SALUS 091FLV2 wired Programmable Thermostat Quick Guide

SALUS 091FLV2 wired Programmable Thermostat

Introduction

091FLv2/091FLRFv2 is a programmable, weekly thermostat used to control room temperature in heating or cooling systems. Before use please read this manual carefully. Use only AA 1.5V alkaline batteries in the thermostat. Place the batteries into the battery slot located under the cover. Do not use rechargeable batteries.

Product compliance
This product complies with the following EU Directives:

• 091FLv2: 2014/30/EU, 2014/35/EU, 2011/65/EU
• 091FLRFv2: 2011/65/EU, 2014/53/EU
• 868.0 MHz – 868.6 MHz; <13dBm.

Full information is available on the website www.saluslegal.com

Safety Information 
Use in accordance with national and EU regulations. Use the device only as intended, keeping it in a dry condition. The product is for indoor use only. Installation must be carried out by a qualified person in accordance with national and EU regulations.

Technical specification

Wired thermostat 091FLv2

Power supply	2 x AA batteries
Rating max	5 (3) A
Outputs	Voltage-free NO/COM relay
Temperature range	5 – 30°C

Wireless thermostat 091FLRFv2

Thermostat supply	2 x AA batteries
Receiver supply	230 V AC 50 Hz
Receiver rating max	16 (5) A
Receiver outputs	Voltage-free NO/COM relay
Temperature range	5 – 30°C

Proper thermostat placement

Button Functions

LCD Icon description

1. Day of the week indicator
2. Heating Mode ON
3. Cooling Mode ON
4. Room / setpoint temperature
5. Temperature unit
6. Controlled device working status (e.g. boiler)
7. Temporary override
8. Eco Mode
9. Program number
10. Antifrost Mode
11. Comfort Mode
12. Program timeline indicator
13. Clock
14. Low battery indicator
15. AM/PM

091FLv2 Wiring diagram

091FLRFv2 Wiring diagram

Setting Time

• Press button to highlight the display.
• Press to set the day.
• Press to set the hour.
• Press to set the minutes.

Setting the comfort temperature

1. Pressbutton to highlight the display.
2. Press and then press
   Display will show current comfort temperature. To change this temperature, press button.
3. To confirm press button.

Setting the economic temperature 
Press button to highlight the display. Press and then press

Display will show current economic temperature. To change this temperature, pressbutton.

Programs

There are 9 programs available. Programs 0-5 are factory programs. Programs 6-8 can be defined by user.

Selection of factory (0-5) programs

1. Press to highlight the display. Select the day of the week by pressing button.
2. Press to set the program number (0-5) for the selected day.
   Program 0 is a special program. It will set the thermostat to antifrost temperature (7°C) for the full day.
3. To confirm pressbutton.
   NOTE! Label with programs descriptions is sticking on the flip side of the cover.

Choosing and programming (6-8) user programs

1. Press to highlight the display. Select the day of the week by pressing button.
2. Press to set the program number (6, 7 or 8) for the selected day.
3. Press button (each pressing one of these buttons moves the timeline by one hour and assigns a comfortable or an economic temperature).
4. To confirm pressbutton.

Service menu

Pressbutton to highlight the display. Then open service menu by holdingbutton for 5 seconds.

1. Heating mode – the relay closes the contacts when there is a need for heating (default setting).
   Cooling mode – the relay closes the contacts when there is a need for cooling (with 5 minutes delay).
   Press to select mode. To confirm your option press .
2. Heating device delay switch disabled (default setting).
   Heating device delay switch is ON (5 min)
   Select by pressingbutton. To confirm your option press .
3. Temperature span selection, possible values are 0.5°C or 1.0°C (default = 1.0°C).
   Pressto set span. To confirm your option press.
4. Measured temperature correction (value range: -3.0°C to + 3.0°C, default = 0.0°C).
   Pressto set correction. To confirm your option press.
5. Terminal output – Normally Open.
   Terminal output – Normally Closed this feature is available from 2.6 software version
   Select by pressingbutton. To confirm your option press .
   Note: The green LED is always ON when the relay output is short.
6. Pairing process inactive
   Pairing process active.
   NOTE! If you are using 091FLRFv2 pack, the pairing between the thermostat and the receiver is already done.

If you want to re-pair thermostat with the receiver, make sure that the device is disconnected from the power supply and the switches on the receiver have been set to AUTO and ON. Then connect the receiver to the power supply and wait for the red LED to light steadily. Next switch to the OFF position and again to ON position quickly. The red flashing LED will confirm entering the pairing mode.
Selectby pressingand confirm byto begin pairing process.
Display will show . The pairing process may take up to 10 minutes. Once devices are successfully paired, LED on the receiver will go solid red. Pressbutton to end the pairing process.

PRODUCER:
Salus Limited
6/F, Building 20E, Phase 3,
Hong Kong Science
Park, 20 Science Park East
Avenue, Shatin,
New Territories, Hong Kong
www.salus-controls.eu

REFERENCE

Download Manual:

SALUS 091FLV2 wired Programmable Thermostat Quick Guide

OTHER MANUALS

SALUS 091FLV2 wired Programmable Thermostat Wiring Diagram

SALUS 091FLV2 wired Programmable Thermostat Quick Guide