Your thermostat has been pre-programmed from the factory with no programming necessary. We recommend using these pre-programmed settings for a few days before altering them as they offer maximum energy-saving benefits. If you do decide to alter your programs, use the charts on page 13 to write out your scheduled times and temperatures. After you have recorded your preferences, follow the instructions on page 14 to alter your temperature settings. There is no need to program the thermostat on the wall where it is mounted! Remove the thermostat from the backplate by gripping the sides firmly and pulling it straight off. This allows you to program the thermostat in comfort. After you have programmed your thermostat, no other setting changes are necessary unless you wish to browse through the menu to see how you may further adjust the independent settings of your thermostat to meet your lifestyle. The features section starting on page 28 of this manual will describe these settings. Most settings have been preset for optimal performance. If you need any assistance with the installation or setup of your newHunter Thermostat, please call us, our technical support staff is ready to help! USA: 1-888-830-1326 Canada: 1-866-268-1936 Hours of operation are from 7:00 am to 7:00 pm Monday – Friday and 8:00 am to 5:00 pm on Saturday, Central Time. You may also contact us over the Internet at: www.HunterFan.com
Conventional System: Uses a condensing unit for cooling and a separate furnace system for heating.
Heat Pump System: Uses the condensing unit for both heating and cooling.
NOTE: If you are unsure of your system type it may be necessary to contact our technical support department at 1-888-830-1326, your HVAC manufacturer, or a local HVAC technician to determine this. Improper selection of your system type could cause the thermostat to not operate your system properly.
Setting Day and Time
Once you install the batteries, the thermostat will prompt you to set the current day and time.
Read the scheduling section thoroughly to ensure you understand your scheduling options and which will best fit your lifestyle. The following notes should help you with scheduling:
This thermostat has been pre-programmed to provide optimal energy savings. No programming is necessary. We recommend you run these programs for a few days before adjusting your programming. If it is necessary to change these settings, use the scheduling table on the next page to record your new settings. You will also find the default schedule there as well
Default Schedule
Day | Away | Asleep | Home |
Monday-Friday | Start Time: 8:00am End Time: 6:00pm Heat Temp: 60OF (16OC) Cool Temp: 85OF (29OC) | Start Time: 10:00pm End Time: 6:00am Heat Temp: 60OF (16OC) Cool Temp: 82OF (28OC) | Heat Temp: 68OF (20OC)
Cool Temp: 78OF (26OC) |
Saturday | Start Time: 8:00am End Time: 4:00pm Heat Temp: 60OF (16OC) Cool Temp: 85OF (29OC) | Start Time: 10:00pm End Time: 6:00am Heat Temp: 60OF (16OC) Cool Temp: 82OF (28OC) | Heat Temp: 68OF (20OC)
Cool Temp: 78OF (26OC) |
Sunday | Start Time: 8:00am End Time: 4:00pm Heat Temp: 60OF (16OC) Cool Temp: 85OF (29OC) | Start Time: 10:00pm End Time: 6:00am Heat Temp: 60OF (16OC) Cool Temp: 82OF (28OC) | Heat Temp: 68OF (20OC)
Cool Temp: 78OF (26OC) |
The Home schedule automatically calculates the remaining times from Away and Asleep and assigns them the Home temperature.
Alternate Schedule
Day | Away | Asleep | Home |
Monday-Friday | Start Time: End Time: Heat Temp: Cool Temp: | Start Time: End Time: Heat Temp: Cool Temp: | Heat Temp:
Cool Temp: |
Saturday | Start Time: End Time: Heat Temp: Cool Temp: | Start Time: End Time: Heat Temp: Cool Temp: | Heat Temp:
Cool Temp: |
Sunday | Start Time: End Time: Heat Temp: Cool Temp: | Start Time: End Time: Heat Temp: Cool Temp: | Heat Temp:
Cool Temp: |
Note: Use a pencil so these records may be changed at a later time if necessary.
Note: If you do not wish to use the scheduling option on your thermostat, refer to page 20, step 2.
Temporary Temperature Change
With Temporary Temperature Change you have the ability to alter the temperature for only the current running schedule.
Note: Temporary Temperature Change is not a permanent setting. Your thermostat will only run the new temperature until the next scheduled period change. After your thermostat
changes to a new schedule set, your thermostat will forget the temporary setting and resume your existing schedule.
Temporary Schedule Change
Turning Off Scheduling
To turn off your schedule and have the thermostat permanently set to one temperature:
The Save Away feature allows you to set a lower or higher temperature for the time you will be away from your home outside of your normal Away schedule. This can include days you will be away for vacation, or a few hours away from your home. The Save Away feature can be set for as little as 1 hour or as many as 30 days. To set the save away feature:
This chapter will outline the various alerts the thermostat will report to you and how to respond to them.
Under your Menu options, you have the ability to reset your filter counter, change your day/time settings, and change first and second stage spans. To change each setting, you will need to hit the Next button to move through each feature.
To access these options:
There is no need to stand at the wall where the thermostat is mounted while programming or changing settings. Simply remove the thermostat from the wall and make the necessary changes in the comfort of a chair. You can also set your programming and settings before you even install the thermostat.
Armchair Programming
Your thermostat has a blue LED lamp that backlights the display for easy viewing in the dark. When any key is pressed, the backlight will be activated. The display will stay illuminated for 15 seconds after the last key is pressed.
Blue Backlight
To protect your system from cycling, the system turns on and off rapidly, and your thermostat will prevent your system from turning back on for up to 3.5 minutes after it has been shut down.
System Protection
In situations where your thermostat may not seem to be operating properly or if you just want to reset and start over, press and hold the buttons for 3 seconds until the screen flashes “Updated!”. This will restore the thermostat to factory condition.
Problem
No display.
Solution
Problem
The program does not change at the desired setting.
Solution
Problem
The auto / Fan does not turn on.
Solution
Problem
The fan runs continuously.
Solution
1. Check the fan setting to see if it is set to on.
2. Move HG/HE switch to the opposite position.
Problem
The heating or cooling does not turn on or off.
Solution
Problem
Backlight does not come on.
Solution
If you need any assistance with the installation or setup of your new Hunter thermostat, please call us. Our technical support staff is ready to help! USA: 1-888-830-1326 Canada: 1-866-268-1936 Hours of operation are from 7:00 am to 7:00 pm Monday – Friday and 8:00 am to 5:00 pm on Saturday, Central Time. You may also contact us over the Internet at www.HunterFan.com.
Hunter Fan Company
Thermostats
LIMITED WARRANTY
The Hunter Fan Company warrants your Hunter Thermostat to be free from defects in material or workmanship for a period of one year from the date of sale to the original user or consumer purchaser. If your Hunter Thermostat malfunctions or fails within the warranty period because of a defect in material or workmanship, we will replace it. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO YOUR HUNTER THERMOSTAT IS LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE. This warranty is voided if your Hunter Thermostat is not purchased and used in the USA. This warranty excludes and does not cover defects, malfunctions or failures or your Hunter Thermostat which were caused by repairs by persons not authorized by us, mishandling, improper installation, modifications or damage to the Hunter Thermostat while in your possession, or unreasonable use, including failure to provide reasonable and necessary maintenance.
This warranty neither applies to batteries nor to deterioration of, nor damage to the product caused by the use of faulty batteries. Return your product, along with proof of purchase to Hunter Fan Company Service Department, 7130 Goodlett Farms Pkwy Suite 400, Memphis, TN 38016. You will be responsible for all insurance and freight or other transportation charges to our factory. We will return your Hunter Thermostat freight prepaid. Your Hunter Thermostat should be properly packed to avoid damage in transit since we will not be responsible for any such damage. Proof of purchase is required when requesting warranty service. IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THE WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE
Download Manual
Hunter 44273 Programmable Thermostat Owner Manual
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…