RECOMMENDED THERMOSTATS, DAMPERS, AND ACCESSORIES
The following are suggested thermostats, dampers, and accessories for use with the TrueZONE panel.
Table 1. Recommended Thermostats.
System | Non-Programmable | Programmable |
Heat Pump | TH3210D, TH5220D, TH5320U | TH4210D, TH6220D, TH8220U, TH8321U, YTH9421C |
Note: These thermostat models all have different four-digit suffixes. All versions of the model numbers listed above will work with the applications they’re listed for.
Table 2. Recommended Dampers.
Type | Honeywell Damper | Round | Rectangular |
Zone | Spring-open/ power-closed | ARD | ZD |
Zone | Power-open/ power-closed | MARD/ RRD | For recommended dampers call the Honeywell Zoning Hotline at 1-800-828-8367. |
Bypass | Static pressure regulating damper | SPRD | SPRD |
Table 3. Maximum Dampers.*
Ambient Temp. | Maximum Damper VA per Zone |
100°F (38°C) | 28.8 |
160°F (71°C) | 16.8 |
Use an SDCR (Slave Damper Control Relay) for additional dampers.
Maximum dampers per panel is limited by transformer size.
Ensure the transformer is large enough to power the panel (6.25 VA) and dampers.
Table 4. Accessories.
Accessory | Description |
40 VA transformer* | AT140A1042* |
75 VA transformer | AT175A1008 |
Discharge Air Temperature Sensor (DATS)* | DATS C7735A1000* |
SDCR | Slave Damper Control Relay |
* Included in HZ221K kit.
The HZ221 TrueZONE panel contains an LED display that communicates the system and zone status. The LEDs indicate the following information.
Table 5. LED Operation.
Table 5. LED Operation. | |
LED | Description |
HEAT | Solid when in heat. Blinking when DATS temperature exceeds 120°F (49°C) and calling for heat pump only. Blinking when DATS temperature exceeds 160°F (71°C) and calling for heat pump and auxiliary heat. At 150°F (66°C), auxiliary heat is disabled. |
COOL | Solid when in cool. Blinking when 45°F (7°C) DATS low limit mode has been reached. |
FAN | Solid when in operation. |
PURGE | Solid when in purge (lasts 2 minutes at power-up and after a call for heat or cool). Blinking when the DATS sensor has failed, or the wires are shorted or open. Will blink for 3 minutes at power-up if DATS is not present. |
ZONE 1, 2 | Solid green when open or opening. Solid red when closed or closing. Blinking amber when there is a damper or thermo- stat short circuit (circuit breaker trip). |
EM HEAT | Solid when in Em Heat mode. |
When the zone panel cover is off, the EMERGENCY HEAT/PURGE OVERRIDE button is visible.
When the panel is in Purge (at startup or after a call for heat/cool), pressing this button stops the Purge, which saves time during installation or troubleshooting.
All other times, pressing the button puts the zone panel into Em Heat mode so that all calls for heat are handled by the auxiliary heat.
Honeywell warrants the products in this catalog (except those parts designated on Honeywell’s price lists as not covered by this warranty) to be free from defects due to workmanship or materials, under normal use and service, for the following warranty periods. Honeywell VisionPRO®, Commercial VisionPROTM, FocusPRO®, PRO 4000, PRO 3000, LineVoltTM PRO, Digital RoundTM, and Modern RoundTM (T87K, N) Series Thermostats with a date code of 0501 or later: sixty (60) months from date of installation. CommercialPRO, PRO 2000 and PRO 1000 thermostats: twenty-four (24) months from date of installation. All other Honeywell thermostats and thermostats with a date code of 0452 or earlier: twelve (12) months from date of installation, unless specified otherwise. Honeywell Air Cleaners, Humidifiers, Ventilators, Ultraviolet Treatment and Zoning Products with a date code of 0501 or later, excluding replacement maintenance parts: sixty (60) months from date of installation. All other Honeywell indoor air quality and zoning products with a date code of 0452 or earlier: twenty-four (24) months from date of installation, unless specified otherwise. Variable frequency drive devices (VFD) and accessories: new products for thirty-six (36) months and factory refurbished drives for twelve (12) months from the date of installation when start-up and commissioning is performed by Honeywell VFD Authorized and trained personnel. All VFD warranty return products must have prior authorization (Form No. 87-0284) and be returned only to the VFD Service Center in Chattanooga, TN. MS, MN and Fact Acting 2-position Direct Coupled Actuators: sixty (60) months from date of installation. The warranty period for all other products is twelve (12) months from date of installation.
If a product is defective due to workmanship or materials, is removed within the applicable warranty period, and is returned to Honeywell in accordance with the procedure described below, Honeywell will, at its option, either repair, replace or credit the customer for the purchase price of the product, in accordance with the procedure described below. This warranty extends only to persons or organizations who purchase products in this catalog for resale.
The expressed warranty above constitutes the entire warranty of Honeywell with respect to the products in this catalog and IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL HONEYWELL BE RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY NATURE WHATSOEVER.
Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North Golden Valley, MN 55422
customer.honeywell.com
Automation and Control Solutions Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Toronto, Ontario M1V 4Z9
Printed in the U.S.A. on recycled paper containing at least 10% post-consumer paper fibers.
Download Manual:
Honeywell HZ221 TrueZone Thermostat Installation Guide
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…