Installation, Operation & Application Guide
For more information on our complete range of American-made products – plus wiring diagrams, troubleshooting tips, and more, visit us at www.icmcontrols.com
Important Safety Information
WARNING!: Always turn off power at the main power supply before installing, cleaning, or removing the thermostat.
Package Contents/Tools Required
Package includes: SC5010 PRO thermostat on base, thermostat cover, wiring labels, screws, and wall anchors, 2 “AAA” batteries, Installation, Operation, and Application Guide Tools required for installation: Drill with 3/16” bit, hammer, screwdriver
To Remove Existing Thermostat
ELECTRICAL SHOCK HAZARD – Turn off power at the main service panel by removing the fuse or switching the appropriate circuit breaker to the OFF position before removing the existing thermostat.
ELECTRICAL SHOCK HAZARD – Turn off power at the main service panel by removing the fuse or switching the appropriate circuit breaker to the OFF position before removing the existing thermostat.
IMPORTANT: Thermostat installation must conform to local and national building and electrical codes and ordinances.
Note: Mount the thermostat about five feet above the floor. Do not mount the thermostat on an outside wall, in direct sunlight, behind a door, or in an area affected by a vent or duct.
Heat/Cool Systems
Single Compressor
heat pump with electric backup
Dual Compressor
heat pump with electric backup
the outdoor sensor only reads the outdoor temperature
SC5811 Output Chart
1ST Cool | 2ND Cool | 1ST Heat | 2ND Heat | |
Heat/Cool | Y1,G | YI,Y2,G | W1,G* | W1,W2,G* |
Heat Pump (One Compressor) | Y1,G,O | Y1,G,O | Y1,G,B | Y1,W2,G,B |
Heat Pump (Two Compressors) | Y1,G,O | Y1,Y2,G,O | Y1,G,B | Y1,Y2,G,B |
Emergency Heat (Heat Pump Only) | N/A | N/A | W2,G | W2,G |
The SC5811 thermostat is configurable for all systems. The configuration directly affects the outputs. Use the output chart to correctly configure and wire the thermostat to your system.
The configuration mode is used to set the SC5811 to match your heating/cooling system. The SC5811 functions with a heat pump, air conditioning, gas, oil, or electric heat systems. To configure the SC5811, perform the following steps:
The setup screens for Configuration Mode are as follows:
Choose | System | Reversing Valve Active | Number of Compressors or Compressor Stages | Type of Heat |
Heat Pump | HP | O | 1 | |
HP | b | 1 | ||
HP | O | 2 | ||
HP | b | 2 | ||
Non-Heat Pump | Heat | Gas | ||
Heat | Electric |
Press the up or down button to select. Press the CONFIG button for 2 seconds to exit the configuration.
The SC5010 is a programmable, manual or auto changeover, single-stage heat, and single-stage cool thermostat. It functions with air conditioning, heat pumps, gas, oil, or electric heat systems. The thermostat activates the heating appliance when the room temperature is below the set heat temperature (by the differential temperature) and the red indicator light (configurable) on the thermostat will light. The SC5010 will stop outputting and the red light will turn off when the call for heat has been satisfied. With heat pumps, the thermostat will not let the compressor come on for 4 minutes after it turns off. This protects your compressor. When the room temperature is greater than the set cool temperature (by the differential temperature), the cooling device is activated and the green indicator light (configurable) on the thermostat will turn on. The SC5010 will stop outputting and the green light will turn off when the call for cooling is satisfied. The thermostat will not let the compressor come on for 4 minutes after it turns off. This protects your compressor.
The SC5010 has five possible operating modes: OFF, Heat, Cool, Heat & Cool, and Program mode. In off mode, the thermostat will not turn on heating or cooling devices. The manual fan can be turned on in all operating modes using the fan button. In heat mode, the thermostat controls the heating system. In cool mode, the thermostat controls the cooling system. In heat & cool mode, the thermostat controls both the heating and cooling systems. In program mode, the thermostat will automatically be controlled by the set program. Program mode can function with heat mode, cool mode, or heat & cool mode. The clock display alternates with the set temperature display for heat & cool modes.
The programmable fan feature can be used to run the fan during occupied periods. The program schedule can be overridden by changing the set temperature (up or down button). This puts the SC5010 thermostat on a 2-hour temporary hold. After 2 hours, it will automatically return to the program schedule. The SC5010 also has a button lockout feature. This enables the thermostat to be set to the proper mode and temperature and locked so it cannot tamper with.
UP – Used to increase the time, set temperatures, and adjust the configuration settings.
DOWN – Used to decrease the time, set temperatures, and adjust configuration settings.
SYS (left) – Used to change from OFF, HEAT, EMERGENCY HEAT, COOL, and AUTO changeover modes
FAN (right) – Used to turn on and off the indoor fan.
PROG (SYS and FAN) – Used to change from program operation to manual operation.
UP and PROG – Held in simultaneously for 10 seconds to lock and unlock the thermostat.
DOWN and SYS – Pressed simultaneously to display outdoor remote temperature if the remote sensor is connected.
Operating Modes
There are five possible operating modes for the SC5010. Off, Cool, Heat, and Cool & Heat modes are accessed by pressing the SYS (left) button. Program mode is accessed by pressing the SYS (left) and FAN (right) buttons simultaneously.
OFF Mode
In this mode, the thermostat will not turn on the heating or cooling devices
Note: The indoor fan can be turned on manually in every operating mode by pressing the FAN (right) button. The word FAN shows on the display and the fan icon appears when the fan
Heat Mode
In this mode, the thermostat controls the heating system. When the heat outputs, the flame icon
Note: For heat pumps, there is a four-minute delay for your compressor to restart after it has turned off.
Cool Mode
In this mode, the thermostat controls the cooling system. When the cooling outputs, the snowflake icon
Note: There is a four-minute delay for your compressor to restart after it has turned off.
Cool and Heat Mode (Auto Changeover)
In this mode, the thermostat controls the cooling and heating systems, automatically changing over from one to the other as needed. The timing display alternates with the set temperature every 10 seconds in the cool and heat mode.
Program Mode
In this mode, the program function is on (PROG displays), and the thermostat will automatically be controlled by the set program schedule. Program mode can function with heat mode, cool mode, or heat & cool mode. The program schedule can be overridden by changing the set temperature (up or down button). After 2 hours, the program schedule will automatically be resumed. To manually return to the program schedule, press the PROG button twice.
Setting the Time and Day of the Week
The time and day of the week must be set for your program schedule to operate correctly.
From this screen you have 2 options:
From any of the previous screens, you can press the FAN (right) button to begin entering your program schedule. The days shown on the display will all be programmed simultaneously.
When the program schedule is complete, press and hold the PROG button (SYS and FAN buttons pressed simultaneously) for 2 seconds to return to the OFF mode
Lockout Feature
The SC5010 has a button lockout feature so the mode cannot be changed and the temperature adjustment is limited. Select the appropriate lockout from Configuration Mode Settings (Step 5) of this guide. To activate the LOCK feature:
Factory Preprogramming
The SC5010 comes preprogrammed with the following schedule:
|
|
|
|
Personal Program Schedule
Use the following personal program schedule to record your settings
Requires SimpleSetTM Transfer Cable (ACC-WIH21)
This feature is used for transferring configuration and program schedule from the master to the target thermostat. All thermostats for a job can be mounted and powered up. Configure and program one thermostat. This will be the master. The master will be used to copy the program to the rest of the thermostats
Preparing the master to Send:
Note: The target thermostat must be powered with 24 VAC for field programming to occur When the connection has been made correctly, the master thermostat will power up and the target will count from 5 down to 1. It will then display the LOCK confirming the data has been saved in memory. When all target thermostats have been completed, reinstall the master thermostat.
Press the up and down buttons and the CONFIG switch simultaneously for 5 seconds to exit from the data transfer mode and to return the master thermostat to the OFF mode.
Symptom | Remedy |
No display | Check for 24 VAC at thermostat; display is blank when 24 VAC is not present or if batteries are completely discharged. Time and day of week must be reset after extended power loss. |
System fan does not come on properly | Verify wiring is correct, check Gas/Electric Configuration (see Setting 4). |
No response with first button press | First button press activates backlight only (when back light is configured “ON”). |
Program schedule activates at the wrong time | Check time (AM/PM) set on thermostat (see Setting the Time). |
Thermostat turns on and off too frequently | Adjust temperature differential (see Configuration Mode Setting 2). |
Thermostat does not follow program | Verify it is operating in program mode (PROG displays); check time (AM/PM); may be in 2 hour program override. |
Fan runs continuously | Press FAN (right) button to turn fan off. |
Fan turns on occasionally | Program Mode: Check programmable fan setting in program mode schedule. |
Status indicator light not on during call | Turn status indicator function on (see Configuration Mode Setting 12). |
Room temperature is not correct | Calibrate thermostat (see Configuration Mode Setting 8). If remote sensor is used, check S1 & S2 terminal connections. Press SYS and down buttons to display outdoor temperature. |
Thermostat has the button lockout function activated (see Lockout Feature, and Configuration Mode Setting 5). | |
on display instead of room temp. | Check for a bad connection at S1 & S2 terminals, if used (see Configuration Mode Setting 10). |
Heat or Cool not coming on | Verify wiring is correct, verify RC/RH jumper is in place (for single transformer system). |
Remote or outdoor sensor not accurate | Press SYS and down buttons simultaneously to display remote or outdoor temperature. Verify connections at S1 and S2 terminals. |
LO BAT on display | Replace batteries with two fresh “AAA” batteries. LO BAT may display if no batteries are installed and there is a loss of power. |
Problem not listed above | Press Reset button once*. |
The Seller warrants its products against defects in material or workmanship for a period of five (5) years from the date of manufacture. The liability of the Seller is limited, at its option, to repair, replace or issue a non-case credit for the purchase prices of the goods which are provided to be defective. The warranty and remedies set forth herein do not apply to any goods or parts thereof which have been subjected to misuse including any use or application in violation of the Seller’s instructions, neglect, tampering, improper storage, incorrect installation or servicing not performed by the Seller. In order to permit the Seller to properly administer the warranty, the Buyer shall: 1) Notify the Seller promptly of any claim, submitting date code information or any other pertinent data as requested by the Seller. 2) Permit the Seller to inspect and test the product claimed to be defective. Items claimed to be defective and are determined by Seller to be non-defective are subject to a $30.00 per hour inspection fee. This warranty constitutes the Seller’s sole liability hereunder and is in lieu of any other warranty expressed, implied, or statutory. Unless otherwise stated in writing, Seller makes no warranty that the goods depicted or described herein are fit for any particular purpose.
7313 William Barry Blvd., North Syracuse, NY 13212
(Toll-Free) 800-365-5525 (Phone) 315-233-5266 (Fax) 315-233-5276 www.icmcontrols.com
DOWNLOAD MANUALS:
icm control SC5811 Programmable Electronic Thermostat Installation Guide
icm control SC5811 Programmable Electronic Thermostat Installation Guide
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…