Honeywell TH8732WFH5004 Round Smart Thermostat User Guide

Honeywell TH8732WFH5004 Round Smart Thermostat

System Types
Compatible with 24-volt systems such as forced air, hydronic, heat pump (including dual fuel), oil, gas and electric.
Does not work with electric baseboard heat (120/240V).

Mercury Notice:
If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact the Thermostat Recycling Corporation at 1-800-238-8192 or thermostat-recycle.org for information on how and where to properly and safely dispose an old thermostat.
Disconnect power before installation.
Can cause electrical shock or equipment damage.

Must be installed by a trained, experienced technician.
Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition.

Installation

1. Set Jumper Switches
   • For single transformer systems, move switch up.
   • For dual transformer systems, move switch down.

     Jumper Switch for humidifier, dehumidifier, or ventilation:

      

   • For single wire products, set the switch to 1 Wire.

      

   • For two wire products, set the switch to 2 Wire.
2. 2 Wiring: Terminal Designations
   • L Heat pump system monitor
   • C Common wire from secondary side of cooling transformer, if 2 transformers
   • W2 (AUX) :2nd stage heat relay (heat pump auxiliary, emergency heat)
   • W (O/B ):1st stage heat relay (changeover (O/B) valve for heat pumps)
   • U1: Terminal for indoor air quality products (humidifier, dehumidifier, ventilator)
   • U2 : Terminal for indoor air quality products (humidifier, dehumidifier, ventilator)
   • K: Optional C-wire adaptor
   • G:Fan relay
   • Y2:2nd stage compressor contactor
   • Y: 1st stage compressor contactor
   • R: Heating power. Connect to the secondary side of the heating system transformer
   • Rc: Cooling power. Connect to the secondary side of the cooling system transformer
3. Connect wires and mount wallplate
   Connect wires and mount the wall plate using screws and anchors provided.
   Note: The illustration to the right shows the most common wiring.
   REQUIRED: A C-Wire (common wire) is needed for 24 VAC power.
   Electrical Ratings:

   Terminal                                       Voltage (50/60 Hz)             Max. Current Rating
   W – O/B (Heating)	18 to 30 VAC	1.00 A
   W2 – Aux/E (Heating)	18 to 30 VAC	0.60 A
   Y (Cooling)	18 to 30 VAC	1.00 A
   Y2 (Cooling)	18 to 30 VAC	0.60 A
   K	18 to 30 VAC	1.00 A
   G (Fan)	18 to 30 VAC	0.50 A
   L (Output)	18 to 30 VAC	1.00 A
   U1, U2	18 to 30 VAC	0.40 A

4. Firmly snap the thermostat into place
   The thermostat will glow and display the screen for up to three minutes while it starts up.

Setup: On-screen menus

1. Press and hold (The weather button) for 5 seconds to access the Main Menu.
2. using ▼, highlight Device Details and press OK. Using▼, find the 4-digit password (date code) and record it above.
   Press OK to exit.
3. Using▲, highlight Set Up and press OK.
4. Using ▼, highlight Contractor and press OK.
   Setup: On-screen menus_ _ _ _
5. Enter the password by pressing ▲ or ▼to select the first digit and press OK. Continue for all four digits.
6. Highlight Set Up and press OK.
7. Press ▲ or ▼to highlight the setting and press OK. Continue until all settings have been configured. For a full list of setup options, see “Setup options” on page 3.Note: To exit setup early, press ▼ to highlight EXIT and press OK.
8. When all settings are configured, save changes.To save and confirm, highlight Yes and press OK. To exit without saving, press ▼ to highlight No and press OK.

Setup options

1. From the Contractor Menu, highlight Set Up and press OK.
2. Press ▲ or ▼ to highlight the setting and press OK. Continue until all settings have been configured.
3. When all settings are configured, you will be prompted to save changes. Highlight Yes and press OK to save and exit. To exit setup early by pressing ▼ to highlight EXIT and press OK.

ISU #	Description	Setting
1160	Temperature indication scale	0 = Fahrenheit 1 = Celsius
2120	Heating system type	1 = Conventional forced air heat 2 = Heat pump 3 = Radiant heat 5 = None (cool only)
2140	Heating equipment type	Conventional Forced Air Heat: 1 = Standard efficiency gas forced air 2 = High efficiency gas forced air 3 = Oil forced air 4 = Electric forced air 5 = Hot water fan coil
		Heat Pump: 7 = Air to air heat pump 8 = Geothermal heat pump
		Radiant Heat: 9 = Hot water radiant heat 12 = Steam
2160	Reversing valve O/B	0 = O (O/B on cool) 1 = B (O/B on heat)
2180	Cool stages / compressor stages	0, 1, 2
2200	Heat stages / backup heat stages	Heat stages: 0, 1, 2 Backup heat stages: 0, 1
2220	Fan operation in heat	0 = No fan 1 = Equipment controls fan 2 = Thermostat controls fan
2240	Backup heat type	31 = Electric forced air 32 = Gas/Oil Forced air (or Fossil forced air)
2260	External Fossil Fuel Kit	0 = Thermostat controls backup heat 1 = External Fossil Fuel Kit controls backup heat
3120	Staging control	Comfort
	– backup heat	2.0°F to 15.0°F from setpoint (in 0.5°F
	differential	increments)
		1.0°C to 7.5°C from setpoint (in 0.25°C
		increments)
3140	Backup heat upstage timer	Off 30, 45, 60, 75, 90 minutes 2, 3, 4, 5, 6, 8, 10, 12, 14, 16 hours
3160	Compressor lockout /	Off
	balance point	5°F to 60°F (in 5°F increments)
		-15.0°C to 15.5°C (in 2.5°C or 3.0°C
		increments)
3180	Backup heat lockout	Off 5°F to 65°F (in 5°F increments) -15.0°C to 18.5°C (in 2.5°C or 3.0°C increments)
3200	Cool cycles per hour	1 – 6
3220	Cool cycles per hour – stage 2	1 – 6
3240	Heat cycles per hour	1 – 12
3260	Heat cycles per hour – stage 2	1 – 12
3280	Backup heat cycles per hour	1 – 12
4120	Adaptive intelligent recovery	0 = No 1 = Yes

ISU #	Description	Setting
4160	Minimum setpoint (Note: Setting applies to both heat and cool setpoints)	50°F to 99°F 10.0°C to 37.0°C
4220	Maximum setpoint (Note: Setting applies to both heat and cool setpoints)	40°F to 90°F 4.5°C to 32.0°C
8100	Humidifier type	0 = None 1 = Steam 2 = Bypass or fan powered
8120	Humidification – window protection	0 = Off 1  = On
8140	Humidification control	0 = Humidify only when heat is On 1 = Humidify only when fan is On 2 = Humidify on demand: Thermostat controls fan 3 = Humidify on demand: Humidifier controls fan
9100	Dehumidification equipment	0 = None 1 = A/C with low speed fan 2 = A/C with high speed fan 4 = Whole house dehumidifier
9140	Dehumidification equipment setup	0 = Normally open 1 = Normally closed
9160	Dehumidification – overcooling limit	0, 1, 2, 3°F 0.0, 0.5, 1.0, 1.5°C
9180	Dehumidifier fan control	0 = Thermostat controls fan 1 = Equipment controls fan
10100	Ventilation type	0 = None 1 = ERV / HRV 2 = Passive (fan only) 3 = Fresh air damper
10160	Ventilation fan control	0 = Thermostat controls fan 1 = Equipment controls fan
10240	Ventilation per cent on time	10% to 100% (in 10% increments)
10280	Ventilation low-temperature lockout	Off -20°F to 40°F (in 5°F increments) -29.0°C to 4.5°C (in 2.5°C or 3.0°C increments)
10300	Ventilation high-temperature lockout	Off 80°F to 110°F (in 5°F increments) 26.5°C to 43.5°C (in 2.5°C or 3.0°C increments)
10320	Ventilation high dew point lockout	Off 65°F to 85°F (in 5°F increments) 18.5°C to 29.5°C (in 2.5°C or 3.0°C increments)
11100	Home heat setpoint	40°F to 90°F 4.5°C to 32.0°C (in 0.5°C increments)
11120	Home cool setpoint	50°F to 99°F 10.0°C to 37.0°C (in 0.5°C increments)
11140	Setpoint for away mode	0 = Away setpoints 1 = Smart temperature setpoints
11160	Away heat setpoint	40°F to 90°F 4.5°C to 32.0°C (in 0.5°C increments)
11180	Away cool setpoint	50°F to 99°F 10.0°C to 37.0°F (in 0.5°C increments)
14020	Temperature display offset	-3°F to 3°F
14025	Humidity % offset	-12% RH to 12% RH

Basic Operations

NEED HELP?
For assistance with this product, please visit customer.resideo.com or call Customer Care toll-free at 1-800-633-3991.

FCC REGULATIONS
47 CFR § 15.19 (a)(3)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation

47 CFR § 15.21 (USA only)
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

47 CFR § 15.105 (b)
See https://customer.resideo.com/en-US/support/residential/codes-and-standards/FCC15105/Pages/default.aspx for additional FCC information for this product.
IC REGULATIONS
RSS-GEN
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The operation of this equipment is subject to the following two conditions:

1. this equipment or device may not cause harmful interference, and
2. this equipment or device must accept any interference, including interference that may cause undesired operation.

©2019 Resideo Technologies, Inc.
This product is manufactured by Resideo Technologies, Inc., Golden Valley, MN, 1-800-633-3991.
The Honeywell Home trademark is used under license from Honeywell International Inc. All rights reserved.

Resideo Inc., 1985 Douglas Drive North Golden Valley, MN 55422
www.resideo.com 33-00445EFS—05 M.S. Rev. 04-19
Printed in the United States

Search for local rebates: HoneywellHome.com/Rebates

Reference

Download manuals:

Honeywell TH8732WFH5004 Round Smart Thermostat User Guide

Honeywell TH8732WFH5004 Round Smart Thermostat User Guide

Honeywell TH8732WFH5004 Round Smart Thermostat User Guide