MOES 3.0 Radiator Thermostat Instruction Manual

MOES 3.0 Radiator Thermostat

Information about this manual

Please read this manual completely and carefully before starting to use the device. The manual contains important information about the intended use of the device. Especially observe the safety notes. Keep the manual for later consultation. If you hand over the device to other persons for use, please hand over the operating manual as well.

Product Description

A thermostatic radiator valve (TRV) is a self-regulating valve fitted to hot water heating system radiator, to control the temperature of a room by changing the flow of hot water to the radiator. With the TRV TV02 you can conveniently adjust the room temperature between 5-30 °C , and save more than 15% of energy. The radiator thermostat fits to all common radiator valves and is easy to mount-without having to drain any water orintervene in the heating system. The additional boost function enables the radiator to be heated up quickly for a brief period of time by opening the valve for 5 minutes.

There will be a pleasant room temperature right away because of the radiated heat.

Start-up

Before we get started

• 2 x AA batteries are required for TRV to work, please get prepared.
• Temperature is shown in degrees Celsius.

Before we get started

• Insert 2 new LR6(mignon/AA) batteries in the battery compartment, making sure they are the right way around.

The service life of new alkaline batteries is approximately 1.5 years. A battery symbol( ) on the display indicates that the batteries need to be replaced. After removing the empty batteries, wait approx. 1 minute before inserting the new ones. This device does not support operation with ones. This device does not support operation with rechargeable batteries.

Run adaptive
The display of ‘InS’ with the rotating ‘ ‘ shows that the motor is still travelling back.

• When ‘AdA’ is shown in the display, the radiator thermostat can be installed on the valve. After installation, press the pair button to run Adaptive.
• The display of ‘AdA’ with the rotating ‘ ‘shows that an press the pair button to run an adaptive adapting run to adapt the thermostat to the valve.
  If the adapting runs are initiated before installation, press pair button and the motor travels back to the ‘InS ‘ position. button and the motor travel back to the ‘InS ‘ position.
  Pair/Boost button and the motor similarly travel back to the ‘InS ‘ position.

Installation of the radiator thermostat

The radiator thermostat is easy to install and can be done without draining heating water or intervening in the heating system. No special tools are required, nor does the heating have to be switched off.
The ring nut attached to the radiator thermostat can be used universally and without accessories for all valves with a thread size of M30 x 1.5 from the most popular
manufacturers such as: Danfoss Heimeier MNG Junkers Landis&Gyr (Duodyr) Honeywell-Braukmann Oventrop Schlösser Comap Valf Sanayii Mertik Maxitrol Watts Wingenroth (Wiroflex) Idmar54 R.B.M Tiemme Jaga Siemens
By means of the adapters in the delivery, the device can be installed on radiator valves of type Danfoss RA, Danfoss RAV and Danfoss RAVL.

Unscrew your existing radiator thermostat

No worries, water will not leak during this process.

M30 x 1.5
Screw the TV02 smart radiator thermostat directly onto the radiator if the connector type is M30 x 1.5(picture shown as below). You can adjust the angle to make the led facing the viewer properly.

• Rotate the thermostat dial to the maximum value, the max value maybe 6 or 8.
• Check the © is active.
• Install the device.

Danfoss RAVL Valve

• Check the © is active.
• The valve bodied have elongated notches around their circumference, which ensure that the adapter is properly seated when it snaps on: snap on the adapter completely,so that the pins inside the adapter are lined up with the notches on the valve.
• Install the adapter,Plane A is aligned with Plane B.
• Install the round tube into the device.
• Install the device.

 

Danfoss RAV Valve

• Check the is active.
• The valve bodied have elongated notches around their circumference, which ensure that the adapter is properly seated when it snaps on: snap on the adapter completely,so that the pins inside the adapter are lined up with the notches on the valve.
• Install the adapter,Plane A is aligned with Plane B.
• Union nut.
• Install the device.

Danfoss RA Valve

• Rotate the thermostat dial to the maximum value, “N” Align Dial.
• Check the is active.
• The valve bodied has elongated notches around its circumference, which ensure that the adapter is properly seated when it snaps on: snap on the adapter completely,so that the pins inside the adapter are lined up with the notches on the valve.
• Install the adapter, Plane A is aligned with Plane B.
• Union nut.
• Install the round tube into the device.
• Install the device.

M28x1.5mm

1. Select the length of the ejector rod according to the following brands or valve sizes, and the size of the ejector rod is 15 / 17 / 19 / 24mm.
2. To install the ejector rod with the correct size into the the hole.
3. To install the adapter onto M28 * 1.5 valves;

Giacomini

To install the adapter onto the Giacomini valve in the correct direction;2. To install the GIA ejector rod into the hole ;

caleffi

1. Open the valve flow to the maximum, as shown in pic
2. To install the adapter onto the Caleffi valve in the correct direction;

Use the Ejector rod
Due to the dimensional and assembly tolerance of the metal valve, it may result in the following situations:

1. When the device is failure, F2 is displayed 2. The metal valve cannot be fully closed and is kept heating all the time
   Handling method : Please use the ejector rod 1.6mm (1) first, if the above two situations still exist, try to use the ejector rod2.6mm(2) instead.

Interface display

when you see the LCD screen is showing information as below, the radiator thermostat is ready for configuration. If not, please uninstall and re-install the batteries and redo step 4.
To press the reset button to change the digital display direction for your choice.

Software Installation

Download App

MOES APP is upgraded as much more compatibility than Tuya Smart/Smart Life APP functional well for scene controlled by Siri, widget and scene recommendations as the fully new customized service.
(Note: Tuya Smart/Smart Life APP still works,but MOES APP is highly recommended)

Register Or Login

Enter the Register/Login interface; tap “Register” to create an account by entering your phone number to get verification code and “Set password”. Choose “Log in “if you already have a MOES account.
Add Thermostat Radiator Valve

• Open MOES App, use your phone number or email address to register and login. Tap + on the top right, choose Gateway. Control->Wireless Gateway (Zigbee) and simply follow the inbuilt setup wizard for device installation and configuration.
• after the Zigbee smart gateway hub is added successfully, you can add the sub-device on the gateway hub interface.
• Long press Pair button on the radiator thermostat for 5 seconds until the Zigbee signal icon flashes, which means the device has entered the pairing mode.
• The blue LED indicator of gateway hub flashes during pairing mode.
• when the radiator thermostat is successfully added, the blue LED indicator will extinguish within 1 second, the device Zigbee signal is always on.

Product Features

Auto Mode
In automatic mode, the temperature is controlled in accordance with the set heating profile. Manual changes are activated until the next point at which the profile changes. Afterwards, the defined heating profile will be activated again. To activate the automatic mode, please proceed as follows:

• Press the mode button to select the. icon.
• Default temperature: 17°C and 21°C.
• Temperature range: 5-30 °C, step: 0.5 °C.
• App operation: Click the auto mode icon in the App control panel.

Manual Mode
In manual mode, the temperature is controlled in accordance with the current temperature set via knob button. The temperature remains activated until the next manual change. To activate the manual mode, please proceed as follows:

• Press the mode button to select a ( ) icon.
• Default temperature: 20°C.
• Temperature range: 5-30°C, step: 0.5 °C.
• App operation: Click the manual mode icon in the App control panel

Holiday Mode
When you go out or go to a party, you will use the holiday mode. The holiday mode will automatically start at the set time starting point and run the holiday temperature. When the holiday mode is not activated, and you want to view the holiday mode settings, please press the Mode button to view, the holiday mode icon will flash for 5 seconds and then it will automatically return to the auto mode.lf you want to end your holiday mode earlier, press the Mode button to cancel.
App operation: Click the Mode icon to switch to the holiday mode in the App control panel, and switch to any other mode to cancel the holiday mode.
Open Window Detection
The device automatically stop heating when it detects a sudden temperature drop(5°C in 5 minutes as default). This is usually caused by an opened window or door and the open window icon will display OPEn)on the device. The device will operate according to the preset window. Press the pair button to cancel.
App operation: Click the open window icon in App control panel to cancel the window opening function.

• The open window detection only operates in automatic mode and manual mode.

Offset Temperature
As the temperature is measured on the radiator thermostat, the temperature distribution can vary throughout a room. To adjust this, a temperature offset of ‡5 °C can be set. If a nominal temperature of e.g. 20 °C is set but the room presents with only 18 °C, an offset of -2°C needs to be set. In app settings, the offset temperature is O degrees by default. To adjust the offset temperature, please proceed as follows:
App operation: Click the offset icon (#) in settings.
Eco and Comfortable Temperature
The comfort and Eco temperature icon make switching between comfort and Eco temperature simple and user friendly. These have been set at the factory at 21°C (comfort temperature) and 17°C (Eco temperature).
App operation: Click the Comfortable()/Ecol () temperature icon in the App control panel to select the corresponding temperature mode.
Even in auto mode, the temperature can be changed at any time using the button. It will then remain the same until the next point at which the program changes.

Child Lock
The operation of the device can be locked to avoid settings being changed unintendedly.g. through involuntary touch).
To activate/deactivate the child lock, please proceed as follows:
App operation: Click the child lock icon in the App settings screen. The device display “LOC”
Anti-Freezing Mode
You can use this function when you go out in winter or when you are not at home for a long time. When this function is activated, the temperature in the house is kept at 8 °C ,the device display “AF” press the pair button to cancel.
App operation: Click the anti-freezing icon() to turn on/off the function in the App settings screen.
Note: Once this function is activated, other functions are not available unless the function is deactivated.
Heating stop (Power Saving) Mode
Battery life can be prolonged by switching the heating off.
To achieve this, the valve is closed fully. To activate the heating stop, the device display”HS”, press the pair button to cancel. please proceed as follows:

App operation: Click the Heating stop icon () to turn on/off the function in the App settings screen.
Note: Once the function is activated, other functions are not available unless the function is deactivated.
Anti-Calcification (Descaling) Protection
The equipment will automatically run for a period of time every week to prevent calcification of the valve.
Boost
Sometimes people go home earlier than usual, and the rapid heating function will make you feel the warmth of the room faster. When activated, the valve will be fully opened for 5 minutes. The heating of a room takes longer than 5 minutes, but the heat given off by the radiator can be felt immediately.

• The boost function is activated . The remaining time for the function will be counted down in seconds(‘299’ to ‘000’).
• after these 5 minutes have elapsed, the actuator changes to the mode which was previously activelau- to/manual) with the previously set temperature.
• End this function ahead of time, press the pair button to cancel.

App operation: Select the mode of the APP interface to activate the boost.Click the Boost icon (a in the App control panel to cancel the boost function.

Setting

Click the settings icon() in the App control panel.
Date
when the device is successfully paired with the phone, the device time is synchronized with the phone time.
Week Programming Stage
In this menu item, you can create a heating profile with heating and cooling phases according to your personal needs. You can set up to ten stages of temperature every day. The factory default is five stages.

• Click the week programming stage icon () in the App control panel.
• select single days of the week, all weekdays, the weekend or the entire week for your heating profile.
• Click time to select the end time of each period, and click temperature to select the required temperature.
• time range: 00:00-24:00, step: 10 minutes.
• Temperature range: 5-30 °C, step: 0.5 °C.

Open Window
Click the open window icon([) in the App settings screen.

• Select the desired temperature.
• Temperature range: 5-30°C, step: 0.5°C.

Comfortable Temperature
Click the comfortable temperature icon () in the App settings screen.

• select the desired temperature.
• Temperature range: 5-30 °C, step: 0.5 °C.

developed by Amazon, and is capable of voice interaction. Smart radiator thermostat works with Alexa to allow you to regulate the temperature of each room in your system by using a wake-word and an instruction. The wake-work is “Alexa” followed by an instruction such as “increase temperature.” Currently, Amazon has made interaction and communication with Alexa only available in English. Alexa requires explicit instructions. You must inform Alexa of the room to which you wish to address followed by an instruction, such as “increase temperature.” If no specific room is mentioned, Alexa will ask you which room you want to address, and then will increase the setpoint temperature by 1°C only based on the room reply from you. If you want the setpoint temperature to increase by 4°C in the living room, you must explicitly state to Alexa to”increase the temperature in the living room by 4°C.”
Note: If Alexa is asked to increase the temperature by 2°C, then Alexa will add 2°C to your set-point. If the ambient temperature is already >2°C above the current set-point then the actual temperature will not change and smart radiator thermostat will not turn the heating ON.
Example: If the current set-point is 16°C, the current room temperature is 19°C and you ask Alexa to increase the temperature by 2°C – the current set- point will change to 18°C but the heating will not start because the room temperature is already higher than 18°C.
Common commands for Alexa

• Listed below are common commands used with Alexa:
• discover Devices:”Alexa, discover devices.”
  Reduce Temperature:”Alexa, decrease the DEVICE NAME by 4 degrees”/”Alexa, make it cooler in here.”
• Increase Temperature: “Alexa, increase the DEVICE NAME by 3 degrees” /”Alexa, make it warmer in here.”
• set Temperature: “Alexa, set the DEVICE NAME to 20 degrees.”
• Get Temperature: “Alexa, what is the DEVICE NAME temperature?”
• Get Set Point: “Alexa, what is the upstairs set to?”
  Note: Alexa considers the smart thermostat and room names as devices.

Set an automation scenarios linkage

If you have a door sensor installed in your home, then you can realize an automation scenarios linkage between TRV and door sensor.
Under “Automation” in the “Smart” page, click”+” on the upper right corner, you will see a page called

• Create Smart that will guide you through the setting.
• Here, we take When device status changes setting.
• after you click When device status changes, you will see all the devices you added to the Tuya Smart app.
• select Smart Door Sensor-»Select Function->Smart Door Sensor->ON/OFF->Set up Task->Run the device->TRV-> Open Window Detection->ON/OFF->Save->Next->Save.
• A prompt box “Automation created.Start using it?” will pop up, select” Yes” you can see all the automation scenarios you’ve created.
  When the door/window sensor is opened, the Tuya Smart app interface will pop up a message that the door/window the sensor is turned on, and anthe icon will appear on the TRV device interface.

Low Battery

When the battery power is less than 12%, the low power prompt icon (bRE) will be displayed. Please replace the battery as soon as possible, When the the device only displays (bR’Ithe device is not available.

Reset

Press the reset buttons for 5 seconds, the device will display “FAC”. The device run reset. After the device runs reset, the data will not be saved, the device needs to be repaired.

Troubleshooting And Maintenance

Technical Data

• Batteries: 2x 1.5 V LR6/mignon/AA
• Temperature range: 5-30°C
• Display: LED
• Maximum radiated power: 10dBm
• Dimensions(W x H x D):56.5*56.5*100 mm
• Weight: 190g(incl. batteries)/140g(nincl. batteries)
• Working temperature: -10°C- 40°C
• Working environment: Indoor
• Safety :CE/ROHS
• Frequency: 2.4GHz
• Degree of protection: Ip20
• Battery life: 1.5 years

Package contents

1. 1 ZigBee Radiator Thermostat
2. 2 1.5V mignon/LR6/AA batteries (Optional) 1 Adapters for Danfoss(RA,RAV and RAVL), M28×1.5mm • Caleffi. Giacomini, Ejector rod
3. 1 Screw for adapter
4. 1 Operating manual

Instructions for disposal

Do not dispose of the device with regular domestic waste!
Electronic equipment must be disposed of at local collection points for waste electronic equipment in compliance with the Waste Electrical and Electronic Equipment Directive.
The device is not a toy, do not allow children to play with it. Do not leave packaging material lying around.
Plastic films/bags, pieces of polystyrene, etc. can be dangerous in the hands of a child.

Used batteries should not be disposed of with regular domestic waste! Instead, take them to your local battery disposal point.
This device complies with the EN62368/EN300328/ EN301489 of the CE Rules.
This device complies with the ROHS 2.0 Rules.

SERVICE

1. During the free warranty period, if the product breaks down during normal use, we will offer free maintenance for the product.
2. Natural disasters/ man-made equipment failures, disassembly and repair without the permission of our company, no warranty card, products beyond the free warranty period, etc., are not within the scope of free warranty
3. Any commitment (oral or written) made by the third party (including the dealer/service provider) to the user beyond the warranty scope shall be executed by the third party
4. Please keep this warranty card to ensure your rights
5. Our company may update or change the products without notice. Please refer to the official website for updates.

RECYCLING INFORMATION

All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19 / EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities.
Correct disposal and recycling will help prevent potential negative consequences for the environment and human health.
To find out where these collection points are and how they work, contact the installer or your local authority.

WARRANTY CARD

Product Information

• Product Name.
• Product Type.
• Purchase Date
• Warranty Period.
• Dealer Information
• Customer’s Name.
• Customer Phone
• Customer Address

Failure Date :Cause Of Issue : Fault Content : Principal
Thank you for your support and purchase at we Moes, we are always here for your complete satisfaction, just feel free to share your great shopping experience with us.
If you have any other needs, please do not hesitate to contact us first, we will try to meet your demand.
FOLow US

UK

EVATOST CONSULTING LTD
Address: Suite 11, First Floor, Moy Road Business Centre, Taffs Well, Cardiff, Wales, CF15 7QR
Tel: +44-292-1680945
Email: contact@evatmaster.com

AMZLAB GmbH
Laubenhof 23, 45326 Essen
Made In China
Maker:
WENZHOU NOVA NEW ENERGY CO.,LTD
Address: Power Science and Technology Innovation Center, NO.238, Wei 11 Road, Yueqing Economic Development Zone, Yueging, Zhejiang, China
Tel: +86-577-57186815
After Service Email: service@moeshouse.com

REFERENCE:

DOWNLOAD MANUALS:

MOES 3.0 Radiator Thermostat Instruction Manual

MOES 3.0 Radiator Thermostat Instruction Manual