Robertshaw

Robertshaw RS9220 Programmable Thermostat Operational Guide

Robertshaw RS9220 Programmable Thermostat

Caution

DO NOT SWITCH SYSTEM TO COOL IF THE TEMPERATURE IS BELOW 50°F (10°C). THIS CAN DAMAGE THE AIR CONDITIONING SYSTEM AND CAUSE PERSONAL INJURY.

THERMOSTAT OPERATION

  • LCD Screen
  • Fan Switch
  • System Switch
  • Temperature Set-Point Buttons
  • User Buttons

  1. LCD Screen
    See page 4 for detailed information.
  2. Fan Switch
    Select ON or AUTO. ON will run the fan continuously. AUTO will cycle the fan on only when the heating or cooling system is on.
  3. System Switch
    Selects HEAT or COOL for your HVAC system. Selecting HEAT turns on the heat mode. Selecting COOL turns on the cool mode.
    Selecting OFF turns both heating and cooling off. Selecting EMH (for heat pumps with auxiliary heat) will lock out the compressor and control emergency/auxiliary heat.
  4. Temperature Set-Point Buttons
    Press to select the desired temperature.
  5. User Buttons
    Use these buttons to set up programming options.

THERMOSTAT QUICK REFERENCE

Caution:
When the battery icon appears, replace the alkaline AAA batteries immediately to avoid damage to your HVAC system. Freezing or overheating could occur.

Battery Door Information

Temperature Adjustment (if Using a Program Schedule)

  • Temporary Adjustment: You may temporarily change the desired temperature set-point by pressing either . The temperature will remain at this set-point until the next programmed WAKE, LEAVE, RETURN, or SLEEP event. The program schedule will then resume.
  • Program Schedule Hold: The thermostat will display HOLD and RUN SCHED on the left of the screen when you press either . You may hold the temperature at a fixed temperature set-point and override the program schedule by pressing HOLD. The thermostat will display HOLD below the temperature set-point to notify you that the program schedule hold is in effect.
  • To Return to Programming: Press RUN SCHED to return to the program schedule.

Filter Change Reminder

The thermostat can be configured to remind you when the air filter needs to be changed. The filter change reminder can be adjusted to up to 2000 hours in 50 hour increments. If the installer configured the thermostat to issue this reminder, FILTER will be displayed when it is time to change the air filter. When FILTER is displayed, you should change the air filter and reset the Filter Change Reminder by holding down the second button from the top left side of the thermostat for 3 seconds.

PROGRAMMING

Set Time of Day and Day of Week

  • Press the MENU button.
  • Press SET TIME.
  • Day of the week will be flashing. Use to select the current day of the week.
  • Press NEXT STEP.
  • The current hour will be flashing. Use to select the current hour. Note the correct a.m. or p.m. indicator is selected.
  • Press NEXT STEP.
  • The minutes will be flashing. Use to select the current minutes.
  • Press DONE when completed

Custom Programming

This thermostat can be configured to have 7 Day or 5+1+1 programming. If 7 Day is selected, all seven days will need to be programmed individually. If 5+1+1 programming is selected, Monday–Friday will be programmed together and Saturday and Sunday will need to be programmed individually. There are four time periods for each day (WAKE, LEAVE, RETURN, SLEEP). Follow the steps below to customize your program schedule

  • Select HEAT or COOL.
    Note: Heat and cool need to be programmed separately.
  • Press MENU (If menu does not appear first, press RUN SCHED).
  • Press SET SCHED.
    Note: Monday–Friday (or Monday if in 7 Day mode) will be displayed and the WAKE icon is shown.
  • Time will be flashing. Use to make your time selection for the WAKE time period for Monday–Friday (or Monday if in 7 Day mode).
  • Press NEXT STEP.
  • The set-point temperature will be flashing. Use to make your set-point selection for the WAKE time period for Monday–Friday (or Monday if in 7 Day mode).
  • Press NEXT STEP.
  • Repeat steps 4 through 7 for the LEAVE time period, for the RETURN time period, and for the SLEEP time period for Monday–Friday (or Monday if in 7 Day mode).
  • Repeat steps 4 through 8 for the Saturday WAKE, LEAVE, RETURN, and SLEEP time periods, and then again for the Sunday WAKE, LEAVE, RETURN, and SLEEP time periods for the 5+1+1 program schedule, and for each day for the 7-day program schedule

INSTALLER SETUP MENU

  • Press MENU.
  • press and hold TECH SET button for 3 seconds.
  • Configure the installer options as desired using the table.
  • Use the to change settings and the NEW STEP or
  • PREV STEP to move from one option to another.
    Note: Only press DONE key when you want to exit the Installer Setup Options.

TERMINAL DESIGNATIONS

  • W2………………..Auxiliary heat relay
  • Y……………………Compressor relay
  • G…………………..Fan relay
  • O………………….. Heat pump reversing valve energized in cooling
  • R…………………..24VAC Power
  • C…………………..The common wire from the system transformer
  • B………………….. Heat pump reversing valve energized in heating
  • W/E……………….Emergency heat relay

Customer Service

Reference

Download Manual:

Robertshaw RS9220 Programmable Thermostat Operational Guide

OTHER MANUALS

Robertshaw RS9220 Programmable Thermostat Installation Guide

Robertshaw RS9220 Programmable Thermostat Product Specifications Guide

Robertshaw RS9220 Programmable Thermostat Operational Guide

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago