Pro1 Technologies T805 Non-Programmable Thermostat Operational Manual

Pro1 Technologies T805 Non-Programmable Thermostat

Pro1 Technologies
P.O. Box 3377
Springfield, MO 65808-3377
Toll Free: 888-776-1427
Web: www.pro1iaq.com
Hours of Operation: M-F 9AM – 6PM Eastern

Caution Equipment damage hazard. Do not operate the cooling system if the outdoor temperature is below 50 ˚F (10 ˚C) to prevent possible compressor damage.

Thermostat Operation

1. LCD Display
   See page 6 for details about this display read out.
2. Glow in the dark light button
   The glow in the dark light button will self illuminate for several hours after exposure to ambient light. This button turns on the display light when pressed.
3. Fan Button
   Select ON, AUTO or IAQ. The ON setting will run the fan continuously. The AUTO setting will cycle the fan on only when the heating or cooling system is on. IAQ will enable IAQ FAN MODE, if selected.
4. System Button
   Selects the operation mode on your HVAC system. Selecting HEAT turns on
   the heat mode. Selecting COOL turns on the cool mode. Selecting OFF turns both heating and cooling off. Selecting AUTO will turn the HEAT or COOL on as needed.
5. Temperature Setpoint Buttons
   Press the buttons to select the desired room temperature.
6. Button / Battery Door
   See page 4 for further information.

Thermostat Quick Reference

Battery Door Information

Caution: 
When the battery icon appears replace your AA batteries immediately. Failure to do so may result in your heating & cooling system becoming inoperable. Freezing or overheating can occur.

Important: 
The low battery icon is displayed when the AA battery power is low. Whenever the thermostat detects low battery voltage from the AA batteries, the low battery icon will begin flashing on the screen for 21 days (if the batteries are not changed). If the batteries are not changed 22 days after the thermostat detects low battery voltage, the thermostat screen will only show the flashing battery icon until buttons are pressed. If the batteries are not changed 43 days after the thermostat detects low battery voltage, the thermostat screen will only show the flashing battery icon until buttons are pressed and the set points will offset to 85°F/29°C in cooling and 55°F/13°C in heating. At this stage, set point changes can be made temporarily but, the set points will change back to defaulted values after a 4-hour period. The thermostat will continue to perform this low battery flashing, temperature offset condition until the internal voltage threshold is reached. When the thermostat internal voltage threshold is reached, all relays will be opened and the thermostat will become inoperable until new batteries are installed.

Thermostat Quick Reference

1. Day of the week
2. Heating Setpoint: Displays the user selectable setpoint temperature.
3. Time and day of the week
4. Indicates current room temperature
5. Indicates if heating or cooling equmipment is running
6. Hold Indicator: Displayed when the thermostat is inpermanent hold
7. Low Battery Indicator
8. Energy Efficient Leaf: Indicates the setpoint termperature chosen is an efficient choice.
9. Keypad Lockout: Indicates the thermostat is in keypad lockout
10. Program Menu Buttons: Shows different options during programming.
11. Fan Button: Changes the fan operation between Auto, IAQ, and On.
12. System Button: Changes the system operation between Off, Cool, Auto, Heat, and Emergency Heat based on system tech setting.

Programming

Set Time (If using programming)
Follow the steps below to set the day of the week and current time:

1. Press the MENU button.
2. Press SET TIME.
3. Day of the week will be flashing. Use the key to select the current day of the week.
4. Press NEXT STEP.
5. The current hour is flashing. Use thekey to select the current hour. When using 12-hour time, make sure the correct a.m. or p.m. choice is selected.
6. Press NEXT STEP.
7. Minutes are now flashing. Use the key to select current minutes.
8. Press DONE when completed.
   Important: You will see a TECH SETUP option after the MENU key is pressed. This TECH SETUP key is for installer configuration and should NOT be changed unless you consult your professional heating and air conditioning technician.

Set Program Schedule For Four Time Periods

(WAKE, LEAVE, RETURN, SLEEP)
To customize your 5+1+1 Program schedule, follow these steps:

Weekday:

1. Select HEAT or COOL with the system switch.
   Note: You have to program heat and cool each separately.
2. Press the MENU button (If menu does not appear first press RUN SCHED).
3. Press SET SCHED.
   Note: Monday-Friday (Monday if in 7day) is displayed and the WAKE icon is shown. You are now programming the WAKE time period for that day.
4. Time is flashing. Use thekey to make your time selection for that day’s WAKE time period.
   Note: If you want the fan to run continuously during this time period, select ON with the FAN key.
5. Press NEXT STEP.
6. The setpoint temperature is flashing. Use theto make your setpoint selection for that day’s WAKE period.
7. Press NEXT STEP.
8. Repeat steps 4 through 7 for that day’s LEAVE time period, RETURN time period, and SLEEP time period.

Saturday:
Repeat steps 4 through 7 for the Saturday WAKE time period, for the Saturday LEAVE time period, for the Saturday RETURN time period, and for the Saturday SLEEP time period.

Sunday:
Repeat steps 4 through 7 for the Sunday WAKE time period, for the Sunday LEAVE time period, for the Sunday RETURN time period, and for the Sunday SLEEP time period.
To customize your 7 day Program Schedule, repeat steps 4 through 8 for the Tuesday, Wednesday, Thursday, Friday, Saturday and Sunday time periods.

A Note About Programmable Fan:
The programmable fan feature will run the fan continuously during during any time period when it is programmed to be on. This is the best way to keep the air circulated and to eliminate hot and cold spots in your building.

Features

Temporary & Permanent Hold Feature

Temporary Hold:
The thermostat will display HOLD and RUN SCHED on the bottom of your screen when you press the key. If you do nothing, the temperature will remain at this setpoint temporarily for 4 hours. After this, the program setpoint will then replace your temporary setpoint.
Permanent Hold:
With a temporary hold set, if you press the HOLD key at the bottom of your screen, you will see HOLD appear below the setpoint temperature in the display. The thermostat will now permanently stay at this setpoint and can be adjusted using the keys.

To Return To Program:
Press the RUN SCHED key at the bottom of your screen to exit temporary and permanent holds.

Keypad Lockout Note: 
If appears in the display, then the keypad is locked. All or some of the keys will not work. Hold the and keys for 3 seconds to remove the lock. Use the same procedure to lock the display

A Note About Auto Changeover:
When in Auto you have the ability to switch between auto heat or auto cool by pressing the system key. This can be done once the current mode has reached its setpoint. For example: if in auto heat, the heat setpoint must be satisfied before the thermostat will allow you to switch to auto cool. You can switch out of auto by holding down the system key. To get back into auto, you must toggle the system key to auto.

Features

Filter Change & Other Reminders 
If your HVAC contractor has configured the thermostat to remind you when the air filter needs changed, you will see a reminder in the display when your air filter needs to be changed.

Resetting The Filter Change Reminder: When the reminder is displayed, you should change your air filter and reset the reminder by holding down the Set Time/Next Step button of the thermostat for 3 seconds.

Warranty Information

Warranty Registration 
Your new thermostat has a 5 year limited warranty. You must register your thermostat within 60 days of installation. Without this registration the warranty period will begin on the date of manufacture. For warranty issues please contact the HVAC professional that installed this product. You can register your new thermostat in 2 ways:

Online 
Go to the company website, select warranty registration and fill out a short registration form.

Mail 
Complete the form below and mail it to the address shown.

Warranty Registration

• Name:
• Address:
• City:
• State:
• Zip:
• Thermostat Model:
• Date Installed:
• Complete form and mail to:

Thermostat Warranty Registration
Pro1iaq
P.O. Box 3377
Springfield, MO 65808-3377
www.pro1iaq.com

Reference

Download Manual:

Pro1 Technologies T805 Non-Programmable Thermostat Operational Manual

OTHER MANUALS

Pro1 Technologies T805 Non-Programmable Thermostat Installational Manual

Pro1 Technologies T805 Non-Programmable Thermostat Product Specifications Guide

Pro1 Technologies T805 Non-Programmable Thermostat Operational Manual