Product Compliance
This product complies with 2014/30/EU, 2014/35/EU, 2011/65/EU. Full text of the EU Declaration of Conformity on www.saluslegal.com.

Safety Information
Use in accordance with the regulations. Indoor use only. Keep your equipment completely dry. Disconnect your equipment before cleaning it with a dry towel.

Installation

This accessory must be fitted by a competent person, and installation must comply with the guidance, standards and regulations applicable to the city, country or state where the product is installed. Failure to comply with the relevant standards could lead to prosecution.

Box Content

Thermostat front case
Thermostat rear case
Quick Guide
2 x fixing screws

Wiring

Note: You can wire the thermostat directly to the KL08NSB Wiring Center (purchased separately).

Mounting

Please refer to the images below for mounting your thermostat.

Terminals

Terminal	Function
	Switching Live (output)
CO	Changeover, 0V for heating or 230V for Cooling (input)
	0V normal temp mode; 230V reduced temp mode (input)

N	Neutral Input
L	Live Input

BTR230 Jumpers

Different features of the BTR230 can be switched ON or OFF with the jumpers. In order to do this please follow the table below.

Jumper	Feature	ON	OFF
COOLING	Close: Cool block disabled; Cooling enable Open: Cool block enabled; Cooling disable
SETBACK	NSB Function (2° or 4° selectable)	2⁰C	4⁰C
PWM	Pulse-Width-Modulation
VP	Valve protection

The jumpers from 1 to 5 are representing the number of actuators that you can connect to the thermostat.
After the actuators are mounted please move the jumper on the correct number (the same as the number of actuators).

Night Setback

NSB (Night SetBack) Function
NSB Mode is always ON, giving the possibility to choose a reduction between 2°C or 4°C. The NSB signal is activated every 1 second. When the signal is received the setpoint temperature will be reduced by 2°C or 4°C.

Heating and Cooling
The Heating/Cooling function is determined by the CO terminal connection.
CO 0 V = Heat mode CO 230V= Cool mode

Cooling Blocked

Cooling Blocked function

Cooling Enabled: Set the jumper to ON position. The thermostat will run in normal cooling mode. That means that it will open/close the actuators when necessary. The LED will be BLUE when the cooling function is running.
Cooling Disabled: Set the jumper to OFF position. CO terminal will be deactivated. Heat mode only.

Control Patterns
This product has a jumper to choose output control pattern, PWM output or ON/OFF output. In heating mode, there is PWM or ON/OFF control output. In cooling mode, only ON/OFF control output.

IMPORTER:
QL CONTROLS Sp. z o.o. Sp. k. ul. Rolna 4, 43-262 Kobielice
support@salus-controls.de
tel: +49 6108 8258515
tech@salus-tech.com
tel: +44 (0) 1226 323961

PRODUCER:
Salus Limited
6/F, Building 20E, Phase 3, Hong Kong Science Park, 20 Science Park East Avenue, Shatin,
New Territories, Hong Kong
T: +44 (0) 1226 323961
E: sales@salus-tech.com
www.salus-controls.eu

SALUS Controls is a member of the Computime Group Maintaining a policy of continuous product development SALUS Controls plc reserves the right to change the specification, design and materials of products listed in this brochure without prior notice.

REFERENCE

Download Manual:

SALUS BTR230(20) Non-Programmable Thermostat Quick Guide

OTHER MANUALS

SALUS BTR230(20) Non-Programmable Thermostat Wiring Diagram

SALUS BTR230(20) Non-Programmable Thermostat Quick Guide

wpx_thermostats

Next SALUS ERT2024V Non-Programmable Thermostat Wiring Diagram »

Previous « SALUS BTR230(20) Non-Programmable Thermostat Wiring Diagram

SALUS BTR230(20) Non-Programmable Thermostat Quick Guide