Kontakt-Simon

Kontakt-Simon DTRNW.01-11 Digital thermostat User Manual

Kontakt-Simon DTRNW.01-11 Digital thermostat

Product Marking

TECHNICAL DATA

  • Voltage 230V AC (+10% / -20%) / 50Hz
  • Load current 10A 2300W 2-pole with outer sensor (DTRNSWZ…)
  • 16A 3600W 1-pole with outer sensor (DTRNSZ…)
  • 16A 3600W 1-pole (DTRNW…)
  • Temperature regulation range 5 ÷ 40°C
  • Antifreeze Protection programmable (default +5°C)
  • Type of operation automatic
  • Method regulation ON-OFF
  • Type of sensor inner (air) – all types outer (floor) (sensor MGF47k), length: 3m
  • Night Setback programmable (default reduced by 5°C in 7 hours)
  • Weight 94g (128g with sensor)
  • Height of installation 1.0 ÷ 1,5 m
  • Protection class IP20
  • Reference standards PN-EN 60730-1

APPLICATION

  • The Temperature Regulator with Night Setback and Special Floor Protection Function is designed to control underfloor heating systems, electric heaters, etc. in a manner assuring maintenance of constant temperature.
  • Total power of the connected load may not exceed 2300W (DTRNSWZ…) or 3600 (DTRNSZ…, DTRNW…)
  • Load of higher power shall be connected through an additional contactor.
  • The Temperature Regulator 10A 2-pole (DTRNSWZ…) switch guarantees complete disconnection of the load circuit from the network.
  • The Temperature Regulator automatically detects if an external temperature sensor is connected.
  • If an external floor-or air sensor is connected, the internal temperature sensor is automatically set out of service.
  • The Temperature Regulator can be mounted by use of screws in flush-mounted Ø60mm installing boxes and surface boxes and in multiple-box set Simon54 Premium.

INSTALLATION RECOMMENDATIONS
The regulator should be installed on a wall 1,0 ÷ 1,5 m above the floor level, in a heated room in a place assuring free air circulation (see the figure ‘Method of Installation’). It should not be exposed to direct influence of other sources of heat (e.g. the sun), to draughts (close to windows, doors etc.) or water. Attention should be paid to correct connection of power supply, i.e. a phase conductor to L terminal and a neutral conductor to N terminal. A terminal for connection of a protection conductor enables maintenance of protection circuit continuity. Temperature Regulator is stablied about 30 min., after connect of power supply.

STARTING UP

ON/OFF. On /Off-button

Even in OFF position, while in Thermostat Modus Antifreeze Temperature Function, is still active.

Thermostat / Regulator Modus

Choose forth and back between Thermostat and Regulator: button     simultaneously for

3 sec.

NOTE: whatever switching on Regulator Modus adjust A parameter to value: 10%.

The interval for control of Regulator: P7 parameter Button: increase the temperature (Thermostat)

increase A parameter(1÷99%) (Regulator) Button: lower the temperature       (Thermostat) lower A parameter (1÷99%)    (Regulator)

The desired temperature shows up for 5 sec. before returning to display the actual temperature  [°C] (Thermostat) or value [%] (Regulator).

Regulator Modus in use is seen in pic.1.

Night Setback in Thermostat Modus only Press button for 3 sec until the Green LED flashes.

If Green Light, the Night Setback is activated. quick push-on button , cancels the Night Setback for this day but returns automatically to Night Setback again next day. For permanent canceling, enter into parameter P3.

Antifreeze

When Thermostat Modus is chosen, and the Thermostat being turned OFF, and the Display shows FS (Freezing Security), the Thermostat Antifreeze Function will however connect the “Heating Elements” controlled by the Thermostat. In case temperature measures below P2 parameter, the Thermostat turn on the Heating Elements preventing frost damages.

 

NOTE!

In Regulator Modus, the Antifreeze Function will not be activated when the Thermostat being turned OFF.

Explanation of Display Information

·  Display ① shows continually the actual temperature at the moment

·  By pressing the button quickly, the set temperature shows up

·  Dot ② in the display indicates floor or wall sensor is connected

·  Dot ③ indicates that the Thermostat is in regulator Modus

·  Red LED      indicates that the load is connected/on

·  Yellow LEDindicates Day Modus

·  Green LED indicates Night Setback Modus.

Lowering the temperature with set value (i.e. 5°C), and 50% in Regulator Modus

Child Safety

Press the ON/OFF button     for 8 seconds to activate the Child Safety, and the display acknowledge by short flashing. For cancelling this function, repeat the same

procedure.

Calibration (Menu P0)

Place a reliable thermometer close to the Thermostat and adjust the Thermostat by using  button to harmonize the temperature of the Thermostat with the thermometer. The result will

automatically by saved after 10 seconds.

Maximum Limit for wooden floor

Contact the supplier of the floor material for further information about the maximum temperature.

Set this recommended temperature in Menu P6.

Pic. 1. Example Uout in Regulator Modus:

DIAGRAM OF TEMPERATURE REGULATOR CONNECTION TO THE ELECTRICAL SYSTEM

METHOD OF INSTALLATION

Caution: Disconnect the power supply before installing the temperature regulator. Installation should be carried out by a person with suitable qualifications.

Caution: The wires should be connected to the terminals before the plate closes.

PARAMETER SETTINGS

How to enter the menu Press the Button and Minus-button for 5 sec. until shows up in the display
Maneuvering between the parameters Push the Button
Editing parameters Push  or – button     for setting new values
Save new settings Being automatically saved after 10 sec.
Return to Factory Settings Push and hold buttons simultaneously for a minimum of 3 sec.
Menu Parameter Settings Fact. Setting
P0 Calibrating temperature Adjustable +/-5°C in according to the “master” thermometer 0 °C
P1 Antifreeze 1 = On / 0= Off 1
P2 Set Antifreeze Temp. 1÷20 °C (only valid in Thermostat Modus) 5 °C
P3 Night Setback 1 = On / 0= Cancel Night Setback 1
P4 Hours in Night

Setback

1÷23 7 hours
P5 Lowering temp. in

Setback

1÷20 °C (In Thermostat Modus and 50% in Reg.

Modus)

5 °C
P6 Max. Floor Temp 5÷40 °C 28 °C
P7 Interval for control of temp/regulating 1÷20 min. 15 min.
P8 Maximum Limit 1 = On / 0 = Off / 2 = air *) 1
PA Floor Variants 00=47k, 01=12k, 02=15k, 03=10k, 00=47k
Pb Display Brightness 0÷50 (0 means bright and 50 means dark) 20

Reference

Download manual:

Kontakt-Simon DTRNW.01-11 Digital thermostat User Manual

Kontakt-Simon DTRNW.01-11 Digital thermostat User Manual

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago