SALUS HTRP-RF(50) Wireless Digital THERMOSTAT Quick Guide

SALUS HTRP-RF(50) Wireless Digital THERMOSTAT

Introduction

HTRP-RF(50) is a programmable wireless digital room thermostat compatible with devices that are part of the IT600 series, such as: KL08RF wiring center, TRV10RFM thermostatic radiator valve and RX10RF boiler receiver. If you want the thermostat to control the devices via Internet (Online Mode), please use the UGE600 universal gateway and connect it to the SALUS Smart Home app. You can also use the thermostat to control the devices locally without Internet connection (Offline Mode) but in this case the communication between devices must be done using the CO10RF coordinator.

Product Compliance
This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of Conformity on www.saluslegal.com.
2405-2480MHz; <14dBm Safety Information
Use in accordance with the regulations. Indoor use only. Keep your device completely dry. Disconnect your device before cleaning it with a dry cloth.

Wiring diagram

Power supply:
2 x AA alkaline batteries
S1 & S2 terminals:- external temperature sensor (air or floor)
external switch (occupancy sensor)

Mounting: surface mounting (after removing the back case)

LCD icons

1. Comfort temperature
2. Standard temperature
3. Reduced temperature
4. Auto mode
5. Party mode
6. Holiday mode
7. Frost protection mode
8. Heating Mode ON
9. RF signal
10. Internet connection
11. Cooling Mode ON
12. Manual Mode / Temporary Override
13. Current Temperature
14. Lock key
15. AM / PM
16. Day of the week
17. Hour
18. Settings
19. Low battery
20. Sensor connected
21. Program number

Button functions

Button combinations

Zigbee network coordinators

1. Online: connected to the Internet using the UG600 universal gateway.
2. Offline: with the possibility of connecting to the Internet using the UG600 universal gateway.
3. Offline: without any possibility of connecting to the Internet using the CO10RF coordinator.

Select the device that is going to be controlled by the thermostat and the type of Zigbee network coordinator you want to use. Install the devices according to the instructions attached to each product.

Power up

After inserting the batteries, the thermostat will display the software version and it will power up.

• KL08RF wiring centre
• TRV10RFM thermostatic radiator valve.

Extended configuration
Extended configuration should be used only if you want to pair the thermostat with the boiler receiver. To do so, press the buttons shown below simultaneously until all visible icons flash once.

3: Choose the device type according to the screens below:

• Undefloor heating
• Radiator heating
• RX10RF in RX1 mode
• RX10RF in RX2 mode

OFFLINE PAIRING PROCEDURE

The offline pairing method should be used by non-internet users only.
WARNING! Do not use CO10RF coordinator with UG600 simultaneously.

Pairing with the Wiring Centre

• Select on the LCD
• Open the ZigBee network.

Select the wiring centre number using (max 9). Confirm your choice by pressing .

Select the group number (offline only) using . Confirm your choice by pressing .

Select the zone number using .Confirm your choice by pressing .

Close the ZigBee network

Pairing with the TRV

WARNING! You can connect up to 6 TRVs to one thermostat.

Press and hold the button for 10 seconds. The LED will start flashing red.

Open the ZigBee network

Press to confirm the pairing with the TRV.

Press >. The LED on the TRV will flash green one time and then it will turn off.

The LCD will display the number of paired devices.Press to finish.

Close the ZigBee network

Pairing with the boiler receiver

In order to pair directly the thermostat with the boiler receiver, please follow the Extended configuration procedure.

Open the ZigBee network

Close the ZigBee network

ONLINE

Please use the online pairing method when you are using UG600 to configure your system. Follow the on-screen instructions to complete the setup.

16: Once you have selected your device type, follow the onscreen instructions to complete the setup.

Identify paired devices

Go to Installer Mode, select parameter 00 and press.

4: The LEDs on the paired devices will start to flash.

Press to exit installer mode.

Change temperature setpoint

If thermostat works in AUTO mode, then the overwritten temperature (temporary override) will be maintained until next program. In manual mode and frost protection mode temperature change is permanent.

Factory Reset

IMPORTER:
QL CONTROLS Sp. z o.o. Sp. k. ul. Rolna 4, 43-262 Kobielice

PRODUCER:
Salus Limited
6/F, Building 20E, Phase 3, Hong Kong Science Park, 20 Science Park East Avenue, Shatin, New Territories, Hong Kong

support@salus-controls.de
tel: +49 6108 8258515
technicalsupport@saluscontrols.fr
tel: +33 (0) 134 724 039
tech@salus-tech.com
tel: +44 (0) 1226 323961
www.salus-controls.eu

SALUS Controls is a member of the Computime Group Maintaining a policy of continuous product development SALUS Controls plc reserve the right to change the specification, design and materials of products listed in this brochure without prior notice.
Issue date: 03 2021
Version: V016

REFERENCE

Download Manual:

SALUS HTRP-RF(50) Wireless Digital THERMOSTAT Quick Guide

OTHER MANUALS:

SALUS HTRP-RF(50) Wireless Digital THERMOSTAT User Manual

SALUS HTRP-RF(50) Wireless Digital THERMOSTAT Wiring Diagram

SALUS HTRP-RF(50) Wireless Digital THERMOSTAT Quick Guide