OPTIONS SELECTION
At the back of the thermostat, there are 3 selection switches to set at your preferences. The temperature in °C or °F, time in 12 or 24 hours, and Early Start function.
TO SET TIME AND DAY
Press on DAY, HOUR and MIN buttons to adjust time and day.
TO RECORD THE
Select chosen setpoint temperature by using
TO RECORD THE
Select chosen setpoint temperature by using
TO RECORD THE
To program the Vacation temperature, select the desired degree using the
OPERATING MODES
NOTE: The “Problems and Solutions” section at the end of this user’s guide will help you to correct your problems during the installation. This thermostat has been designed to operate with any installation which has a RESISTIVE load not exceeding 4000 W (16.67 A) @ 240 VAC such as electric baseboards, radiant ceilings and floors, electric con vectors, etc. It is not compatible with a low voltage controller used by a central heating system. Electricians or experienced technicians should install the thermostat. This thermostat is designed to be used with a self-protected heating system equipped with thermal cut off and circuit breaker.
PARTS INCLUDED
Power-up
Note: The On/Off switch set to Off will place the thermostat in sleep mode. Ideal for summertime.
Connecting wires and mounting thermostat
Connect the rear thermostat wires to the 240 V LINE and to the load using solderless connectors for copper wires. See schematic diagram. Push the excess wire back into the electrical box to prevent interference with the thermostat. Secure the thermostat using two (2) 6-32 screws. Once the thermostat is properly installed, return power to heating system.
The TH110A-DP-P has two (2) operating modes.
MANUAL (
This mode allows you to maintain a constant temperature in the room.
AUTOMATIC ( )
Memory back-up
In the event of a power failure, an internal circuit will maintain the programming and the time. But only the time could have to be set if power failure is more than 2 hours.
Early Start function
The thermostat is providing a built-in function enabling it to calculate the optimum time to start the heating system to achieve the desired temperature setting at the programmed time. This function could start the heating system as early as 6 hours prior to the programmed time. To enable this function, set the switch E.S. to “ON” at the back of the thermostat
Programming the time and day
Programming the Comfort, Economy and Vacation settings
The Comfort
To program your settings
The TH110A-DP-P allows 4 setting changes for each day of the week. There are no pre-set programs.The programs are tailored to perfectly adapt to your life style. The principle is very simple. For each day, enter the time at which you wake up (P1), the time you leave for work (P2), the time you arrive back home (P3) and the time you go to bed (P4).
Program | Mode | Time |
1 | Wake-up time | |
2 | Leaving time | |
3 | Return time | |
4 | Bed time |
To Program your Schedule
To Erase a Program :
Select the program using PGM and Day buttons, and press on Clear button. The time field displays –:– when the program is inactive
Example 1 : Comfort period from 7:00 AM to 10:30 PM Economy period from 10:30 PM to 7:00 AM
Identical schedule for all days of the week.
Example 2 : Comfort period: Monday to Friday from 6:15 AM to 8:15 AM and from 5:00 PM to 10:00 PM. Saturday & Sunday from 7:30 AM to 11:00 PM.3
Schedule/Day | MON. | TUES. | WED. | THU. | FRI. | SAT. | SUN. |
PROG. 1 | 6:15 AM | 6:15 AM | 6:15 AM | 6:15 AM | 6:15 AM | 7:30 AM | 7:30 AM |
PROG. 2 | 8:15 AM | 8:15 AM | 8:15 AM | 8:15 AM | 8:15 AM | — | — |
PROG. 3 | 5 PM | 5 PM | 5 PM | 5 PM | 5 PM | — | — |
PROG. 4 | 10 PM | 10 PM | 10 PM | 10 PM | 10 PM | 11 PM | 11 PM |
To modify the Saturday and Sunday schedules:
Temporary or permanent temperature bypass
This operation allows you to temporarily modify the room temperature while you are in the Automatic mode. Simply press on
Mode button.
If you wish to immediately return to the programmed settings, press on Mode button twice.
All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of original installation or 18 months from the date of manufacture, except special components as noted below which are warranted against defects in workmanship and materials (see medallion levels below) from date of installation. This warranty does not apply to damage from accident, misuse or alteration; nor where the connected voltage is more than 5% above the nameplates voltage; nor to equipment improperly installed or wired or maintained in violation of the products installation instructions. All claims for warranty work must be accompanied by proof of the installation or purchase. The customer shall be responsible for all costs incurred in the removal or reinstallation of products, including labor costs and shipping costs incurred to return products to the Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be returned to the nearest Marley authorized service center or the Marley Engineered Products Service Center and we will repair or replace, at our option, at no charge to you with return freight paid by Marley. It is agreed that such repair or replacement is the exclusive remedy available from Marley Engineered Products. If the product requires replacement, but an identical model is no longer available, Marley Engineered Products will select a comparable item. the above warranties are in lieu of all other warranties expressed or implied and all implied warranties of merchantability and fitness for a particular purpose that exceed the aforesaid expressed warranties are hereby disclaimed and excluded from this agreement. Marley engineered products shall not be liable for consequential damages arising with respect to the product, whether based upon negligence, tort, strict liability or contract. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. For the address of your nearest authorized service center, contact Marley Engineered Products in Bennettsville, SC, at 1-800-642-4328. Merchandise returned to the factory must be accompanied by a return authorization and service identification tag, both available from Marley Engineered Products. When requesting return authorization, include all numbers shown on the products.
No display | • Circuit breaker is open • Power failure • The thermostat switch is in Off position | • Check 240 VAC presence at the thermostat • Put the switch in On position |
The thermostat is loosing the time but not the programming | • Power failure more than 2 hours | |
Room temperature shown is wrong | • A draft is nearby the thermostat | • Eliminate the draft |
Heating system always on | • Bad installation | • Check installation |
The thermostat displays heating but heating system is not turned on | • Bad installation | • Check installation • Check 240 VAC presence at the heating system |
Programs do not change as you want | • Incorrect programming hours • Wrong programming mode selected | • Check actual time in AM & PM as well as program times (AM is not displayed) • Make sure the operating mode is set to AUTO |
DOWNLOAD MANUALS:
Marley TH110A-DP-P Programmable Thermostat Installation Instruction
Marley TH110A-DP-P Programmable Thermostat Installation Instruction
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…