HTRS-RF(30) is a wireless digital room thermostat compatible with devices that are part of the iT600 series, such as: KL08RF wiring centre, TRV10RFM thermostatic radiator valve and RX10RF boiler receiver. If you want the thermostat to control the devices via Internet (Online Mode), please use the UG600 universal gateway and connect it to the SALUS Smart Home app. You can also use the thermostat to control the devices locally without Internet connection (Offline Mode) but in this case the communication between devices must be done using the CO10RF coordinator.
This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU, and RoHS 2011/65/EU. Full text of the EU Declaration of Conformity on www.saluslegal.com 2405-2480MHz; <14dBm
Use in accordance with the regulations. Indoor use only. Keep your device completely dry. Disconnect your device before cleaning it with a dry cloth.
Select the device that is going to be controlled by the thermostat and the type of Zigbee network coordinator you want to use. Install the devices according to the instructions attached to each product.
After inserting the batteries, the thermostat will display the software version and it will power up.
After the first power-up, you can choose to pair the thermostat either with underfloor heating (UFH) or with radiators (red):
Extended configuration should be used only if you want to pair the thermostat with the boiler receiver. To do so, press the buttons shown below simultaneously until all visible icons flash once.
The offline pairing method should be used by non-internet users only.
WARNING! Do not use the CO10RF coordinator with UG600 simultaneously.
WARNING! You can connect up to 6 TRVs to one thermostat.
WARNING! In a ZigBee network, you can use only one RX10RF configured as RX1 and only one RX10RF configured as RX2.
Please use the online pairing method when you are using UG600 to configure your system. Follow the on-screen instructions to complete the setup.
Once you have selected your device type, follow the onscreen instructions to complete the setup.
Go to Installer Mode, select parameter 00, and press
The LEDs on the paired devices will start to flash.
Press to exit installer mode.
If the thermostat works in AUTO mode, then the overwritten temperature (temporary override) will be maintained until next program. In manual mode and frost protection mode temperature change is permanent.
Salus Limited
6/F, Building 20E, Phase 3, Hong Kong Science Park, 20 Science Park East Avenue, Shatin, New Territories, Hong Kong
support@salus-controls.de
tel: +49 6108 8258515
technicalsupport@saluscontrols.fr
tel: +33 (0) 134 724 039
tech@salus-tech.com
tel: +44 (0) 1226 323961
www.salus-controls.eu
SALUS Controls is a member of the Computime Group Maintaining a policy of continuous product development SALUS Controls plc reserves the right to change the specification, design and materials of products listed in this brochure without prior notice.
Issue date: 03 2021
Version: V016
Download Manual
SALUS HTRS-RF(30) Wireless Digital THERMOSTAT Quick Guide
OTHER MANUALS
SALUS HTRS-RF(30) Wireless Digital THERMOSTAT User Manual
SALUS HTRS-RF(30) Wireless Digital THERMOSTAT Wiring Daigram
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…