King Electric

King Electric ESP230 Thermostat WIRING INSTRUCTIONS

King Electric ESP230 Thermostat

WIRING INSTRUCTIONS

DANGER ! ELECTRIC SHOCK OR FIRE HAZARD
READ ALL WIRE SIZING, VOLTAGE REQUIREMENTS AND SAFETY DATA TO AVOID PROPERTY DAMAGE AND PERSONAL INJURY

DISPLAY CHANGE

Fahrenheit to Celsius: On the bottom edge of the thermostat, there are air vents. In one of the vents on the left side, just behind the illumination switch, there is a larger opening with a pin collector attached. With needle nose pliers, pull the connector off.
This will put the thermostat into the metric Celsius mode. Turning off power to stat completes reset.

DIMENSIONS

  1. To wire the thermostat determine which pair of wires are coming from the breaker panel and which pair lead to the heater.
  2. With wire nuts attach the blue wire (white wire on 120 Volt model ESP120) into the pair of white wires in the junction box.
  3. Take a black lead from the circuit breaker panel and attach it to the black lead on the thermostat. This will provide power to the thermostat, LCD display, backlighting and heater relay.
  4. Take the black lead that goes to the heater and attach it to the red lead on the thermostat. This will provide power to the heater when the thermostat calls for heat.
  5. Remove cover of thermostat by holding back of thermostat and, with a finger and thumb on the top and bottom of the thermostat, pull cover towards you evenly to remove cover and expose mounting holes and buttons.
  6. Push the wires carefully into the junction box making sure no wires are pinched or will get in the way of the screws mounting the thermostat. Now attach the thermostat to the wallbox with the #6- 32 screws provided.
  7. Hold thermostat into wallbox and place screws in top and bottom mounting hole and attach to wallbox.
  8. Turn on power and test by increasing set point to higher than room temperature by tapping the up button. There will be up to a 3 minute delay in turning on. The indicator light will turn on and you will here a small click and at the same time and the heater should be on. Turn the thermostat down by tapping on the down arrow.

PROGRAMMING INSTRUCTIONS

Set Date Set Date
Upon initial power-up, the thermostat will be flashing.

  • Press the ARROW buttons to stop flashing.
  • Press the “CLOCK” button, a day will flash, then press the ARROW buttons to set today’s day

Set Time

  1. Press the CLOCK button, the hour will flash, then press the ARROW buttons to set the hour.
  2. Press the CLOCK button again to set the minute with the ARROW buttons.
  3. To exit, press the “SET” button

View Current Progra

  1. Press the “PROG” button to view the P1 temperature or Preset 1 setting for that day.
  2. Press the “PROG” button multiple times to scroll thru presents for P2, P3, and P4.
  3. Press the “SET” button to resume normal operation

Energy Saving Schedule

  • P1 Morning wake-up program
  • P2 Daily away from home program
  • P3 Evening home program
  • P4 Nightly sleep program

Your customized schedule

Program Adjustments

  1. Press the “SET” button and the “PROG” button at the same time. This puts you into Program mode and the days will be flashing.
  2. Press the ARROW buttons to select all seven days or one at a time.
  3. Press the “PROG” button to highlight the time.
  4. Press the ARROW buttons to adjust time.
  5. Press the “PROG” button again to set the temperature for that specified time.
  6. Repeat these steps for all Presets: P1, P2, P3, and P4.
  7. When you reach P1 again, press one of the ARROW buttons to change the day and repeat Programming.
  8. For P2, P3, & P4 if all the days are identical for that temperature, select all seven days for that P number.
  9. Press the “SET” button to resume normal operation.

Vacation Hold

For extended days of absence:

  1. Press the ARROW buttons to set temperature.
  2. Press the “HOLD” button until d:01 displays in the time window.
  3. Press the ARROW buttons until your number of days on vacation is displayed. Up to 99 days can be programmed.
  4. To stop vacation hold press “SET” button and normal operation is resumed.

Permanent Hold

To permanently hold the temperature:

  1. Press “HOLD” button. 1
  2. Press ARROW buttons to set temperature.
  3. To stop permanent hold press “SET” button and normal operation is resumed.

When looking at the bottom of the unit the switches are as follows:

  • upper left: backlight
  • upper right: system on/off
  • lower right: temperature sensor

Programming tech support: (800) 603-5464ext 111
info@king-electric.com

Other manuals:

King Electric ESP230 Thermostat GENERAL INFORMATION
King Electric ESP230 Thermostat INSTALLATION AND MAINTENANCE

King Electric ESP230 Thermostat WIRING INSTRUCTIONS

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago