HONEYWELL TH6320R Wireless Thermostat Operating Manual

HONEYWELL TH6320R Wireless Thermostat

Quick Reference Card
Grasp and pull to see basic operating instructions at a glance

Battery Holder
Press down and pull to remove the batteries. Batteries should be replaced once a year (see page 16).

CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage, do not operate the cooling system when the outdoor temperature is below 50°F (10°C).

Need Help?
For assistance with this product please visit http://yourhome.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502

Read and save these instructions
® U.S. Registered Trademark. Patents pending. Copyright © 2008 Honeywell International Inc. All rights reserved.

About your new thermostat

Your new thermostat is pre-programmed and ready to go. All you have to do is set the time and day. Then check the settings below and change if needed:

1. Set time and day (required for proper operation)…………… See page 5
2. Select fan setting (Auto/On)……………………………………………. See page 6
3. Select system setting (Heat/Cool) ………………………………….. See page 7
4. Program schedules: Preset to energy-saving levels while you’re at work or asleep (assumes you wake at 6 am, leave at 8 am, return at 6 pm and go to bed at 10 pm)………………………………………………… See pages 8-9

ONE-TOUCH TEMP CONTROL: You can override the program schedule at any time, and manually adjust the temperature (see pages 10-11).

A quick reference to controls

A quick reference to the display screen

Set the time and day

1. Press SET CLOCK/DAY/SCHEDULE, then press or to set clock.
2. Press SET DAY, then press or to select the day of the week.
3. Press DONE to save.

Note: If the SET CLOCK/DAY/SCHEDULE option is not displayed, press DONE or CANCEL.
Note: If the display flashes Set Clock, the thermostat will follow your settings for the weekday “Wake” period until you reset the time and day.

Select the fan setting

Press FAN to select Auto or On. In “Auto” mode (the most commonly used setting), the fan runs only when the heating or cooling system is on. If set to “On,” the fan runs continuously.

Note: Options may vary depending on your heating/cooling equipment.

Select the system setting

Press SYSTEM to select:

• Heat: The thermostat controls only the heating system.
• Cool: The thermostat controls only the cooling system.
• Off: All systems are off.
• Auto: The thermostat automatically selects heating or cooling depending on the indoor temperature.
• Em Heat (only for heat pumps with auxiliary heat): The thermostat controls Emergency and Auxiliary Heat. The compressor is locked out.

Note: Options may vary depending on your heating/cooling equipment.

EnergyStar® settings for maximum cost savings

This thermostat is pre-set to use EnergyStar® program settings. We recommend these settings since they can reduce your heating/cooling expenses by as much as 33%. (See next page to adjust times and temperatures of each period.)

To adjust program schedules

1. press SET CLOCK/DAY/SCHEDULE, then SET SCHEDULE.
2. Press or to set your weekday Wake time (Mon-Fri), then press NEXT.
3. Press or to set the temperature for this period, then press NEXT.
4. Set time and temperature for the next period (Leave). Repeat steps 2 and 3 for each weekday period. 5 Press NEXT to set weekend time periods (Sat-Sun), then press DONE to save & exit.

Note: Make sure the thermostat is set to the system you want to program (Heat or Cool).

Program schedule override (temporary)

Press or to immediately adjust the temperature. This will temporarily override the temper-ature setting for the current period. The new temperature will be maintained only until the next programmed period begins (see page 8). To cancel the temporary setting at any time, press CANCEL.

Program schedule override (permanent)

Press HOLD to permanently adjust the temperature. This will override the temperature settings for all periods. The “Hold” feature turns off the program schedule and allows you to adjust the thermostat manually, as needed. Whatever temperature you set will be maintained 24 hours a day, until you manually change it, or press CANCEL to resume the programmed schedule.

Auto Changeover (heat/cool)

Auto Changeover is a feature used in climates where both air conditioning and heating are often used on the same day. When the system is set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature. Heat and cool settings must be at least 3 degrees apart. The thermostat will auto-matically adjust settings to maintain this 3-degree separation.

Remote control

The optional remote control can act as a mobile thermostat, to maintain a comfortable temperature as you move from room to room. When the system is responding to temperatures measured at the Remote, the thermostat will display Remote has Control. Press CANCEL to restore temperature control to the thermostat (the system will only respond to temperatures measured at the thermostat).

Note: The thermostat may take up to 15 seconds to respond to commands entered at the remote control. See Remote Control Operating Manual for more information.

Additional features

To display outdoor climate
If you have an outdoor air sensor, press MORE to display the current outdoor tem-perature and humidity. Press DONE to exit.

To find a lost remote control
If you misplace a remote control, press MORE, then FIND REMOTE. The remote will beep for two minutes to help you locate it. Press anywhere on the display screen to stop the beeping.

Special features

Built-in compressor protection: This feature helps prevent damage to the compressor in your air conditioning or heat pump system. Damage can occur if the compressor is re-started too soon after shutdown. This feature forces the compressor to wait for a few minutes before restarting. During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump). Adaptive Intelligent Recovery: This feature eliminates guesswork when setting your schedule. It allows the thermostat to “learn” how long your furnace and air conditioner take to reach programmed temperature settings, so the temperature is reached at the time you set.

Note: When Adaptive Intelligent Recovery is in effect, the thermostat will display “Recovery”.

Battery replacement (thermostat)

Install fresh batteries when the REPLACE BATTERY warning begins flashing. The warning flashes about two months before the batteries are depleted. Remove the battery holder and install 2 fresh AA alkaline batteries. After batteries are installed, the thermostat will automatically restore communication with the wireless network within a few minutes.

Note: If batteries are inserted within t2 minutes, the time and day will not have to be reset. All other settings are retained in memory.

Battery replacement (outdoor air sensor)

Replace outdoor sensor batteries when the REPLACE BATTERY OUTDOOR warning begins flashing on the thermostat. The warning flashes about two months before the batteries are depleted. Remove the sensor from the bracket, remove the cover, and install 2 fresh AA lithium batteries. After batteries are installed, the sensor will automatically restore communication with the wireless network within a few minutes.

In case of difficulty

Up to 5-year limited warranty

Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for three (3) years from the date of purchase by the consumer. If at any time during the warranty period, the product is determined to be defec-tive or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or
(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will determine whether the product should be returned to the following address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage that occurred while the product was in the possession of a consumer. Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY,

FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of inci-dental or consequential damages, so this limitation may not apply to you. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this warranty, please write Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502. In Canada, write Retail Products ON15-02H, Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V4Z9. When the product is registered online at www.warranty.Honeywell.com, the standard manufacture coverage stated above extends to a period of (5) years.

Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North Golden Valley, MN 55422
http://yourhome.honeywell.com
69-2093EFS-01 Honeywell Limited-Honeywell Limitée 35 Dynamic Drive
Scarborough, Ontario M1V 4Z9

Reference

Download Manual:

HONEYWELL TH6320R Wireless Thermostat Operating Manual

HONEYWELL TH6320R Wireless Thermostat Operating Manual