Remove the wallplate from the thermostat by pulling from the bottom, then follow the directions below for mounting.
TH3110D
TH3210D
2H/1C Heat Pump System TH3210D
1H/1C System TH3110D (1 transformer)
1H/1C System TH3110D (2 transformers)
1H/1C Heat Pump System TH3110D [7]
Heat Only System TH3110D
Heat Only System with Fan TH3110D
Cool Only System TH3110D
NOTES
Wire specifications:
Use 18- to 22-gauge thermostat wire. A shielded cable is not required.
Gas or Oil: For gas or oil heating systems, leave the fan operation switch in this factory-set position. (This setting is for systems that control the fan in a call for heat.) Electric or Heat Pump: Change the switch to this setting for heat pumps or electric heat systems. (This setting is for systems that allow the thermostat to control the fan in a call for heat if a fan wire is connected to the G terminal.)
Follow the procedure below to configure the thermostat to match the installed heating/cooling system, and customize feature operation as desired. To begin, press
Compressor Protection
(Setup Function 15): Forces the compressor to wait a few minutes before restarting, to prevent damage. During the wait time, the message Cool On or Heat On (heat pumps only) will flash on the display.
20 Emergency heat
30 Cooling system
70 Thermostat information (for reference only)
If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily.
Display is blank | • Check circuit breaker and reset if necessary. • Make sure power switch at heating & cooling system is on. • Make sure furnace door is closed securely. • Make sure fresh AA alkaline batteries are correctly installed (see page 2). |
Heating or cooling system does not respond | • Set system switch to Heat. Make sure the temperature is set higher than the Inside temperature. • Set system switch to Cool. Make sure the temperature is set lower than the Inside temperature. • Wait 5 minutes for the system to respond. |
Temperature settings do not change | Make sure heating and cooling temperatures are set to acceptable ranges: • Heat: 40° to 90°F (4.5° to 32°C). • Cool: 50° to 99°F (10° to 37°C). |
“Cool On” or “Heat On” is flashing | • Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor. |
“Heat On” is not displayed | • Set the System switch to Heat, and set the temperature level above the current room temperature. |
“Cool On” is not displayed | • Set the System switch to Cool, and set the temperature level below the current room temperature. |
Input: 24 V~ @ 60 Hz, 1.0 A
Electrical Ratings
For assistance with this product, please visit customer.resideo.com. Or call Customer Care toll-free at 1-800-468-1502.
CAUTION: EQUIPMENT DAMAGE HAZARD
M29423B Compressor protection is bypassed during testing. To prevent equipment damage, avoid cycling the compressor quickly.
CAUTION: ELECTRICAL HAZARD
Can cause electrical shock or equipment damage. Disconnect power before beginning installation.
CAUTION: MERCURY NOTICE
If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact your local waste management authority for instructions regarding recycling and proper disposal.
CAUTION: ELECTRONIC WASTE NOTICE
The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health. https://customer.resideo.com/en-US/support/residential/codes-and-standards/FCC15105/Pages/default.Resideo Inc., 1985 Douglas Drive North Golden Valley, MN 55422 69-1929EFS—07 M.S. Rev. 08-20 | Printed in the United States © 2020 Resideo Technologies, Inc. All rights reserved. The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates.
Download Manual
Honeywell Home Pro 3000 Non-Programmable Digital Thermostat Installation Instructions
OTHER MANUAL
Honeywell Home Pro 3000 Wi-Fi Thermostat Product Information
Honeywell Home Pro 3000 Non-Programmable Digital Thermostat Operating Manual
Honeywell Home Pro 3000 Non-Programmable Digital Thermostat Installation Instructions
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…