Moes

Moes ZHT-006 Zigbee Smart Thermostat User Manual

Moes ZHT-006 Zigbee Smart Thermostat

For Water Heating/Boiler/Electric Heating
Thank you for purchasing our products, please read the following terms before installation and use: Please confirm that this product is suitable for your heating equipment before installation;

  • Before installation or maintenance, please make sure to keep the power off;
  • Please strictly follow the wiring diagram for wiring installation;
  • Installation to the wall, please confirm that the fasteners are suitable for this product;
  • do not pull the cable too hard, otherwise the product will be damaged;
  • If a hard plastic wire is used in the installation process, it must be bent to an appropriate angle in advance;
  • please arrange for professionals to install;
  • Please contact the after-sales service for equipment failure, please do not try to repair it yourself;
  • After installation, please refer to this manual to check again to ensure normal and safe use, and keep this manual properly.

ABOUT YOUR THERMOSTATS
The BHT- 006 range has been developed to control electric underfloor, water heating or water/ gas boiler systems.  These units are designed for use in commercial, industrial,  civil and domestic properties

MODEL DEFINITION

  • GA: Water heating, 5A
  • GB: Electric floor Heating, 16A
  • GC: Water/Gas Boiler, 5A
  • L: Backlight
  • N: Modbus Communication
  • W: Wifi
  • S2: Both internal sensor and floor external sensor
  • For example: BHT-006GA

In the box you will find

  • Thermostat 1pc Screws 2pc
  • User Guide 1pc Wall plate 1pc
  • QC Passed 1pc (Floor sensor is Optional)

(Floor sensor is Optional)

  • Power Supply: 95~240 VAC, 50~60 Hz
  • Current Load: 5A (water heating, gas boiler), 16A (electric heating)
  • Sensor: NTC3950, 10K
  • Accuracy: ±1°C
  • Set Temp. Range: 5-35°C
  • Room Temp. Range: 5-99°C
  • Display Temp. Range: 5~99°C
  • Ambient Temp.: 0~45°C
  • Ambient Humidity: 5~95% RH (Non Condensing)
  • Storage Temp.: -10~45°C
  • Power Consumption: <1.5W
  • Timing Error: <1%
  • Shell Material: PC+ABS (Fireproof)
  • Installation Box: 86*86mm Square or European 60mm Round Box
  • Wire Terminals: Wire 2×1.5mm² or 1×2.5mm²
  • Protection Class: IP20
  • Buttons: Capacitive Touch Buttons

FEATURES

On Appearance

  1. LED display, more friendly interface;
  2. Touch operation buttons, smoother interaction;
  3. The ultra-thin embedded panel perfectly fits all kinds of walls;
  4. The borderless small rounded corner design is simple and atmospheric;
  5. Compatible with standard 86mm square cassettes and 60mm European cassettes to meet all installation environments;

On Functionality

  1. Rich function options, Modbus, WIFI, keycard, etc., to meet all your needs;
  2. Strict temperature control accuracy (±1℃) to provide the warmth you want;
  3. Power off protection, save all your settings safely;
  4. Provide weather information and humidity display
  5. Preset adjustment of 5+1+1 mode in a week, programma-ble setting of 6 time periods a day, green energy saving, Less cost, more intelligent and environmental protection;
  6. Support the creation of product local groups/shares to achieve unlimited centralized control of the number of products/ multi-terminal control;
  7. Perfect access: Tmall Genie, Amazon echo, Google Home, full experience new voice control method;

DIMENSION:(mm)

BEFORE WIRING AND INSTALLING

  1. Read these instructions carefully. Failure to follow them could damage the product or cause a hazardous condition.
  2. Check the rathings given in the instructions and on the product to make sure the product is suitable for your application.
  3. Installer must be a trained, experienced service technician.
  4. After installation is complete, check out product operation as provided in these instructions.

CAUTION
Electrical Shock or Equipment Damage Hazard. Can shock individuals orshort equipment circuitry. Disconnect power supply before installation.

WIRING

Note:

  • GA is for water heating;
  • GB is for electric heating;
  • GC is for water/gas boiler;
  • NTC and Modbus is optional.

INSTALLATION

Your thermostat is suitable for istallation within a standard 86mm pattress box or European 60mm pattress box.
Step 1. Keep power off. See Fig 1.
Step 2. Remove the mounting plate by pushing the LED assembly. See Fig 2.

Step 3. Connect power supply, load into the appropriate  terminals.
(see “Wiring your thermostat” for details and Fig 3). Step 4. Fix the mounting plate into the wall with screws in the box. See Fig 4.

Step 5. Fix the thermostat body and the mounting plate by the lower button. See Fig 5.
Step 6. Installation complete. See Fig 6.

HOME SCREEN QUICK REFERENCE
Note:
The weather and humidity will be synchronized within 1 hour after the device is connected to the Internet for the first time, and the weather will be synchronized every hour thereafter.Press the / in the power-on state to display the humidity and set temperature.

OPERATION

  1. Power On/off: Press to turn the thermostat on/off.
  2. Function & Programmable Touch to change between manual mode and programmemode. In manual mode, will show on the display, In programmable mode, will show on the display.
  3. Setting Temperature In the programming mode, the temperature setting and time setting will be locked. If the user wants to adjust, he must first adjust the thermostat to manual mode by pressing the key.
    In the mode of manual, press to set the desired temperature.
  4. Adjusting/Setting the Clock Press to set minute, hour and weekday. By using the . Press once more to confirm and exit.
  5. Locking your Thermostat Press and hold the for 5 seconds to lock/unlock your thermostat. In item 3 of high senior options, you can select full lock or half lock.
  6. Adjusting/setting the Program Schedules When Wi-Fi connection is made, your thermostat will automatically accept the program schedule made via the APP on your device.

If the schedule is set through the APP, after the APP completes the schedule setting, the thermostat needs to be turned off once. If the thermostat does not establish a Wi-Fi connection, manually set the schedule see below for detailed instructions: To set the program schedules throughyour thermostat (NOT via your smartphone/tablet) simply follow theinstructions as below: Please note: Setting the programme schedule through your thermostatcan only be carried out if there is no WiFi connection between yourthermostat and smartphone/tablet.

  • Press icon four times in a row. You can see “MON TUE WED YHU FRI” and , and the minutes of time are flashing. Use to set the minutes;
  • Press the icon again, the hour of the time will flash, set the hour by ;
  • Press the icon again, the temperature setting will flash, set the temperature by ;
  • This completes the setting of periods1. In the same way, complete the settings of periods2, 3, 4 and 5 (display periods1,2), 5 (display periods3, 4).
  • Press the icon once more to enter the Saturday schedule settings (you will see the SAT in the upper left corner of the screen).
  • Repeat the above process to set the period and temp. and Sunday schedule.
  • Press the icon once more to confirm and exit.

Default settings for program schedule

A separate schedule may be set for weekdays (Mon–Fri) and for weekends (Sat or Sun).

Method Two
Use APP for one week of programming settings, please refer to the second page “Programming your thermostat”

Checking the Temperature of Floor Sensor
Press and hold the arrow for 5 seconds to display the temp. of floor sensor.

Preparation for use

Download MOES App

MOES App is upgraded as much more compatibility than Tuya Smart/Smart Life App, functional well for scene controlled by Siri, widget and scene recommendations as the fully new customized service.
(Note: Tuya Smart/Smart Life App still works, but MOES App is highly recommended)

Registration or Log in

Enter the Register/Login interface; tap “Register” to create an account by entering your phone number to get verification code and “Set password”. Choose “Log in”if you already have a MOES account.

ZigBee CONNECTION
Ensure the device is within the effective signal coverage of your smart ZigBee gateway for successful connection into the ZigBee gateway in MOES APP.

Method One
Scan the QR code to configure the network guide.

  1. Make sure your MOES APP has successfully connected to a Zigbee gateway.

Method Two:

  1. Make sure your Smart MOES Smart APP has successfully connected to a Zigbee gateway.
  2. Reset:When the thermostat is off, press and hold the “ ” until the thermostat screen flashes quickly and displays the and then operate according to the following figure.
  3. nter the gateway.Please follow the picture below to finish as “Add subdevice→LED already blink,and the connecting will take about 10-120 secondsto complete depending on your network condition.
  4. Add the device successfully, you can edit the name of the device to enter the device page by click “Done”.
  5. Click enter the device page to enjoy your smart life with home automation.

APP operation interface description (heating thermostat)

Simplement Exception Handling

SERVICE

  1. During the free warranty period, if the product breaks down during normal use, we will offer free maintenance for the product.
  2. Natural disasters/man-made equipment failures, disassembly and repair without the permission of our company, no warranty card, products beyond the free warranty period, etc., are not within the scope of free warranty.
  3. Any commitment (oral or written) made by the third party (including the dealer/service provider) to the user beyond the warranty scope shall be executed by the third party.
  4. Please keep this warranty card to ensure your rights.
  5. Our company may update or change the products without notice. Please refer to the official website for the updates.

RECYCLING INFORMATION
All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19 / EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities. Correct disposal
and recycling will help prevent potential negative consequences for the environment and human health. To find out where these collection points are and how they work, contact the installer or your local authority.

WARRANTY CARD
Product Information
Product Name__________________________________________ Product Type___________________________________________ Purchase date__________________________________________ Warranty Period________________________________________ Dealer Information______________________________________ Customer’s Name_______________________________________ Customer Phone________________________________________ Customer Address______________________________________

Maintenance Records

  • Failure date
  • Cause Of Issue
  • Fault Content
  • Principal

Thank you for your support and purchase at we Moes, we are always here for your complete satisfaction, just feel free to share your great shopping experience with us. If you have any other need, please do not hesitate to contact us first, we will try to meet your demand.

EVATOST CONSULTING LTD
Address: Suite 11, First Floor, Moy Road Business Centre, Taffs Well, Cardiff, Wales, CF15 7QR Tel: +44-292-1680945
Email: contact@evatmaster.com
AMZLAB GmbH Laubenhof 23, 45326 Essen
Made In China Manufacturer: WENZHOU NOVA NEW ENERGY CO.,LTD Address: Power Science and Technology Innovation Center, NO.238, Wei 11 Road, Yueqing Economic Development Zone, Yueqing, Zhejiang, China Tel: +86-577-57186815After-sale Service: service@moeshouse.com

Reference

Download Manual:

Moes ZHT-006 Zigbee Smart Thermostat User Manual

Moes ZHT-006 Zigbee Smart Thermostat User Manual

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago