DANGER!
ELECTRIC SHOCK OR FIRE HAZARD
READ ALL WIRE SIZING, VOLTAGE REQUIREMENTS, AND SAFETY DATA TO AVOID PROPERTY DAMAGE AND PERSONAL INJURY
This thermostat is designed to provide the highest level of accurate temperature control for residential line voltage electric heating in 120 or 208/240 volt. Almost all electric heaters installed as original equipment in a residential application will be 208 or 240 volt. It is very rare that a home, apartment or condominium would be wired with all 120 volt heaters. Check your voltage to make sure you have the right thermostat for your heater voltage. A 2 pole or double-wide circuit breaker at the panel would indicate that you should use the 240 volt model. A single pole or single wide breaker would indicate a 120 volt circuit. There are some exceptions to this rule so checking with a voltmeter is the only way to know for sure. Be safe and smart, electricity can cause severe injury or death.
The thermostat will provide years of comfort control for your family for small fan driven electric heaters, baseboards, radiant ceiling, wall panel heaters, cove heaters, or any line voltage resistance heating systems that do not have an electric motor over 1/3 hp. The thermostat will be warm to the touch on top. This the electronics operating, it also provides air currents across the face of the thermostat that help it sense room temperature better.
This precision electronic thermostat will sense the room air at the bottom of the thermostat by a thermistor. This very sensitive sensor will send information to the microprocessor. As the temperature drops, the information it sends will indicate if heat is needed. To reduce any undesirable fast on/off cycles, the processor has a built in 1 to 3 minute delay. This will save energy and provide the best control of a space. This thermostat dose not require batteries and will have a default setting of 68°F when powered up. It is easily changed by tapping the arrow keys on the front of the thermostat. Up arrow increases temperature and down arrow reduces temperature. Backlighting is provided on some models and can be turned off or on by a small switch under the left corner of the thermostat. This will allow you to see the thermostat in low light or at night.
This line voltage device should be installed and serviced by a qualified electrician. The thermostat has been designed to mount to a standard 2” x 4” electrical outlet box. Leveling of the thermostat is not required. Mounting screws are provided. Mount the thermostat about five feet above the floor in an open area in the living room. A good rule of thumb is to place the thermostat above the wall switch for that room. This works well for most bedroom and makes it very convenient to turn the heat lower when leaving the room. Avoid mounting the thermostat where there may be plumbing pipes in the wall or placing a lamp or TV too close to the thermostat. The heat from these items affects the performance of the thermostat.
WARNING !
READ CAREFULLY – These instructions are written to help you prevent difficulties that might arise during the installation of the thermostat. Studying the instructions first may save you considerable time and money later. Observing the following procedures will cut your installation time to a minimum. Save these instructions for future use.
Thank you for buying this King Thermostat. It should provide years of service and comfort to your home. Inspect the package. You should have received the thermostat with its cover and two screws to attach it to a wall box.
DISPLAY CHANGE
Fahrenheit to Celsius: On the bottom edge of the thermostat, there are air vents. In one of the vents on the left side, just behind the illumination switch, there is a larger opening with a pin collector attached. With needle nose pliers, pull the connector off. This will put
the thermostat into the metric Celsius mode.
POWER IN
King Electric ES MAX22 non programmable Installation Instruction
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…