Reliance STAT100015 240V Wired and RF Programmable Thermostat Installational Manual

Reliance STAT100015 240V Wired and RF Programmable Thermostat

Specification

• Power source: 100-240VAC 50/60Hz
• Load current output: 250VAC 3(2)A
• Temperature setting range: 5~35°C
• Display accuracy: 0.1°C
• Setting accuracy: 0.5°C
• Storage temperature: -10~60°C, 0~90%RH
• Ambient temperature: 0~50°C, 0~80%RH
• Wireless frequency: Lora 868MHz

Note:
For connecting to the internet you must use the Reliance Valves Gateway – GWAY100001.

Important safety information
Read all of the information in this manual before installing this thermostat. removing, cleaning, or servicing this thermostat. Only a professional contractor should install this thermostat. All wiring must conform to local and national building and electrical codes and regulations. If the system is not operating properly, check the wiring and replace the fuse if necessary. Use this thermostat only as described in this manual.

Thermostat display

1. If the icon is not shown then WiFi is not connected If the signal is lost after connection the icon will flash
2. Weeks icon
3. Mode: Room mode, floor mode, dual temperature mode
4. Room temperature/time display
5. Manual mode
6. Programming mode
7. Zone number – If flashing then the connection to the wiring center has been lost
8. Key lock
9. Boiler ON/off
10. Frost protection
11. Holiday mode
12. Settings menu
13. AM/PM
14. Sleep mode
15. Away mode
16. Back home mode
17. Wake up
18. Temperature setting/Boost display

ON/OFF function
Press ‘ ’ to turn the thermostat ON. Press and hold ‘ ’ again to turn the thermostat is OFF.

Key lock function
In the main display interface, press and hold ‘ ’ ‘ ’ at the same time to activate or cancel the key lock. When activated, no keys can be used. Then the thermostat will display ‘ ’.

Boost function
Press ‘ ’ to switch the set temperature or boost control. When the display shows ‘ ’, press ‘ ’ ‘ ’ to select boost hour. The length of time the heating will be boosted is displayed. When the time elapses the screen returns to the temperature display. Press ‘ ’ to cancel and go back to the temperature display setting.

Holiday mode
With the power on, press ‘ ’ to switch between manual mode, programming mode, and holiday mode. After selecting holiday mode ‘ ’ will display and will run at 16°C. Press ‘ ’ to cancel holiday mode. The boost function can be used during the holiday periods.

Open window function
If the room temperature drops 6°C in 4 minutes, the open window function will activate and display ‘ ’, then turn down all heating. When the room temperature increases by 2°C the thermostat will return to normal operation. Press any button to cancel the open window function while it is active.

Anti-seize function
If the thermostat has not been activated for over 1 week then to prevent the valve and pump from seizing, the thermostat will run the system for 5 minutes.

Frost protection
In frost protection mode, when the temperature drops below what has been selected, the thermostat will start heating until the temperature has been raised by 3°C.

Intelligent function
The intelligent function adjusts the starting time for home heating according to the temperature measured within the building. It preheats your rooms to the temperature according to your schedule.

Time Proportional and Integral (TPI) display
intervals, adjusting firing duration with demand, to maintain set room temperatures. It can provide great cost savings.

Time setting

Press and hold ‘ ’ for 4 seconds, press ‘ ’ to select the year, month, day, time scale, and time, press ‘ ’ ‘ ’ to adjust the setting, and press ‘ ’ to confirm. If there are no actions for 10 seconds, the thermostat will return to the temperature display mode. Press ‘ ’ to check the time, year, month, day.

Setting the date and time for the initial start-up
Plug in the power supply. Press ‘ ’ or ‘ ’ to set the year, press ‘ ’ to set the month, day, time scale, and time, and press ‘ ’ ‘ ’ to adjust the setting.

Program setting
Program setting: 4/6 period programming optional (factory default: 6 periods). When the thermostat is on, press and hold ‘ ’ to enter the programming mode. Press ‘ ’ or ‘ ’ to select the programming week (5+2, 5+1+1, or 7 individual day optional). Press ‘ ’ to enter time setting mode. Press ‘ ’ or ‘ ’ to select time, and press ‘ ’ to enter temperature setting mode, Press ‘ ’ or ‘ ’ to select temperature. Press ‘ ’ to save and exit. If no buttons are pushed for 10 seconds, then the thermostat will exit the program sets automatically.

Default programming (6-period programming)

（4-period programming)

In the programming state, press and hold ‘ ’ ‘ ’ at the same time to restore factory settings, display ‘

Operation mode

Programming mode (The factory default is programmable)
The thermostat will run according to the pre-set schedule. The screen will show ‘the’

Manual mode
From the programming operation mode, press ‘ ’ to enter the manual mode, and the screen will display ‘ ’. Press ‘ ’ or ‘ ’ to immediately adjust the temperature and save automatically.

Temporary hold mode
The thermostat will keep the room at the temporary set temperature and will resume the program operation mode when you enter the next program. In programming operation mode, press ‘ ’ or ‘ ’ to enter the temporary hold mode, and the screen display ‘ ’. Press ‘ ’ or ‘ ’ to immediately adjust the temperature and save automatically.

Alarm instructions

Connecting the thermostat and wiring center

1. With the thermostat powered off, press and hold the on/off button for 4 seconds to enter pairing mode (the display should show “rFl “).
2. Press the on/off button again to send a signal to the wiring center (the display should show “–“)
3. On the Wiring Centre, press and hold the pairing button for 3 seconds to enter pairing mode
4. Use the Wiring Centre pairing button to select the desired zone, indicated by the LED
5. Leave the wiring center for 3 seconds. The LED should flash to indicate it is paired with the thermostat
6. Once paired, the wiring center LED will move to the next available zone. Press and hold the pairing button once again to exit the pairing mode
7. The thermostat is now connected to the chosen zone

Installation

1. Install the base
2. Mounting screws
3. Install the panel
4. Finish

Wiring diagram

Wiring diagram for 230V connections: Suggest cable is not over 1.5mm

Configuration menu
With the thermostat turned off, press and hold ‘‘ to enter the configuration menu. Press ‘ to select different parameters. Press’ ‘ to adjust the parameters. Press and hold ‘ ‘ for 3 seconds, and display ‘dEF’ indicates all the configuration settings have reverted to the factory default setting. The thermostat will return to ‘OFF’ mode if no buttons are pushed within 10 seconds.

Gateway specification

• Adapter output: 5V — 1A
• Working temperature: -10°C~55°C
• Working humidity: 10%-90%(no condensation)
• Wifi frequency: 2.4G Wi-Fi
• Wireless frequency: Lora 868MHz
• Dimensions: 60.5 × 60.5 × 16.1mm

Connecting the App

Download and register
Click App Store (click Android application market) Search for ‘Reliance Controls’ and download

Login

When you finish the registration, log into your email and click on the link to activate your account. Your APP is now ready to use.

Connecting to the Gateway

Tips: First, please turn on the location of your phone. Press and hold the reset key of the gateway until the light turns red and blinks.

1. Enter the ‘HOME’ interface of Click ‘Wireless thermostat’.
2. Click ‘Wireless thermostat’.
3. Enter your Wi-Fi account and password. Click ‘Next’
4. Tick ‘Confirm and proceed’, then click ‘Next’ (Follow the instructions to reset the device)
5. Adding device…
6. Click ‘Done’, it means the gateway has been added successfully

Tips
Before pairing the gateway, you need to power on the gateway. When pairing a gateway, the mobile phone and the gateway must connect to the same network.

Add thermostat
Before adding the thermostat, press and hold ‘ ’ for 3 seconds, press ‘ ’ ‘ ’ to select ‘ ’, then press ‘ ’ to enter the code match status and it will display ‘ ’ then follow these steps to connect the app.

1. Click ‘ Add subdevice
2. Adding device
3. Added successfully Click ‘Done’.

APP Setting-programming

APP Setting-Multi-day Programming

Remove devices

Voice command

After waking up the speaker you can say:

Amazon Alexa

• Alexa, turn on the bedroom.
• Alexa, raise the bedroom by 1 degree.
• Alexa, drop the bedroom by 1 degree.
• Alexa set the bedroom to 16 degrees.

Google Assistant

• Ok, Google, turn on the bedroom.
• Ok, Google, set the bedroom to 16 degrees.

Tips:
The bedroom is the device’s name. You can name it during the device setup. The temperature graduations and format must be the same in the speaker and the thermostat.

Reliance Worldwide Corporation (UK) Limited
Horton Road
West Drayton
UB7 8JL
United Kingdom
Tel: +44 (0) 1895 449233

Reliance Worldwide Corporation (UK) Limited reserves the right to make changes to the product which may affect the accuracy of the information contained in this leaflet. www.reliancevalves.com

Reference

Download Manual:

Reliance STAT100015 240V Wired and RF Programmable Thermostat Installational Manual

Other Manual:

Reliance STAT100015 240V Wired and RF Programmable Thermostat Product Specifications Guide

Reliance STAT100015 240V Wired and RF Programmable Thermostat Installational Manual