SALUS SQ610 Quantum Thermostat Quick Guide

SALUS SQ610 Quantum Thermostat

Introduction

The SQ610 Quantum is a ZigBee temperature controller for wireless control of iT600 series devices, such as the KL08RF wiring centre, mini TRV head, RX10RF boiler control module. In order to control SQ610 over the Internet or via the SALUS Smart Home mobile app (ONLINE mode), it must be installed together with the UGE600 Internet gateway (sold separately). From the application level, it is possible to pair SQ610 with other system elements, e.g. Smart Plug SPE600, Smart Relay SR600 or window/ door sensor OS600/SW600. SQ610 can be used locally without an Internet connection (OFFLINE mode), however, it’s communication with other devices must be done using the CO10RF coordinator (sold separately).

THERMOSTAT SQ610 Quantum can work without Universal Gateway or CO10RF Coordinator as a standalone device.”
Full manual in PDF format is available at www.salus-controls.eu site.

Product Compliance

This product complies with the essential requirements and other relevant provisions of Directives 2014/30/ EU, 2014/35/EU, 2014/53/EU and 2011/65/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.saluslegal.com.

Safety Information

Use in accordance to national and EU regulations. Use the device as intended, keeping it in dry condition. Product for indoor use only. Installation must be carried out by a qualified person in accordance to national and EU regulations. Disconnect your equipment before cleaning it with a dry cloth.

Warning:

Please always ensure the AC 230V mains power is switched off before installing or working on any components

Package Content

1. SQ610 Quantum Thermostat
2. Mounting screws
3. Manual instruction

Before you start

Select the correct thermostat location

Mounting: to mount the thermostat you can use included accessories (mounting screws). Remove the plate from the back to mount it to the wall. After that just put the thermostat on the plate.

Please note:

The ideal position to thermostat mounting is about 1,5m under floor level far from heating or cooling sources. The thermostat can’t be exposed to sunlight or any extreme conditions like for example draft.

Wiring diagram

Symbols explanation:

• S – volt-free contact
• T – temperature sensor
• L, N – 230V AC power supply
• COM, NO – Voltage-free output
• S1,S2 Terminals:
  • air or floor temperature sensor
  • external volt-free contact to connect any ON/OFF switch or occupancy sensor (Hotel card)

LCD Icon Description

1. Menu/Settings Description + Clock
2. AM/PM
3. Temperature unit
4. Heating indicator (icon is animating when there is heating demand)
5. Cooling indicator (icon is animating when there is cooling demand)
6. RF Connection indicator
7. Internet connection indicator
8. Occupancy sensor (hotel card)
9. Key lock function
10. Standby mode icon
11. Current Temperature / Setpoint Temperature
12. Holiday mode
13. Temporary override mode
14. Settings icon
15. External / Floor temp sensor indicator
16. Schedule program number
17. Schedule mode icon
18. Day indicator/ SET information
19. Current Humidity value

Buttons Description

Buttons Description
Button	Function
	1) Menu button / Return button. 2)  In the MAIN SCREEN: Press and hold for 3 sec to change the thermostat operating mode (Schedule mode / Permanent mode / Temporary override mode). 3) In the SETTINGS SCREEN: Press and hold for 3 sec to go back without saving the changes. 4)  In the PAIRING SCREEN (in SYSTEM TYPE Menu): Press and hold for 3 sec to see other pairing options.
	„Down” Button (Decrease parameter value/moving on the menu in the ‘DOWN’ direction)
	“Up” Button (Increase parameter value/moving on the menu in ‘UP’ direction)
	1) “OK / Tick” Button (Confirm parameter value / Go to the next menu / Save settings) 2)In the MAIN SCREEN: Press and hold for 3 seconds to enter Standby mode 3)In the SETTINGS SCREEN: Press and hold for 3 sec to go back to the MAIN SCREEN & SAVE all the changes.
	In the MAIN SCREEN – press and hold these buttons together for 3 seconds to LOCK / UNLOCK the Thermostat keys).

COMPATIBILITY WITH OTHER SALUS CONTROLS DEVICES

Quantum Thermostat can work in ONLINE or OFFLINE mode. *
In the first step, you need to decide in which mode your thermostat will work.

ONLINE MODE

Universal Gateway is CONNECTED TO THE INTERNET

You can configure and use all your devices in the Smart Home App.
Download the Smart Home App on your iOS or Android device for remote access to your SALUS equipment.

OFFLINE MODE

Universal Gateway is NOT CONNECTED TO THE INTERNET
You can use your devices locally without the SmartHome App. Gateway works in this mode as a standard ZigBee coordinator.

CO10RF Coordinator – You can use the standard ZigBee network coordinator to install and use your devices.

Compatible devices

Please note:

SQ610 Quantum Thermostat can work without coordinators (ONLINE/ OFFLINE MODE) as a standalone device with the wires used.

First power-up sequence

Please note:

For easier installation, please make sure you have already added other devices to your ZigBee network, such as
Underfloor Heating Control Box (KL08RF) or Radiator heads (TRV’s) etc.

Installation

Installation in ONLINE mode

Installation in OFFLINE mode

Pairing with Wiring Centre / Control Box (Install the Wiring Centre / Control Box according to the instructions included with the product)

Pairing with TRV radiator head (Install the TRV according to the instructions included with the product)

Wired device

Please note:
Thermostat SQ610 Quantum can work without Universal Gateway or CO10RF Coordinator as a standalone device.

1. Wiring diagram for volt-free connection (e.g. boiler control):
2. Wiring diagram for 230VAC connections
3. Wiring diagram for control box connection

Please note:

Self-acting SQ610 Quantum Thermostat without application support can be easily added to the Smart Home app anytime. All settings made before adding to the application are automatically copied to the Smart Home app.

SQ610 Full menu structure

Short description of some selected functions (all functions are described in the full version of the SQ610 manual):

1. DISPLAY TEMP RESOLUTION: This function determines the resolution of the displayed temperature ( 0.5°C or 0.1°C ).
2. CONTROL ALGORITHM: This function defines how to control the room temperature. Available options are: ITLC for Underfloor Heating / Radiators / Electrical Heating (that’s an advanced algorithm for precise maintenance of room temperature), hysteresis +/-0.5°C or +/-0.25°C, THB Actuator (option recommended for systems with THB auto balancing actuators).
3. S1/S2 INPUT: A floor sensor, an external temperature sensor or an occupancy sensor can be connected to the S1/S2 input of SQ610RF. Additionally, by connecting a NO type of ON/OFF voltage-free contact, you can use this input as a OneTouch rule trigger (programmed in the Salus Smart Home app) or as a Heat/Cool changeover.
4. VALVE PROTECTION: This function activates all actuators once a week for 5 minutes (in summer, this function helps to prevent the actuators stuck).
5. INTERNAL RELAY (COM/NO): Internal relay activation or deactivation with COM/NO outputs used. Default is enabled.
6. MIN TURN-OFF TIME: Minimum switch-off time (thermostat will not send the signal for heating/cooling more often than specified in this parameter).
7. OPTIMISATION FEATURE: Optimum Start and Optimum Stop functions are energy-saving features that make the thermostat the most cost-effective (in combination with the ITLC control algorithm).
8. COMFORT WARM FLOOR: This function helps to keep the floor warm, even if the room is warm enough and there is no need to turn on the heating. Users can select 3 levels of the warm floor features. Please note it is not an economy feature, as your heating system may be ON even if there is no heating demand from the room thermostat. It is a COMFORT feature that keeps your floor warm all the time.
9. DEVICE INFORMATION: In this menu, the user can check: Software Version, RF range value, and Paired devices or also user can activate Identification mode.
10. FACTORY RESET: Here you can RESET your device to factory settings. After a successful reset device will be removed from the ZigBee network and you will need to add/pair your device again.

QUANTUM SQ610

QUANTUM SQ610
Power Supply	AC 230 V
Temperature range	5-40°C
Display temperature accuracy	0.5°C or 0.1°C
Control algorithm	ITLC SPAN (±0.25°C / ±0.5°C) THB
S1-S2 Input (multifunctional input)	Floor temperature Air temperature Occupancy sensor One Touch Changeover (heating/cooling)
Output control	COM – NO (volt-free)
Max current	3 (1) A
Communication protocol	ZigBee 2,4GHz
Mounting	Flush mounting
Working temperature	0-45°C
IP protection class	IP30
Dimensions [Width x Height x Deep]	86 x 86 x 10 mm
Thickness after mounting in a wall box φ60	10 mm

• UNIVERSAL GATEWAY:
  Connect it with Universal Gateway and set up your own SALUS Smart Home system
• SMART RADIATOR CONTROL:
  Pair it with Quantum to achieve the perfect temperature everywhere, not only beside the radiator
• SMART RELAY:
  Connect it with Universal Gateway and control  wirelessly pumps, valves,  boilers, lighting, etc

PRODUCER:
Salus Limited 6/F, Building 20E, Phase 3, Hong Kong Science Park, 20 Science Park East Avenue, Shatin, New Territories, Hong Kong
IMPORTER:
QL CONTROLS Sp. z o.o. Sp. k. ul. Rolna 4, 43-262 Kobielice

www.salus-controls.eu
SALUS Controls is a member of the Computime Group.
Maintaining a policy of continuous product development SALUS Controls plc reserves the right to change the specification, design, and materials of products listed in this brochure without prior notice.

Reference

Download Manual

SALUS SQ610 Quantum Thermostat Quick Guide

OTHER MANUALS

SALUS SQ610 Quantum Thermostat User Manual

SALUS SQ610 Quantum Thermostat Quick Guide