherwise, you won’t be able to see your thermostat.
• SSID – SSID is the name of the WIFI wireless network

Using the App – Creating a new Saswell account (registration)
To save all of your thermostats and be able to set your heating schedule programs, you have to create a new Saswell account if you don’t have one yet. You can do this easy and anonymous by:

• Open the app.
• Because you don’t have an account yet, press “REGISTER”.
• Under EMAIL enter your valid email address, where you’ll receive the account confirmation email
• Under PASSWORD enter your desired password. Write it down somewhere.
• Re-enter your desired password under RE ENTER PASSWORD
• Press REGISTER and by doing that you’re just one step away from completing the registration.
• Check your email mailbox and find the confirmation email. Click on the confirmation link and the registration is complete. If you can’t find the email, check your Spam folder.
• Now that you have your new Saswell account, use it to login to your account in the app. Under Username enter your email address used for registration and under Password enter your password. Now press login.
• You should now be in the overview screen, which should be empty, but don’t worry, as you’ve just created your account it’s time to add your first thermostat to your account

Using the App – Adding a new thermostat

Before adding a new thermostat to your account, you have to make sure that the thermostat is in AP mode. If not, turn it to AP mode using the instructions on the previous pages.
Now, open the app and login using your login information. Now, when you’re in the Overview, press + button on the top right of the screen and follow the instructions for your smart device…

Android If you own a smart device with Android operating system and have the thermostat ready in AP mode, follow these steps:

• After you pressed on + button on top right of the overview screen, you can now click on »FIND DEVICE«. Now a list of all nearby Saswell thermostats, that are ready to pair, should be listed on the screen.
• Select and press on the desired thermostat that you wish to pair. If you have more than one available, you can distinguish them by their SSID name as every Saswell app thermostat has written its unique SSID name on its housing and in app.
• After selecting the thermostat, you have to select the gateway to connect your thermostat to. The gateway is the name of SSID of your home wireless network. Select the one that is the closest to your Saswell thermostat to ensure connection quality. If your home wireless router is too far away, use a Wi-Fi extender or move the thermostat or router closer. It’s recommended to have at least two strength lines on you smart device (this is also a way to check your wireless signal strength on the location of the thermostat).
• When you’ve selected the desired wireless network, check the wifi information – wireless network name and password. Add the password, if it’s not automatically added. When you’ve completed this step, press the “CONFIG” button to connect to the network.
• The app should now show a popup “Connect device to network…” and tries to connect the thermostat to your wireless network. If the process is successfully complete, the app shows “Device connect internet success” and now you can press button “TRY NOW”. Press it.
• If everything went ok, you should see your newly added thermostat under Overview of all of your added thermostats (if there are more), named like it’s SSID (see casing of the thermostat – “SSID: Thermostat-…”.
• You’ve successfully added your new Saswell thermostat to the Saswell app

iOS If you own a smart device with iOS operating system and have the thermostat ready in AP mode follow these steps:

• After you pressed on + button on top right of the overview screen, you can now go back to your phone and go to Settings and WIFI settings.
• Your phone should list all of the available wireless networks around your phone. Select and connect to the network with the SSID name which is the same as the one on the thermostat housing “SSID: Thermostat-…”.
• Now after you’ve connected to the thermostat network, return to the Thermostat app. App should automatically see, that you’re connected to the thermostat’s network and moved on to the next step. Now you have to re-enter the
• sword for your home network – the SSID of your home network should be already filled in but the password should be empty. Enter the password to finish this step and press “SEND”.
• If the thermostat is successfully added, you should be able to see it under the Overview windows near all of your other added thermostats, if there are any. Each thermostat is named like it’s SSID, which is also visible on the thermostats housing (“Thermostat-…”).
• You’ve successfully added your new Saswell thermostat to the Saswell app.

Using the App – Renaming and deleting the thermostat

All of the newly added thermostats have generic and pre-set names. If you’d like to organize the thermostats in your home, you can easily rename each one by your preferences or remove one if you wish to re-add or just remove it from your account. You can do this by pressing on the thermostat’s name for a few seconds and a popup window should appear, asking for your choice to remove or rename the thermostat. Renaming As we wish to rename the thermostat, we select the option “Rename”. App now offers textbox to rename the thermostats name. You can enter anything you like, for example “Kitchen” or “Living room”. After you’re done, press OK. Removing As we wish to delete the thermostat, we select the option “Remove” and confirm the deletion with pressing “YES

Using the App – Setting heating schedule programs, temperature and status

After you’ve added a thermostat to your app, you can see it under Overview when you login to the app. Under overview you can see a short status of all thermostats – ECO (away) mode active or not, current room temperature, current set temperature and if the thermostat is turned off. If the thermostat is available for use (connected to your home network and visible in overview) you can press on its name to go under thermostats settings. Now you can 1) set the temporary temperature (“TARGET)” 2) see the current room temperature (“CURRENT”), 3) completely turn off the thermostat (by sliding right over the slide to power off) 4) turn on the ECO mode (“AWAY”), 5) see the room temperature history and heating history or 6) set heating schedule programs by pressing the PROGRAM button.

Turning on the ECO mode or »AWAY« mode, will turn off all of your set heating modes until turned off and will try to keep heating only up to 16°C. This mode is useful when youre away for a shorter time and would like to keep a lower room temperature in your home. To turn this mode on or off, slide the switch in the top right corner (4).

Heating schedule programs can be set by pressing on the button “PROGRAM”. This opens a new menu, which you can see on the left side. The heating schedule program can be turned on or off by sliding on top right button (1).
Now you’re setting the heating schedule for (2) selected day or days, that you can mark on point 3. When you’ve selected your desired days to set the program, you can set up to 6 daily programs (4) Select the desired daily program and by sliding up or down set the desired starting hour for the program (5). Now set the desired set temperature by pressing up or down arrows (6). When you’ve set all of the heating programs, press SUBMIT (7) to save all of your changes.
If you wish to set a temporary set temperature, return to the previous window by pressing the back arrow on the top left corner and change the desired set temperature (see previous page, point 1) by pressing on the arrows up and down. The temperature will stay on until the next heating schedule program occurs. If the heating schedule programs are disabled (turned off by sliding the point 1 on the picture on the left) you’ll be setting permanent set temperature, which will stay on until re enabling the heating schedule programs.

Reference

Download Manual:

Saswell SAS922WHL-7W-S-WIFI WifiProgrammable Thermostat User Manual

Saswell SAS922WHL-7W-S-WIFI WifiProgrammable Thermostat User Manual