Robertshaw RS9210 Programmable Thermostat Operational Mnaual

Robertshaw RS9210 Programmable Thermostat

THERMOSTAT OPERATION

• LCD Screen
• Fan Switch
• System Switch
• Temperature Set-Point Buttons
• User Buttons

z LCD Screen
See page 4 for detailed information.
Fan Switch
Select ON or AUTO. ON will run the fan continuously. AUTO will cycle the fan on only when the heating or cooling system is on.
System Switch
Selects HEAT or COOL for your HVAC system. Selecting HEAT turns on the heat mode. Selecting COOL turns on the cool mode.
Selecting OFF turns both heating and cooling off. Selecting EMH (for heat pumps with auxiliary heat) will lockout the compressor and control emergency/auxiliary heat.
Temperature Set-Point Buttons Press or  to select the  desired temperature.
User Buttons Use these buttons to set up programming options.

THERMOSTAT QUICK REFERENCE

Battery Door Information

Temperature Adjustment (if Using a Program Schedule)

• Temporary Adjustment: You may temporarily change the desired temperature set-point by pressing either . The temperature will remain at this set-point until the next programmed WAKE, LEAVE, RETURN, or SLEEP event. The program schedule will then resume.
• Program Schedule Hold: The thermostat will display HOLD and RUN SCHED on the left of the screen when you press either . You may hold the temperature at a fixed temperature set-point and override the program schedule by pressing HOLD. The thermostat will display HOLD below the temperature set-point to notify you that the program schedule hold is in effect.
• To Return to Programming: Press RUN SCHED to return to the program schedule.

Filter Change Reminder

The thermostat can be configured to remind you when the air filter needs to be changed. The filter change reminder can be adjusted to up to 2000 hours in 50 hour increments. If the installer configured the thermostat to issue this reminder, FILTER will be displayed when it is time to change the air filter. When FILTER is displayed, you should change the air filter and reset the Filter Change Reminder by holding down the second button from the top left side of the thermostat for 3 seconds.

PROGRAMMING

Set Time of Day and Day of Week

• Press the MENU button.
• Press SET TIME.
• Day of the week will be flashing. Use to select the current day of the week.
• Press NEXT STEP.
• The current hour will be flashing. Use to select the current hour. Note the correct a.m. or p.m. indicator is selected.
• Press NEXT STEP.
• The minutes will be flashing. Use to select the current minutes.
• Press DONE when completed

Custom Programming
This thermostat can be configured to have 7 Day or 5+1+1 programming. If 7 Day is selected, all seven days will need to be programmed individually. If 5+1+1 programming is selected, Monday–Friday will be programmed together and Saturday and Sunday will need to be programmed individually. There are four time periods for each day (WAKE, LEAVE, RETURN, SLEEP). Follow the steps below to customize your program schedule

• Select HEAT or COOL. Note: Heat and cool need to be programmed separately.
• Press MENU (If menu does not appear first, press RUN SCHED).
• Press SET SCHED. Note: Monday–Friday (or Monday if in 7 Day mode) will be displayed and the WAKE icon is shown.
• Time will be flashing. Use to make your time selection for the WAKE time period for Monday–Friday (or Monday if in 7 Day mode).
• Press NEXT STEP.
• The set-point temperature will be flashing. Use to make your set-point selection for the WAKE time period for Monday–Friday (or Monday if in 7 Day mode).
• Press NEXT STEP.
• Repeat steps 4 through 7 for the LEAVE time period, for the RETURN time period, and for the SLEEP time period for Monday–Friday (or Monday if in 7 Day mode).
• Repeat steps 4 through 8 for the Saturday WAKE, LEAVE, RETURN, and SLEEP time periods, and then again for the Sunday WAKE, LEAVE, RETURN, and SLEEP time periods for the 5+1+1 program schedule, and for each day for the 7-day program schedule

INSTALLER SETUP MENU

• Press MENU.
• press and hold TECH SET button for 3 seconds.
• Configure the installer options as desired using the table.
• Use the to change settings and the NEW STEP or
• PREV STEP to move from one option to another.
• Note: Only press DONE key when you want to exit the Installer Setup Options.

TERMINAL DESIGNATIONS

• W2………………..Auxiliary heat relay
• Y……………………Compressor relay
• G…………………..Fan relay
• O………………….. Heat pump reversing valve energized in cooling
• R…………………..24VAC Power
• C…………………..Common wire from system transformer
• B………………….. Heat pump reversing valve energized in heating
• W/E……………….Emergency heat relay

Customer Service

• +1.800.304.6563
• Technical Service +1.800.445.8299
• HVACCustomerService@robertshaw.com
• www.robertshaw.com
• 352-00301-001352-00312-001 Rev. B
• © 2021 Robertshaw Controls Company.
• Robertshaw® is a trademark of Robertshaw Controls Company.

Reference

Download Manual:

Robertshaw RS9210 Programmable Thermostat Operational Mnaual

OTHER MANUALS

Robertshaw RS9210 Programmable Thermostat Installation Manual

Robertshaw RS9210 Programmable Thermostat Product Specifications Guide

Robertshaw RS9210 Programmable Thermostat Operational Mnaual