Honeywell Home Wireless Remote Control

How it works

If you have one thermostat, you can move the remote control around your home (like a mobile thermostat) to make sure the temperature is comfortable in the room you’re using.
If you have multiple thermostats, you can use the remote control to display and adjust temperatures in each room independently.

If you have only one thermostat Temperature is measured at the thermostat or remote control, as you choose. You can move the remote control as needed, so the room you are using maintains a comfortable temperature.

If you have multiple thermostats Temperature is measured at each thermostat. Press TOGGLE ZONE buttons to choose which room to display and adjust.

Quick reference to display screen

System settings

Press a SYSTEM button to select:

• Heat: The thermostat controls only the heating system.
• Cool: The thermostat controls only the cooling system.
• Off: Heating and cooling systems are off.

AUTO CHANGEOVER

Press and hold HEAT or COOL for 3 seconds to select Auto Changeover (the thermostat automatically selects heating or cooling depending on the indoor temperature).
In Auto Changeover mode, you can press HEAT or COOL to display or adjust the settings for each system.
To exit Auto Changeover mode, press and hold HEAT or COOL for 3 seconds.

Note: The Auto Changeover option is available only if programmed by the system installer.
Note: Emergency Heat can only be set at the thermostat.

Temperature control options (one thermostat)

Both the thermostat and the remote control have built-in temperature sensors. Press a button to choose whether the system responds to temperatures at the thermostat, or at the location of the remote control. If you use the remote control to measure temperature, keep it in an upright position in an area with good air circulation. Do not place it near sources of heat or cold air. Keep away from air ducts, direct sunlight, appliances and electronic devices.

Note: This option will not appear if you have a zone system (more than one thermostat). In zone systems, the temperature is always measured at the thermostats.

Temperature control options (multiple thermostats)

If you have a zone system (more than one thermostat), you can display and adjust the temperature in each zone from the remote control.
Press the arrow buttons until the thermostat zone you want is displayed. After a short delay, the remote will retrieve information, then display the current temperature in that zone.

At the remote control you can change the following settings for each zone independently:

• Temperature
• System setting (heat/cool)
• Temporary hold
• Permanent hold
  (Fan operation and program schedules can be changed only at the thermostat.)

Temperature “hold” (programmable thermostats only)

1. Press to adjust the temperature
   
2. Set a temporary hold time period OR press PERM HOLD.
   

Pressto adjust the temperature.

Temporary hold: Pressto set the “Hold Until” time. When the timer expires (or when you press CANCEL), the temperature will revert to the setting you’ve programmed at the thermostat.
Permanent hold: Press PERM. HOLD to maintain the new temperature permanently. The temperature will remain as you set it until you press CANCEL to revert to the setting you’ve programmed at the thermostat.
Note: If you have a zone system (more than one thermostat), Hold will only apply to the zone displayed at the bottom of the screen. Scroll to another zone to change the temperature in that zone.

Screen lock/unlock

Press and hold the SCREEN LOCK button for 3 seconds to lock or unlock the screen.
If the remote control is set to use Auto Lock, the screen is re-locked 30 seconds after each use. If set to use Manual Lock, press and hold the SCREEN LOCK button to re-lock the screen after use.
You can lock the screen to prevent changes to settings while cleaning. Clean the screen with a soft cloth moistened with warm water or a household window cleaner.
Note: The screen lock button will not appear if the remote control has not been set to use manual or auto lock options (see pages 10-11 to activate this feature).

Customizing features

The remote control has four features that can be turned on or off as desired (see next page).
Press and hold the OFF button until the screen changes (about 3 seconds), then press the right arrow button to enter the setup menu.

Press arrow buttons to select a feature, then YES or NO to turn it on or off. When finished customizing features, press DONE to exit the menu and restore the home screen.

• Manual Lock: Allows you to lock the screen by pressing and holding the LOCK button.
• Automatic Lock: Always locks the screen 30 seconds after each use.
• Button Click: Audible tone sounds to confirm each key press.
• Temp Offset: The remote control displays the actual indoor temperature. If you prefer, you can offset the displayed temperature by up to ± 3 degrees (not displayed when used with more than one thermostat).

Battery replacement

In case of difficulty

Slow response
The thermostat may take up to 15 seconds to respond to commands entered at the remote control.

The heating or cooling system does not respond

• Check the circuit breaker and reset if necessary.
• Make sure the power switch at the heating & cooling system is on.
• Make sure the furnace door is closed securely.
• Wait 5 minutes for the system to respond.

The screen displays “No Signal”

Remote control has lost radio contact with the wireless network (usually because of a power outage). To restore power:

• Check the circuit breaker and reset it if necessary.
• Make sure the power switch at the heating & cooling system is on.
• Make sure the furnace door is closed securely.
  After power is restored, the remote control will automatically restore wireless communication within a few minutes.

1-year limited warranty

Resideo warrants this product, excluding battery, to be free from defects in workmanship or materials, under normal use and service, for a period of one (1) years from the date of first purchase by the original purchaser. If at any time during the warranty period, the product is determined to be defective due to workmanship or materials, Resideo shall repair or replace it (at Resideo’s option).
If the product is defective,

• return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or
• call Resideo Customer Care at 1-800-468-1502. Customer Care will make the determination whether the product should be returned to the following address: Resideo Return Goods, 1985 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Resideo that the defect was caused by damage that occurred while the product was in the possession of a consumer.
Resideo’s sole responsibility shall be to repair or replace the product within the terms stated above. RESIDE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY RESIDEO MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE ONE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this warranty, please write Resideo Customer Care, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502.

Reference Link:

Honeywell Home wireless Remote Control Operating Manual

Honeywell Home Wireless Remote Control Operating Manual